AMX MVP-WCS-52-GW Manual de Usario

AMX Cargador para dispositivo móvil MVP-WCS-52-GW

Lee a continuación 📖 el manual en español para AMX MVP-WCS-52-GW (2 páginas) en la categoría Cargador para dispositivo móvil. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Installation Guide
MVP-WCS-52 Wall Charging Station
Overview
The optional MVP-WCS-52 Wall Charging Station (FG5966-1X) offers the same
recharging and connection features for the MVP-5200i Touch Panel as the
MVP-TCS-52 Table Charging Station, with the advantage of being placed within
accessible locations where the table station is either inconvenient or impractical
(FIG. 1).
The MVP-WCS-52 is available in white (FG5966-13) or black (FG5966-12).
The features of the MVP-WCS-52 include:
• Full charging of a docked MVP-5200i in approximately 4.5 hours
• Touch panel password feature for security
• Integrated docking alignment guides for easy docking
Specifications
The MVP-5200i touch panel remains locked in the MVP-WCS-52 until unlocked
by the user. This may be done by entering an appropriate password (please refer
to the MVP-5200i User Manual, available from www.amx.com, for more
information), or by pressing the Security Release button on the front of the
device in emergencies. The station ejects the MVP-5200i device top first
(FIG. 2).
The device uses two neodymium rare-earth magnets to secure the MVP-5200i to
the cradle when the touch panel is angled forward.
Unlocking the Touch Panel
Once placed within the Wall Charging Station, the MVP-5200i remains secured
until the user unlocks it. To release the touch panel from the Wall Charging
Station:
1. Press the Security Release button.
2. A password keypad will pop up on the MVP-5200i screen. Enter a
password in the password keypad and press Enter.
3. Wait for the Wall Charging Station to pivot the touch panel away from the
wall.
4. The device will remain in the ejected position until the MVP-5200i is
removed. Wait until the device’s ejection door has completely withdrawn
before re-installing the MVP-5200i.
Recharging
To recharge the MVP-5200i:
1. Slide the device into the Wall Charging Station cradle bottom-first and
make sure the device is fully seated in the Charging Station.
2. Press the top of the MVP-5200i back until it clicks. The touch panel is now
locked into the Charging Station, and the station will automatically charge
the device’s battery.
3. To release the touch panel, press the Security Release button, enter the
password (if activated), and wait for the Wall Charging Station to pivot the
touch panel away from the wall.
FIG. 1 MVP-WCS-52-GB Wall Charging Station - Front
MVP-WCS-52 Specifications
Dimensions (HWD): • 8.88" x 6.38" x 2.19" (22.54 cm x 16.19 cm x 5.56 cm)
Note: Always use the cutout/installation dimensions for
the MVP-WCS-52 when installing this unit into various
surfaces. This SP engineering drawing is available online
at www.amx.com.
Power Requirements: • 1.7A @ 12 VDC (Class II listed power supplemented)
Startup Power
Requirements: • Total: 1.7A
• Charging: 1.1A
• Ejection: 0.6A
Weight: • Without back box: 0.85 lbs (0.39 kg)
• With back box: 1.30 lbs (0.59 kg)
Front Panel
Components: • Securing Magnets: Secures MVP touch panel during
ejection.
• Security Latch: Adds the primary layer of security when
mounting an MVP touch panel. When the device is
inserted, this latch grabs onto the rear of the touch panel
and secures it to prevent it from inadvertently being
removed.
• Interface Connector Pins: A set of retractable pins (male)
that connect to the underside MVP connector strip. This
connection provides both communication and power
between the touch panel and the MVP-WCS-52.
• Support Cradle: This retractable mechanism supports a
resting MVP panel and allows a user to either insert or
remove a connected MVP panel.
• Security Release pushbutton: Located on the front of the
unit, this pushbutton toggles an on-screen security
keypad if security is enabled.
- Entering the correct release code allows the MVP-WCS-
52 to release the touch panel from the security latch.
Operating/Storage
Environments: • Operating Temperature: 0° C to 40° C (32° F to104° F)
• Operating Humidity: 20% - 85% RH
• Storage Temperature: -20° C to 60° C (-4° F to140° F)
• Storage Humidity: 5% - 85% RH
Security Release
MVP-5200i-GB
MVP-WCS-52
button
MVP-WCS-52 Specifications (Cont.)
Included
Accessories • MVP-WCS-52 Wall Charging Station Quick Start Guide
( )93-5966-12
• Wallmount Plastic Back Box (EMA5966-13)
• MVP-WCS-52 Installation Kit - Black (KA5966-01bl)
• MVP-WCS-52 Installation Kit - White (KA 5966-01wh)
• MVP-WCS-52 Wall Charging Station Template
( )68-5966-01
Other AMX
Equipment: • MVP-TCS-52 Table Charging Station (FG5966-1X)
• Wallmount Metal Rough-In Box (62-5966-12)
• PSN4.4 (FG423-45)
• PSN6.5 (FG423-41)
• MVP-5200i - Gloss Black (FG5966-01)
• MVP-5200i - Gloss White (FG5966-02)
FIG. 2 MVP-WCS-52-GW Wall Charging Station - Side View
MVP-5200i
Wall Charging Station
Security Release button
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
3/11
©2011 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-5966-12 REV: F
Installing the MVP-WCS-52
Since the Wall Charging Station is intended to be affixed to a wall or other
permanent structure, care must be taken to ensure its proper installation to
prevent potential damage to the MVP-5200i placed within. The device may be
installed into existing walls, but the optional metal rough-in box must be
installed before installation of drywall or other paneling.
Note: Other than wall installation tools, the only tool required for this installation
is a #1 Phillips screwdriver.
Installing the Wall Charging Station and Plastic Back Box
The Plastic Back Box has two knockouts at the top of the box and four (4)
lockdown wings attached to the box with Phillips-head screws. For ease of
installation, the interior of the box contains an "UP" arrow pointing to the
knockouts.
Note: The optional Metal Rough-In Box is not required for installation of the
supplied Plastic Back Box, but it offers an extra level of support.
To install the Plastic Back Box:
1. Cut a hole into the wall or surface intended to hold the back box. The
back box is sized 8.375 inches (21.27cm) long and 5.75 inches (14.60cm)
high. Use the included MVP-WCS-52 Wall Charging Station Template
(68-5966-01) as an aid for hole placement and measurement.
WARNING: Make sure to measure the size of the intended hole before starting
to cut it. Cutting the hole slightly smaller than the dimensions to allow for
adjustments is highly recommended.
2. Select the knockout to be removed from the top of the back box. The box
has two knockouts, at the top left and the top right.
Note: To assist with wiring, and to avoid mechanical stresses on the wire and
the mechanism of the Wall Charging Station, the top right knockout is preferred
for use.
3. Run the power cable through the knockout into the back box. Pull out
about six inches (15.25cm) of cable into the back box to facilitate
installation of the MVP-WCS-52.
4. Slide the plastic back box into the hole, being careful not to twist or pinch
the cable, and set it flush with the wall. Make sure that all of the lockdown
wings are folded into their slots before attempting to insert the box. For
ease of installation, the inside of the box has the direction "UP" labeled for
reference.
5. Extend the wings on the sides of the back box by tightening the screws
inside the box, taking care not to overtighten. Not all of the wings must be
extended to lock the back box in place, but extending a minimum of two
wings on opposite sides of the box is highly recommended. Apply enough
pressure to the screw head to keep the box flush with the wall: this
ensures that the wing will tighten up against the inside of the wall.
WARNING: Make absolutely certain that the back box is in its intended
position. Once the back box lockdown wings are extended, removing the back
box will be extremely difficult without damaging the wall in the process.
6. Prepare the captive wires for the 2-pin 3.55 mm mini-captive wire
connector used for the MVP-WCS-52’s power supply:
• Strip 0.25 inch (6.35 mm) of wire insulation off all wires.
• Insert each wire into the appropriate opening on the connector.
• Turn the screws clockwise to secure the wires in the connector. Do not
over-torque the screws; doing so can bend the seating pins and damage
the connector.
7. Secure the power cable to the device, using either of the two tie-wrap
anchors included in the Installation Kit at the top rear of the device
(FIG. 3). Point the head of each tie wrap toward the center of the device.
8. Firmly seat the mini-captive wire connector to the power connector on the
device.
9. Firmly seat the device against the back box. Make sure that the tab con-
nector at the top of the device is locked into the back box.
10. Insert the two installation screws from the MVP-WCS-52 Installation Kit
into the screw holes in the interior compartment of the device and tighten
them to anchor the device to the back box.
Note: For ease of installation, put each screw on a neodymium magnet in the
device’s interior compartment to keep them on hand until they are needed.
11. Take a rubber foot and remove its adhesive backing. Put the foot, adhe-
sive-side down, in the slot surrounding the screw hole in the Wall Charg-
ing Station. Press down firmly to remove any air bubbles from underneath
the foot.
12. Install an MVP-5200i device by placing it into the interior compartment
bottom-first. Press the top of the touch panel until it is flush with the Wall
Charging Station. The neodymium magnets will hold it in place.
13. To remove the MVP-5200i, unlock the touch panel and wait for the touch
panel to pull away from the Wall Charging Station. Once it has been
released, grip it by the top of the device, and pull it free from the Charging
Station.
Installing the Optional Metal Rough-In Box
The optional Metal Rough-In Box (FG037-11) is 10 inches (25.40cm) wide at its
widest dimension (wider than the bezel of the Wall Charging Station), and is
only intended for pre construction installations (FIG. 4). The Metal Rough-In
Box is used in conjunction with the Wall Charging Station’s plastic back box.
The Metal Rough-In Box must be located behind 3/8" (0.95cm) to 3/4" (1.91cm)
of wall/mounting surface material.
The Metal Rough-In Box bears a wing on each corner which is intended to
bridge gaps between studs and/or spacers. These wings may be bent carefully
in order to fit a particular gap, but may not be so bent as to allow the rough-in
box to hang in a vertical position. Once placed in the desired position, put at
least one screw through each wing into the adjoining stud or spacer to secure
it.
The interior of the rough-in box contains a set of holes on either side, as well as
top and bottom, for standard 1/4-inch screws. Use these holes to anchor the
rough-in box to its adjoining studs or spacers.
WARNING: Ensure that the metal rough-in box is flush with the 2x4 studs. Any
overhang will affect the installation of the covering sheetrock, as well as affect
the placement of the plastic back box.
The rough-in box has two sets of knockouts in the top and bottom, one in the
set for US wiring and one for international wiring.
Note: Make sure that the power cable has been pulled through the metal
rough-in box by the resident electrician before continuing the installation.
After completing the installation of the metal rough-in box, install sheet rock or
other wall material over the box, cut a hole matching the size of the inside
diameter in the sheet rock, and clean out all dust before proceeding with the
installation of the Wall Charging Station.
Additional Information
For additional installation information, please refer to the MVP-5200i Modero
ViewPoint Touch Panel User Manual, available online at www.amx.com.
FIG. 3 MVP-WCS-52 - Rear View Of Anchors And Connector Plug
FIG. 4 Typical Optional Metal Rough-In Box Installation
Tie-Wrap Anchors
Mini-Captive Wire
Connector Plug
(female)
Install front surface of rough-in
box flush with surface of wall stud

Especificaciones del producto

Marca: AMX
Categoría: Cargador para dispositivo móvil
Modelo: MVP-WCS-52-GW

¿Necesitas ayuda?

Si necesitas ayuda con AMX MVP-WCS-52-GW haz una pregunta a continuación y otros usuarios te responderán


Cargador para dispositivo móvil AMX Manuales

AMX

AMX MVP-TDS-9 Manual de Usario

8 Septiembre 2024
AMX

AMX MVP-WCS-52-GW Manual de Usario

8 Septiembre 2024
AMX

AMX MIO-RCC-KIT Manual de Usario

8 Septiembre 2024
AMX

AMX MVP-TCS-52 Manual de Usario

8 Septiembre 2024
AMX

AMX MVP-TCS-52-GW Manual de Usario

8 Septiembre 2024

Cargador para dispositivo móvil Manuales

Últimos Cargador para dispositivo móvil Manuales

Tripp Lite

Tripp Lite CSC32USBW Manual de Usario

20 Octubre 2024
Anker

Anker PowerCore+ 20100 USB-C Manual de Usario

16 Octubre 2024
Bauhn

Bauhn ACRWC-0424-M Manual de Usario

15 Octubre 2024
Bauhn

Bauhn AFTC3-0424-W Manual de Usario

15 Octubre 2024
Bauhn

Bauhn AFTC3-0424-B Manual de Usario

15 Octubre 2024
Bauhn

Bauhn ACRWC-0424-W Manual de Usario

15 Octubre 2024
Bauhn

Bauhn ADMWC-0224 Manual de Usario

15 Octubre 2024
Black Box

Black Box Deluxe UCCSM-10-30TP-HASP Manual de Usario

13 Octubre 2024
Trust

Trust 90W Notebook Power Adapter Manual de Usario

11 Octubre 2024
Black Box

Black Box Deluxe UCCSL-12-36HP Manual de Usario

10 Octubre 2024