AmpliVox Executive SW505A Manual de Usario

AmpliVox No categorizado Executive SW505A

Lee a continuación 📖 el manual en español para AmpliVox Executive SW505A (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
4 1
3995 COMMERCIAL AVE., NORTHBROOK, IL 60062
AMPLIVOX PORTABLE SOUND SYSTEMS
PH. 800-267-5486 OR 847-498-9000
FX. 800-267-5489 OR 847-498-6691
WEB: WWW.AMPLI.COM
EMAIL: CUSTOMERSERVICE@AMPLI.COM
Made in USA
TRANSMITTER
MIC INPUT JACK
POWER ON INDICATOR
POWER ON/OFF SWITCH
CHANNEL SELECTOR SWITCH
1) Switch the Frequency Selector Switch to the desired channel (A or B).
2) Belt clip on the back of the unit clips the transmitter onto a belt or the
transmitter simply can be put into a pocket.
3) Plug the microphone into the Mic Input Jack.
4) The microphone can be clipped to a necktie or other clothing, using
the supplied clip. The lapel mic should be placed under the chin, as
close to the center of the body as possible
5) Slide the power ON/OFF switch to the ON position (the LED indicator
light will illuminate).
HELPFUL HINTS
A) If the selected channel is noisy, switch both the transmitter and
receiver to the other channel.
B) Low ceiling fluorescent lighting, overhead telephone lines, or close
proximity to metal fences can all cause static. If this occurs, try a
slight change of position and/or try changing frequencies.
WIRELESS MIC SET UP
The VHF wireless microphone system is compact, lightweight and
compatible with all AmpliVox VHF wireless systems. The wireless mic
operates in an authorized VHF band and has a useful range of up to 300-
ft. Each system operates on two crystal-controlled, switch selectable
frequencies for clear clean transmission.
“A” Channel “B” Channel
T6: 171.105 MHz T7: 171.845 MHz
The frequency appears on the back of each unit. Both transmitter and
receiver must have the same, and both units must be set to either “A” or
“B.” Note that two transmitters on the same frequency will not work with
one receiver. However two or more receivers will work with the same
transmitter. Before use, make certain you understand the function and
operation of the system.
RF INTERFERENCE
Please note that wireless frequencies are shared with other radio
services. According to the Federal Communications Commission
regulations, “Wireless microphone operations are unprotected
from interference from other licensed operations in the band. If any
interference is received by any Government or non-Government
operation, the wireless microphone must cease operation…” If you need
assistance with operation of frequency selection, please contact your
dealer or AmpliVox. Additionally There are models available for use in
Canada.
POWER SOURCE
The transmitter and receiver are each operated by a 9V alkaline battery.
Before use, install a battery as shown. Make certain the battery is fully
seated in its compartment so the cover slides in place easily. Battery life
with alkaline batteries is approximately 8 hours of operating time. The
receiver also features an external jack for connecting a 9V DC power
supply (not included).
TRANSMITTER OPERATION
If there is a “dead spot” in a room, try a slight change of position or try
changing frequencies. Each unit provides two selectable transmitting
frequencies.
9V DC ALKALINE
BATTERY
RIBBON FOR
BATTERY REMOVAL
BATTERY COVER
C) When the battery voltage drops below 6V, the LED indicator will
go out. This means you need a new battery.
D) Be sure to turn off the power whenever the units are not in use,
and remove the batteries if the units will be out of service for a
long time. NOTE: There are no user-adjustable parts inside the
transmitter or receiver Do not attempt to open or make any adjustments
E) Cellular telephones cause interference. Ask your audience to turn off
their cell phones.
BELT CLIP
A detachable belt clip is included for convenience. Slide the tapered
end of the belt clip into the grooved area located on the back of the unit
until it clicks into place.
PROBLEM SOLVING
FEEDBACK
Feedback is the howl or screech often heard in sound reinforcement
systems. It is caused by sound from the loudspeaker returning to the
microphone. AmpliVox systems utilize proven acoustical principles
to minimize this; however, there is no way to completely eliminate
feedback under conditions of high amplification. If feedback occurs
check the following:
1. User’s hand covering the head of the microphone. (Hold microphone
under head slots.)
2. Sound can easily re-enter microphone. Keep loudspeaker turned
toward audience. Note: sound can be reflected from a hard surface
back through the microphone. (Turn speaker.)
3. User holding microphone in a reflecting position. (Turn microphone.)
4. Volume setting too high. (Reduce microphone channel volume;
compensate by speaking louder or closer to the microphone.)
NO SOUND
Make sure amplifier POWER switch is turned on and red LED is lit. If
switch is on and LED is not lit, check to see that batteries are properly
connected and at full charge. If using optional power adapter, check to
see that front panel connector is properly seated, and verify that power
source is live.
IF YOU HAVE ANY QUESTIONS OR PROBLEMS PLEASE CALL OUR
CUSTOMER SERVICE DEPARTMENT AT 1-800-267-5486
Thank you for choosing the S505A and SW505A
Executive Adjustable Lectern from AmpliVox
Portable Sound Systems. Our system combines
flexibility with functionality. Please refer to this
user guide as you enjoy the unique capabilities of
another quality product from AmpliVox Portable
Sound Systems. As always, you can reach us at
800-267-5486, or at 847-489-9000, Monday -
Friday 8am - 6pm CST.
USER GUIDE
TABLE OF CONTENTS .................................................1
ASSEMBLY OF LECTERN (NO TOOL ASSEMBLY) ..2
CONTROL PANEL ........................................................3
WIRELESS MIC SETUP ..............................................4
PROBLEM SOLVING ..................................................4
NEED HELP?
CALL 800-267-5486
OR 847-498-9000
EMAIL:
CUSTOMERSERVICE@
AMPLI.COM
Made in USA
EXECUTIVE ADJUSTABLE SOUND COLUMN LECTERN S505A / SW505A
WHAT’S IN THE BOX?
NEVER RUN OUT OF
POWER GUARANTEE!
AMPLIFIER POWER SOURCES
(SOLD SEPARATELY)
10 D-CELL ALKALINE
BATTERIES FOR UP TO
200 HOURS TALK TIME
S1460 INTERNATIONAL
AC ADAPTER/RECHARGER
(110/240V; 50/60HZ)
S1465 NICAD
RECHARGEABLE BATTERY
PACK (REQUIRES S1460).
S505A
S805A Multimedia Stereo Amplifier
Dynamic XLR Microphone
15 foot XLR mic cable
Flexible Gooseneck with Shock
Mount Isolated Mic Holder
2 Built in Speakers
4 Neural Knobs/screws for
Reading Table 1" knob, 1" long
4 Neural Knobs for Base 2" long
Speaker Grille Cover
SW505A
SW805A Multimedia Stereo Amplifier
w/Internal Wireless Receiver
Dynamic XLR Microphone
15 foot XLR mic cable
Flexible Gooseneck with Shock
Mount Isolated Mic Holder
Wireless Mic and Transmitter
2 Built in Speakers
4 Neural Knobs/screws for
Reading Table 1" knob, 1" long
4 Neural Knobs for Base 2" long
Speaker Grille Cover
2 3
NEED HELP?
CALL 800-267-5486
OR 847-498-9000
EMAIL:
CUSTOMERSERVICE@
AMPLI.COM
NO TOOL ASSEMBLY OF LECTERN
SPEAKER COVER / AMPLIFIER
8. Remove and unpack the speaker cover.
9. Attach the speaker cover to the front of
the shroud by pushing the plastic posts in
each corner of the cover into the rubber
receptacles in the front of the shroud. See
figure 4 and 5.
Please read all instructions first and then follow the steps below:
BASE ASSEMBLY
1. Remove center column and shroud assembly from the shipping
carton and place as shipped (face down) on the floor or on a suitable
sturdy table.
2. Remove and unpack the base from the shipping carton.
3. Assemble the base to the column as shown in FIGURE 1 by using four
of the 2 inch long neural knob screws supplied with the lectern.
TIP: Do not completely tighten each screw as you place it through the
base and into the column. Wait until all four screws have been put into
the proper position and then tighten them up.
4. Turn the base and column assembly upright. If assembled on a table
place the unit upright on the floor.
READING TABLE ASSEMBLY
5. Remove and unpack the lectern reading table.
6. Attach the table to the top of the column. See FIGURE 2. This is
accomplished by placing the table top on the column base and lining
up the corners.
TIP: the corners need to be lined up in order to get the screws in the
table top.
7. Fasten the reading table to the colum with the 4 1 inch long neural
knob screws supplied. The knob screw goes up into the reading table
throught the 4 holes in the column (see ).FIGURE 2
FIGURE 1
FRONT VIEW
FIGURE 2
BASE
CENTER
COLUMN
READING
TABLE
CENTER
COLUMN
INSTALL NEURAL
KNOBS FROM
BASE INTO
COLUMN
THE CORNERS NEED TO
BE LINED UP IN ORDER
TO GET THE SCREWS IN
THE TABLE TOP.
10. Flush mount ampifier is built-in.
11. For an optional speaker installation (S1201) make sure the speaker
connection cable is routed through the proper notch in the back face of
the amplifier pocket of the shroud so that the table will not pinch the
cable when mounted. See .FIGURE 3
12. (SW505A) Make sure the antenna cable is also routed through the
notch in the same manner.
13. SW505A ONLY - Insert the small (2.5mm) plug into the amplifier
jack labeled ‘Antenna.’
14. See the amplifier operation manual for further instructions regarding
operation of the sound system.
OPERATION OF ADJUSTABLE LECTERN
This lectern adjusts from 39 inches to 45 inches measured from the
Amplifier side. To adjust the lectern height:
1. With one hand flat in the center of the table holding it down loosen
the adjustable height knob with the other hand.
2. You may extend the lectern up to its maximum height of 45 inches.
3. To lower the lectern, lightly press down on the reading table until the
desired height is reached and retighten the height-locking knob.
TIP: The knob locks at any height by tightening it. The lectern will adjust
from 45 inches down to 39 inches when measured from the amplifier
side.
ASSEMBLY OF FLEXIBLE GOOSENECK: (FIGURE 3)
To install the located 1. GOOSENECK onto the 2. MOUNTING FLANGE
by the far left corner of the desktop reading surface, first turn the neck
piece clockwise onto the mount. Next install the microphone holder (U
shaped piece) onto the end of the gooseneck by turning it clockwise
onto the top of the neck. You can then slide the 3. MICROPHONE into
the as shown. 4. MICROPHONE HOLDER
The 5. MIC CORD has a plug with three small holes in one end, A for
connecting with the microphone, and a ¼ in. male plug on the other
end, B for connecting with the unit on the control panel. Connect the
end with the three holes to the base of the microphone, and plug the
male ¼ in. end of the microphone cord into the jack labeled DYNAMIC.
The microphone has an ON/OFF switch . it should always be in the OFF
position until the main power is ON and you are ready to speak.
TO INSTALL OR REPLACE BATTERIES
Remove all cables and plugs from amplifier. Unscrew the thumb screws.
Pull carriage out to install new batteries, Insert 10 new Alkaline “D”
cell batteries, be sure to observe polarity, or replace with S1465 NiCad
battery pack. Carefully replace battery carriage. Reattach battery
door.
TIP:
Do not mix battery types or attempt to recharge alkaline batteries
- equipment damage, safety hazard or fire could result.
OPTIONAL POWER SUPPLY INSTALLATION
Optional Power Supplies may be substituted. Model S1460, International
AC Adapter/Recharger (110/220V, 50/60Hz). Model S1462, 12 Volt
DC adapter (automotive cigarette lighter plug-in). S1465 NiCad Battery
Pack.
5. MIC
CORD B
1. FLEXIBLE
GOOSENECK
4. SHOCKMOUNT MIC
HOLDER
2. MOUNTING
FLANGE
3. MICROPHONE
5. MIC CORD A
BASE
CENTER
COLUMN
READING
TABLE
TO OPERATE:
Plug microphone into DYNAMIC Microphone jack.
Plug straight end of 12” speaker cable into built in speaker jack and
right angle end into left SPEAKER jack on amplifier.
Turn Amplifier on (switch is located on the front of the amplifier). The
red light will go on, showing that power is available. Rotate VOLUME
control knob to obtain desired loudness level throughout the coverage
area.
MICROPHONE VOLUME
Controls the volume level of the microphones, including the wireless
microphones.
MICROPHONE INPUTS
There are three microphone inputs, which can be used
simultaneously:
DYNAMIC - for standard dynamic microphones 1/4 in.
CONDENSER - for electret or condenser microphones, which require
phantom power (supplied from the amplifier) 3.5mm
WIRELESS - accepts output from an external wireless microphone
receiver
AUXILIARY
The LINE IN provision is for connecting an external audio source such
as a CD player, tape player, MP3 player or computer sound card This
input also serves as a provision for connecting additional wireless
microphone receivers, audio mixers and other line level audio
sources.
Separate VOLUME and TONE control knobs allow flexibility in
controlling the sound quality as well as balancing the auxiliary source
with the microphones.
OUTPUT
The LINE OUT provision may be used for connecting to an input on
a recording device, such as a computer sound card, MP3 recorder,
tape recorder, or similar device. The LINE OUT can also be used
for a number of other applications, such as connecting to a house
system, or connecting to one of our wireless speaker transmitters,
for example.
INTERNAL SPEAKERS
The internal speakers are wired for stereo, LEFT and RIGHT channel
information is reproduced by the appropriate speaker inside the
unit.
EXTERNAL SPEAKERS
Two separately amplified speaker jacks allow you to use one or two
S1201, S1290, or any of our horn speakers for additional sound
power. Note: when using a stereo AUX source with a single speaker,
only one of the stereo channels will be heard. However, all MIC inputs
are heard equally on both channels.
IINTERNAL WIRELESS MICROPHONE RECEIVER *SW Model only*
Power ‘ON’ and ‘OFF’; Frequency ‘A’ and ‘B’ switches. Frequency
should match wireless transmitter. The red light above these switches
will come on when the wireless microphone receiver is active.
TONE L - SPEAKER - RVOLUMEDYNAMICVOLUME
1
WRLS 1
ON
LINE IN
WIRELESSCONDENSER
LINE OUT
ON
OFF
A
B
E X T E N D Y O U R V O I C E W I T H
1-800-267-5486
WWW.AMPLI.COM
MADE IN USA
ON
ON
OFF
AUX OUTDC IN
MAIN
32
POWER MICROPHONES AUXILIARY OUTPUT
MAIN
POWER
SWITCH
INTERNAL
WIRELESS MIC
RECEIVE RS
MASTER
VOLUME
MIC
INPUT
MIC
INPUT
MIC
INPUT
LINE IN
JACK
LINE OUT
JACK
SPEAKER
JACKS
TONE
CONTROL
AUXILIARY
VOLUME
POWER
INPUT
AUX
OUT
ON-OFF
When switch is in the ON position, the red light
will be on.
DC IN
Connection for optional adapter:
S1460 Universal AC Adapter (110/220V,
50/60Hz)
S1465 Nicad Battery Pack (requires S1460 AC
Adapter/recharger)
AUX OUT
Power source for 12 to 15V DC accessories.
S505A & SW505A CONTROL PANEL
AMPLIFIER
ADJUSTABLE
HEIGHT DIAL
USE TO ADJUST
LECTERN
HEIGHT FROM
39 TO 45 INCHES
STORAGE
SPAGE FOR
OPTIONAL
S1201
SPEAKERS
FIGURE 3
BATTERY PANEL
TO INSTALL
OR CHANGE
BATTERIES,
REMOVE THUMB
SCREWS AND
PULL OUT
CARRIAGE.

Especificaciones del producto

Marca: AmpliVox
Categoría: No categorizado
Modelo: Executive SW505A

¿Necesitas ayuda?

Si necesitas ayuda con AmpliVox Executive SW505A haz una pregunta a continuación y otros usuarios te responderán


No categorizado AmpliVox Manuales

AmpliVox

AmpliVox SN3230 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox Pinnacle SN3240 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox Elite SW355 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox SW660 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox SW632 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox SW662 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox Pinnacle ST3250 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox Presidential Plus S450 Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox Executive SW505A Manual de Usario

8 Septiembre 2024
AmpliVox

AmpliVox Presidential Plus SW450 Manual de Usario

8 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024