Air King 99532 Manual de Usario
Air King
Ventilator
99532
Lee a continuación 📖 el manual en español para Air King 99532 (8 páginas) en la categoría Ventilator. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
Oscillating Dimensions and Specications
99533 24” 14 1/2” 26 3/4” 120 60 3 3 Pedestal
99532 30” 14 1/2” 33 3/8” 120 60 3 3 Pedestal
2
Prop.
Model Dia. A B Volts Hz Speeds Blades Mounting Accessory
99533 24” 1025/880/480 1/4 5030 4320 2280 500/350/220 7.7/5.7/1.8 2.3/1.6/0.6 3.5
99532 30” 1010/860/530 1/4 7450 6090 3450 700/520/300 6.7/5.4/2.0 2.3/1.6/0.6 3.7
Prop. Motor CFM Air Velocity Sones @ Operating Full Load
Model Dia. RPM HP High Med Low @ 20 Ft. (FPM) 0.000SP Amps Amps
2
Operating Instructions & Parts Manual Models 99533, 99532
PLEASE READ AND SAVE THESE INSTRUCTIONS. Read carefully before attempting to assemble, install, operate or
maintain the product described. Protect yourself and others by observing all safety information. Failure to comply
with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
Description
Designed for cooling workers in factories, warehouses, manufacturing facilities and garages where
humid and demanding conditions exist. All circulator heads have high efciency corrosion resistant
propellers with steel blades. Circulator heads utilize a vertical tilt/locking adjustment for directional
ow. Wire guards are black power-coated steel and comply with OSHA Standard 1910.212 (1/2”
maximum opening). All circulator heads are oscillating that sweep through a 45 or 90 arc.° °
24” & 30” Quiet Design
Oscillating Pedestal Fan
Unpacking
1. Inspect for any damage that may have occurred during transit.
2. Shipping damage claim must be led with carrier.
3. Check all bolts, screws, setscrews, etc. for looseness that
may have occurred during transit. Retighten as needed.
Printed in U.S.A. New 5/11 5085460
A
1. Read all instructions before using Fan.
2. Make certain that the power source con-
forms to the electrical requirements of the
Fan.
3. Use this Fan only as described in this manual.
Any other use not recommended by the
manufacturer may cause re, electrical shock,
or injury to persons.
4. To reduce the risk of personal injury and elec-
tric shock, the Fan should not be played with
or placed where small children can reach it.
5. Unplug power cord before servicing, or
moving the Fan.
WARNING: DO NOT DEPEND UPON THE
ON-OFF SWITCH AS THE SOLE MEANS OF
DISCONNECTING POWER WHEN INSTALLING
OR SERVICING THE FAN. ALWAYS UNPLUG
THE POWER CORD.
6. This Fan must NOT be used in potentially
dangerous locations such as ammable,
e xp l o s i ve , ch e mi c a l - l a d e n or we t
a t mo spheres.
7. DO NOT use Fan in or near a window. Rain
may create an electrical hazard.
8. Completely reassemble Fan, according
to instructions, before reconnecting to
power supply.
9. The power cord is equipped with a three-
prong grounded plug that be inserted should
into a matching receptacle. Under no
circumstances should the grounding prong
be cut off the plug. Where a two-prong
wall receptacle is encountered, it must be
replaced with a properly grounded three-
prong receptacle installed in accordance
with the National Electrical Code (NEC) and
all applicable local codes and ordinances.
This work must be done only by a qualied
electrician, using copper wire only.
WARNING: USE OF A THREE-PRONG TO TWO-
PRONG ADAPTER IS NOT RECOMMENDED.
IMPROPER CONNECTION MAY CREATE THE
GENERAL SAFETY INFORMATION
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
re, electric shock and injury to
person, including the following:
RISK OF ELECTRICAL SHOCK. USE OF
SUCH ADAPTERS NOT PERMITTED IS
IN CANADA.
10. Where possible, avoid the use of
extension cords. If they must be used,
minimize the risk of overheating by
ensuring that they are UL listed. Never
use a single extension cord to operate
more than one Fan. Do not plug Fan
into any other cord connected device,
such as a power strip, cord reel, surge
protector, multiple outlet adapters or
outlet-type air fresheners. The use of
such devices may create a re hazard.
11. Do not operate any Fan with a
damaged cord or plug or after the
Fan malfunctions, has been dropped
or damaged in any manner. Return
Fan to authorized service facility for
examination, electrical or mechanical
adjustment or repair.
12. Do not insert or allow ngers or foreign
objects to enter any ventilation or
exhaust opening as it may cause an
electric shock or re, or damage the
Fan. Do not block or tamper with
the Fan in any manner while it is in
operation.
13.Locate the Power Cord so the Fan or
other objects are not resting on it. Do not
run Power Cord under carpeting or oor
mats. Do not cover Power Cord with
runners, or the like. Do not run Power
Cord through doorways, windows or
areas where cord impingement may
occur. Arrange Power Cord away from
room trafc and where it will not be
tripped over.
14.This Fan is not intended for use in
wet or damp locations. Never locate
a Fan where it may fall into water.
15. Do not use Fan outdoors.
16.This Fan is not suitable for use in
hazardous locations. Please refer to
National Electric Code (NEC) Article
500 or applicable state or local codes
or standards relating to electrical
requirements for Hazardous locations.
THIS FAN DOES NOT MEET THE
REQUIREMENTS OF NEC ARTICLE
500 (2008).
24” & 30” Quiet Design
Oscillating Pedestal Fan
2
WARNING: REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK – DO NOT USE THIS FAN
WITH ANY SOLID STATE SPEED CONTROL
DEVICES.
CAUTION: BECAUSE OF THE SIZE AND
WEIGHT OF THIS FAN, MAKE SURE ALL
PARTS ARE COMPLETELY ASSEMBLED
ACCORDING TO INSTRUCTIONS. FAILURE
TO DO SO COULD RESULT IN FAN
COMING APART DURING OPERATION
AND/OR PERSONAL INJURY.
Operating Instructions & Parts Manual 99533/99532
5085460New 5/11
3 5085460New 5/11
Locate remaining parts from Motor Hardware Bag
to Assemble Grills and Blade to the Motor.
1. Install the Rear Grill onto the Motor, lining up
the six holes in the grill with the six threaded
holes in the motor mounting ange. Install (6)
10-32 X 5/16” Hex Screws through the rear
grill into the grill mounting ange. Securely
tighten all (6) screws. (Figure 3)
2. Push the Fan Blade onto the Motor Shaft,
centering the Hub facing away from the
motor, until it stops against the shaft (Inset
A) . Align Square Head Bolt with at of the
motor shaft. TIGHTEN VERY SECURELY
WITH AN ADJUSTABLE WRENCH. Failure
to securely tighten the Bolt could result in
damage to the Fan and/or personal injury.
3. Hold the Front Grill so that the name, in the
center, is right side up and straight across.
Starting at the top: Fasten Front Grill to
Rear Grill by sliding the hooked wires on
the Front Grill over the outermost ring on
the Rear Grill. . The (Figure 4 / Detail A)
bottom most hooks will require the use of a
athead screwdriver to complete assembly.
Stand behind the Fan. Slip the at of the
screwdriver between the Front and Rear
Grills, next to one of the unfastened hooks.
(Figure 4 / Detail B) Pull screwdriver handle
upwards towards the Rear Grill. Slip the Front
Grill hook over the Rear Grill outer ring with
a push. Repeat procedure with remaining
hooks.
CAUTION: DO NOT BEND WIRES ON THE
FRONT OR THE REAR GRILLS.
GRILL AND BLADE ASSEMBLY
Figure 3
Inset A
Figure 4
Detail A
Detail B
COLUMN/MOTOR TO BASE/
ASSEMBLY
1. Rest Column and Motor Assembly on oor next
to the Base Assembly. Tilt Base Assembly up on
end. Pick up lower pipe of Column Assembly and
insert into the Mounting Flange. (Figure 2)
2. Loosen (2) 3/8-16 X 3/8” Allan Head Bolt in the
Mounting Flange. This will allow the Column to
settle in the bottom of the Base after setting the
Fan upright.
3. Tilt entire assembly to the upright position.
MAKE SURE BOLTS IN COLUMN AND
MOTOR ASSEMBLY STEPS ARE TIGHT
BEFORE STANDING FAN UPRIGHT.
4. Tighten the (2) 3/8-16 X 3/8” Allen Head Bolt in
the Mounting Flange.
Figure 2
Figure 1
Actual motor not shown for
detailed hardware view.
GRILL AND BLADE ASSEMBLY
CONTINUED
COLUMN AND MOTOR
ASSEMBLY
Locate Motor Hardware Bag to
Assemble Column and Motor Assembly.
1. Place at section on Upper Tube of Column
Assembly next to Neck on Motor Assembly.
Align the 1/2” diameter hole in the at section
on the Upper Tube ofColumn Assembly with
the 1/2” diameter hole in the Motor Assembly.
(Figure 1)
2. Insert the 1/2” X 1” Hex Bolt (3/4” head)
through the Motor Neck, and the Upper
Tube Assembly. Place 1/2” diameter Split
Lockwasher then the 1/2” diameter Hex Nut
(3/4” head) and tighten fully with a adjustable
wrench. (Figure 1)
3. From the same side of the Motor Neck,insert
one 1/4-20 X 1 5/8” Carriage Bolt through
the Arc-Shaped Slot in the Motor Neck and
Hole in the Upper Pipe of Column Assembly.
(Figure 1)
4. Attach pull string to motor speed switch, if
desired.
Especificaciones del producto
Marca: | Air King |
Categoría: | Ventilator |
Modelo: | 99532 |
¿Necesitas ayuda?
Si necesitas ayuda con Air King 99532 haz una pregunta a continuación y otros usuarios te responderán
Ventilator Air King Manuales
24 Agosto 2024
18 Agosto 2024
15 Agosto 2024
14 Agosto 2024
9 Agosto 2024
2 Agosto 2024
2 Agosto 2024
1 Agosto 2024
30 Julio 2024
28 Julio 2024
Ventilator Manuales
- Ventilator Bosch
- Ventilator Philips
- Ventilator BEKO
- Ventilator Delonghi
- Ventilator DeWalt
- Ventilator Honeywell
- Ventilator Inventum
- Ventilator JBL
- Ventilator Unold
- Ventilator Tefal
- Ventilator Alpina
- Ventilator Andrews
- Ventilator Ariete
- Ventilator OneConcept
- Ventilator Eurom
- Ventilator Orbegozo
- Ventilator EXCELLENT Electrics
- Ventilator Princess
- Ventilator Fisher And Paykel
- Ventilator Klarstein
- Ventilator Fagor
- Ventilator Silvercrest
- Ventilator Makita
- Ventilator Nedis
- Ventilator Korona
- Ventilator Black And Decker
- Ventilator Innoliving
- Ventilator Tristar
- Ventilator Domo
- Ventilator Vonroc
- Ventilator Rowenta
- Ventilator Tomado
- Ventilator Livoo
- Ventilator Stanley
- Ventilator SereneLife
- Ventilator Beurer
- Ventilator OK
- Ventilator Vox
- Ventilator Dyson
- Ventilator Bestron
- Ventilator Westinghouse
- Ventilator ECG
- Ventilator Izzy
- Ventilator Ryobi
- Ventilator Jata
- Ventilator LC-Power
- Ventilator Sharkoon
- Ventilator Melissa
- Ventilator Swan
- Ventilator Emerio
- Ventilator Scarlett
- Ventilator Taurus
- Ventilator Itho
- Ventilator Sencor
- Ventilator Midea
- Ventilator Blaupunkt
- Ventilator Frigidaire
- Ventilator Sunbeam
- Ventilator Thermaltake
- Ventilator Trust
- Ventilator Gemini
- Ventilator Tripp Lite
- Ventilator Heinner
- Ventilator Termozeta
- Ventilator Nabo
- Ventilator Defy
- Ventilator Infiniton
- Ventilator Bionaire
- Ventilator Lasko
- Ventilator Dimplex
- Ventilator DCG
- Ventilator BlueBuilt
- Ventilator Profile
- Ventilator Solis
- Ventilator Husqvarna
- Ventilator Evolar
- Ventilator Steba
- Ventilator Proline
- Ventilator Meaco
- Ventilator Ardes
- Ventilator Be Quiet!
- Ventilator Biltema
- Ventilator Soler And Palau
- Ventilator Everglades
- Ventilator Stadler Form
- Ventilator Bomann
- Ventilator Proficare
- Ventilator Cotech
- Ventilator Ufesa
- Ventilator CasaFan
- Ventilator Carrier
- Ventilator Trotec
- Ventilator Camry
- Ventilator Duux
- Ventilator Jocel
- Ventilator Gamma
- Ventilator Primo
- Ventilator Hunter
- Ventilator MPM
- Ventilator Hema
- Ventilator Tesy
- Ventilator Team
- Ventilator Vivax
- Ventilator Fantini Cosmi
- Ventilator Wahoo Fitness
- Ventilator Corsair
- Ventilator Fuave
- Ventilator Boneco
- Ventilator Kambrook
- Ventilator G3 Ferrari
- Ventilator Thermex
- Ventilator Tornado
- Ventilator Bimar
- Ventilator Superior
- Ventilator Kunft
- Ventilator Day
- Ventilator Master
- Ventilator Argoclima
- Ventilator Proklima
- Ventilator Eurolite
- Ventilator Heller
- Ventilator Vornado
- Ventilator Grunkel
- Ventilator Broan
- Ventilator Livington
- Ventilator ORNO
- Ventilator Weasy
- Ventilator Kalorik
- Ventilator Klarbach
- Ventilator Gamdias
- Ventilator Brandson
- Ventilator Schweigen
- Ventilator Duronic
- Ventilator SMC
- Ventilator Kogan
- Ventilator Portacool
- Ventilator Neo
- Ventilator Siku
- Ventilator XPower
- Ventilator Prem-i-air
- Ventilator Arcoaire
- Ventilator Djive
- Ventilator InnoGIO
- Ventilator Casablanca
- Ventilator Wallair
- Ventilator Envira-North
- Ventilator GoldAir
- Ventilator Canarm
- Ventilator Ravanson
- Ventilator SchwankAir
- Ventilator Fantech
- Ventilator RestantOutlet
- Ventilator Protector
- Ventilator Migros
- Ventilator Phaesun
- Ventilator NuTone
- Ventilator Omega Altise
- Ventilator Ebm-papst
- Ventilator Perfect Aire
- Ventilator Modern Fan Co.
- Ventilator Quorum International
Últimos Ventilator Manuales
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024