Acratech Leveling Base 1117 Manual de Usario
Lee a continuación 📖 el manual en español para Acratech Leveling Base 1117 (2 páginas) en la categoría Trípode. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
ACRATECH INC.
QUALITY PRECISION PRODUCTS
CAUTION: READ ALL INSTRUCTIONS BEFORE INSTALLING YOUR NEW
LEVELING BASE.
Thank you for purchasing the Acratech leveling base. Your new leveling base is
manufactured using the finest materials and workmanship. With proper care your
leveling base should last for many years.
The main adjustment knob and is used to tighten and loosen the ball so you can
adjust the leveling base. The knob is often only partially loosened so it will
maintain a controlled amount of friction or tension on the ball. The smaller knob is
preset and cannot be adjusted.
INSTALLING YOUR LEVELING BASE ON YOUR TRIPOD
1) If the threaded hole in the bottom of your new leveling base is larger in
diameter than the threaded stud on top of your tripod, then install the
brass reducer bushing provided. To do this you should use a small coin to
hand tighten the reducer bushing to moderate tightness. Measure the
length of the bolt sticking out of your tripod where you are going to install
your new Leveling Base. It should stick up at least ¼ in (6mm) and be no
longer than 3/8 in (9.5mm), if the bolt is too long it must be shortened
(Acratech can do this for a minimal charge).
2) Being careful not to cross thread, slowly tighten your new leveling base
onto your tripod “firmly hand tight”.
3) After installing your new leveling base, CAREFULLY make sure that it is
not interfering or binding on any part of your tripod. IF ANY
INTERFERING OR BINDING OCCURS, REMOVE THE LEVELING BASE
AND CONTACT ACRATECH BEFORE CONTINUING.
Leveling Base installation continued:
4) Make sure the leveling base is installed tight enough so it will not loosen
during use.
5) Use the same procedure listed above to install your tripod head onto your
leveling base.
6) When using any tripod, tripod head, or quick release system you should
always “ test the set-up” by securely grasping the camera and trying to
move it left, right, up, down, forward, back, etc. to make sure everything is
tight and secure before removing your hands from your camera. This
should be done every time you put any camera on any tripod.
7) The Acratech Leveling base is equipped with special knobs that cannot
vibrate loose and fall off. Do not try to remove knobs or loosen past the
point where resistance is felt.
8) Care for your new leveling base:
Keep your new ball head clean and free from debris.
Clean using a damp cloth, water or rubbing alcohol can be used.
DO NOT USE OIL OR WD40 ON THE BALL.
When storing you ballhead for long periods of time,
the knobs should not be rmly tightened.
Thank you for choosing an Acratech product. If your Leveling Base or other
Acratech product needs service or repair please send it directly to Acratech. Do
not return it to your dealer. If you have any questions or comments please call
us at (909) 394-1802 or E-mail us at info@acratech.net
Especificaciones del producto
| Marca: | Acratech |
| Categoría: | Trípode |
| Modelo: | Leveling Base 1117 |
¿Necesitas ayuda?
Si necesitas ayuda con Acratech Leveling Base 1117 haz una pregunta a continuación y otros usuarios te responderán
Trípode Acratech Manuales
25 Agosto 2024
25 Agosto 2024
Trípode Manuales
- Trípode Sony
- Trípode Silvercrest
- Trípode Pyle
- Trípode Livoo
- Trípode Kodak
- Trípode Carson
- Trípode Easypix
- Trípode Hama
- Trípode Velleman
- Trípode AVerMedia
- Trípode Celestron
- Trípode DJI
- Trípode Vello
- Trípode Rollei
- Trípode Magnus
- Trípode Bresser
- Trípode Barska
- Trípode Zhiyun
- Trípode Miller
- Trípode Konig
- Trípode Benro
- Trípode GVM
- Trípode Vortex
- Trípode Marshall Electronics
- Trípode Sachtler
- Trípode Rode
- Trípode Sevenoak
- Trípode Laserliner
- Trípode Swarovski
- Trípode Celly
- Trípode Eurolite
- Trípode Drift
- Trípode Gitzo
- Trípode Proaim
- Trípode Testo
- Trípode Revo
- Trípode Konig & Meyer
- Trípode Manfrotto
- Trípode Velbon
- Trípode ARRI
- Trípode Ultimate Support
- Trípode Levenhuk
- Trípode JOBY
- Trípode Oben
- Trípode Dorr
- Trípode Glide Gear
- Trípode Winegard
- Trípode Libec
- Trípode Kogan
- Trípode MOZA
- Trípode Ulanzi
- Trípode Flycam
- Trípode Gravity
- Trípode Sirui
- Trípode Vinten
- Trípode Neewer
- Trípode ProMediaGear
- Trípode Ravelli
- Trípode Fidlock
- Trípode Mantona
- Trípode Olloclip
- Trípode Cullmann
- Trípode Vanguard
- Trípode IFootage
- Trípode SmallRig
- Trípode FeiYu-Tech
- Trípode FeiyuTech
- Trípode Sky-Watcher
- Trípode Hohem
- Trípode MOVE'N SEE
- Trípode On Air
- Trípode Kaiser Fototechnik
- Trípode Slidekamera
- Trípode IOptron
- Trípode FLOWCINE
- Trípode SteadiCam
- Trípode Fat Gecko
- Trípode 3 Legged Thing
- Trípode FLM
- Trípode Peak Design
- Trípode Easyrig
- Trípode Robus
- Trípode Studio Assets
- Trípode Square Jellyfish
- Trípode Stalco
- Trípode Tiltall
- Trípode E-Image
Últimos Trípode Manuales
26 Octubre 2024
25 Octubre 2024
17 Octubre 2024
8 Octubre 2024
3 Octubre 2024
2 Octubre 2024
2 Octubre 2024
1 Octubre 2024
24 Septiembre 2024
22 Septiembre 2024