ADDAC System ADDAC106 Manual de Usario

Lee a continuación 📖 el manual en español para ADDAC System ADDAC106 (5 páginas) en la categoría No categorizado. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/5
ADDAC106 T-NOISEWORKS USER’S GUIDE
March.2020Revision.01
Welcome to:
page 2ADDAC SYSTEM
OVERALL FEATURES
This is the last module in our T-Networks series, a straight forward 4 voice module with frequency and decay
controls for each of the voices. As the name already unveils we added a noise source and created 2 different
circuits that explores the timbre of a t-network when used to filter noise.
There are 2 different circuits in this module, voices 1 to 3 have a pre-vca t-network filter while in voice 4 the
t-networks filter applied post-vca.
At each voice input there’s a switch which sets which type of input to use, this signal will be used to control an
internal VCA hence why the type of setting defined here is important:
1. Trigger - Any incoming CV will be converted into a 1ms trigger as soon as it crosses it’s fixed threshold.
2. Mute - This disconnects then incoming signal effectivelly muting the voice.
3. Envelopes - This can be used with CV sources as well as Gate sources and simply follows the input signal.
This incoming signal will then be processed by a slew circuit which adds a decay factor allowing the user to set
the “Tail” of each voice.
Trigger mode is mostly dedicated for percussive sounds while the Envelope mode is open to any external enve-
lope control and able to control noise swooshes, swirls, crackles and pops simply out of t-networks filtered noise.
Audio inputs are also welcomed to be used as a Trigger/Envelope input, in fact the results of using this method
had us all extremelly surprised, so please do try it out!
Diferences between voices:
The first 3 voices also feature a Timbre selector switch: Hat/Snare
In Snare mode all frequencies coming from the t-networks filter pass thru to the output .
In Hat mode it adds a High Pass circuit which removes the mid/bottom frequencies (characteristic of the snare
strike) creating a higher spectrum output which is closer to a Hat timbre.
All of these 3 voices are also differently tuned from each other to offer more timbrical options.
Voice 4 is closer to a typical t-networks circuit but this time peculiar one where the noise is gated by the vca and
then sent through the t-networks filter.
Hat and Snare are terms used very looselly here, they are timbrical references and do not in any shape or form try
to effectivelly replicate the complex timbres of a real world Hat or Snare.
This module will also be available as a full DIY kit.
Features;
4 Voices each with:
Frequency control
Decay control
Timbre type, Hat/Snare (Voice 1 to 3)
Frequency Range Switch, Low/Mod/High (Voice 4)
Input
Audio Output
Also and overall Summing Mix output with Volume control and 2 diferent output types (Normal/Dirt)
Tech Specs:
4HP
4cm deep
40mA +12V
40mA -12V
CONTROLS DESCRIPTION
ADDAC106 User’s Guide
page 3ADDAC SYSTEM
T-Networks Frequency
Tune the Resonant Pitch for each
voice
Summing Mix Gain
Sets the output gain for the overall
summing mix
Independent voice input settings
Decay
Sets amount of decay
Hat/Snare switches
On/Off HP Filter
Summing Mix Output
Independent voices outputs
Independent voices inputs
Low/Mod/High range switches
Sets the Frequency Range

Especificaciones del producto

Marca: ADDAC System
Categoría: No categorizado
Modelo: ADDAC106

¿Necesitas ayuda?

Si necesitas ayuda con ADDAC System ADDAC106 haz una pregunta a continuación y otros usuarios te responderán




No categorizado ADDAC System Manuales

No categorizado Manuales

Últimos No categorizado Manuales