Anthro MiniCart Manual de Usario

Anthro Oficina MiniCart

Lee a continuación 📖 el manual en español para Anthro MiniCart (2 páginas) en la categoría Oficina. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

TECHNOLOGY FURNITURE®

Anthro MiniCart

Assembly Instructions

01– Insert Screws ............................ Qty. 4 325-5052-00 ....................

02– 2 3/8” Non-Locking Casters ........ Qty. 2 150-5002-03 ................... *

03– Caster Inserts ........................... Qty. 4 525-1000-00 .................... *

04– 2 3/8” Locking Casters ................ Qty. 2 150-5003-03 .................. *

05– 1.75” Large End Caps ................ Qty. 2 175-5021-xx ......................

06– Base Tube Screws ............................. Qty. 3 .....................325-5000-00

07– MiniCart Base Tube ................... Qty. 1 125-5004-xx .....................

08– Self-threading Screws ...................Qty. 6 325-5010-00 ......................

09– Vertical Legs ............................ Qty. 3 .................................................

23.875” Vertical Legs (GT23xx) ...... ................................. 125-5020-xx

Enclosed Parts List

Detailed views of all hardware is provided with each

assembly step.

10– 1-5/8” Screws ....................................Qty. 6 325-5086-00 .....................

11– Shelf Supports ...................................Qty. 6 175-5060-xx ......................

12– Shelf Clamps ......................................Qty. 6 175-5059-xx ....................

13– MiniCart Shelves ....................... Qty. 2 100-6003-xx ......................

14– 1.5” Small End Caps .................. Qty. 3 175-5020-xx ......................

All fastener quantities listed here are the minimum needed for your

cart assembly. Your shipment may include a few extras.

Cable Management Components

Cable Alley, 9” Qty 1 175-5061-03 ...................... .............................................

Cable Alley, 3” Qty 1 175-5062-03 ...................... .............................................

Cord Handler Qty 1 175-5001-03 ........................ .............................................

Self-threading Screws...... Qty 6 325-5010-00 ..............................................

Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062

SAVE THESE INSTRUCTIONS! Document # 300-5068-00

Step 7

Install all four caster inserts into the base tube and secure

(fully tighten) with one Caster Insert Screw per insert.

Next, push the casters, (locking ones in front) into the caster

inserts.

Step 8

Carefully rotate the shelf assembly , upside down (from Step 6)

as shown.

Place the base tube assembly onto the vertical (from Step 7)

legs of the shelf assembly.

Attach the base tube to each leg using a total of three

3-1/2” Bolts.

Tighten all Self-threading and Base Tube Screws.

Step 9

Rotate your MiniCart over onto the casters.

Pop the three 1.5” small end caps into the vertical legs and

the two 1.75” large end caps into the base tube.

After you add your equipment to the cart, select the cable

management components that suit.

To install the Cable Alleys, expand each sleeve and ﬁt it over

a cart leg. Align the mounting hole(s) in the sleeve with the

holes on the leg, then install with self-threading screws.

To install the Cord Handler, snap the large end around any

cart leg, then route cables through the small end.

Congratulations! Your MiniCart assembly is complete.

Please return the enclosed Registration Card to receive our

product updates, new catalogs, and sale ﬂyers.

Thank you for choosing Anthro!

January 2015, Rev D

These Assembly Instructions are for

the GT23xx.

Before beginning assembly of your

Anthro MiniCart, please take a moment to

review the parts list below to verify that

your shipment is complete.

Does your Cart have 4” Casters?*

Then these are your casters:

4” Locking Caster

150-5011-03

4” Non-Locking Caster

150-5010-03

Questions? 1-800-325-3841

04 06

03 02

1.5” Small End Cap

1.75” Large End Cap

3-1/2” Bolt

325-500 0-00

TOOLS

To make the assembly of your cart even

easier, we have included all of the required

tools . Use the handy Hex Driver Bit in your

electric drill in place of the Hex Driver.

Hex Driver 5/32”.................. 375-5000-00

Hex Driver Bit 5/32” 375-5003-00 ...........

8 oz. Rubber Mallet............ 375-5022-00

1/2” Caster Insert Screw

325-505 2-00

Locking Casters

Anthro MiniCart

Assembly Instructions

Anthro® Corporation Technology Furniture® 10450 SW Manhasset Drive Tualatin, Oregon 97062

Step 1

Before proceeding, please review the Assembly Instructions

of all Anthro products you purchased and are planning to

include in this installation.

Step 3

Attach three shelf supports to each shelf.

Begin by ﬁrst installing a shelf clamp into the shelf notch.

Be sure the pointed barbs face towards the outer shelf

edge.

Next, slide a shelf support into the recesses of the shelf

clamp and shelf. Push in as far as possible.

Finally, secure with a 1-5/8” Clamp Screw (325-5086-00).

anthro.com

Step 4

Loosely attach one shelf to hole 14 from the bottom (coped end)

of one vertical leg using a Self-threading Screw. These fasteners

are cutting threads into the leg, so the ﬁrst few turns will require

some force.

NOTE: This will place your lower shelf 22” from the ﬂoor using the

standard 2 3/8” casters.

Step 5

Loosely attach the remaining shelf to hole 2 from the top

(non-coped end) (from Step 4) of the vertical leg assembly

using one Self-threading Screw.

NOTE: Handle the shelf assembly carefully until the cart is fully

assembled.

Step 6

Loosely attach the 2nd and 3rd vertical legs to the shelf

assembly using one Self-threading Screw per (from Step 5)

shelf support.

TIP: Use the holes in the vertical legs as a ruler to ensure that

your Self-threading Screws are installed into the correct

locations.

Questions? 1-800-325-3841

First

Finally

Barbs

Step 2

Decide on the shelf locations for your MiniCart. You can

place your shelves almost anywhere on the vertical legs (the

legs are stamped at 1” increments).

For a lower shelf location that is higher or lower than

19” from the ﬂoor, refer to the illustrations shown at right to

determine which holes to attach your lower shelf.

Once your MiniCart is assembled, it’ll take a little effort to

remove and reinstall it. Measure, measure, measure.

NOTE: These instructions will place your lower shelf 19” from

the ﬂoor using the standard 2 3/8” casters.

GT23xx with 2 3/8” Casters

GT23xx4 with 4” Casters

Hole 12=20”

Hole 11=19” (measured from the coped end)

Hole 10=18”

Hole 11=20”

Hole 10=19”

Hole 9=18”

REMINDER: You may want to

measure your equipment to make

sure it ﬁts between the selected

shelf locations and adjust your

assembly as needed

Coped end

19”

GT23xx

Overall MiniCart height is

28” using 2 3/8” casters

NOTE: Add 1” to overall height for 4” casters and subtract 3” from

overall height for glides.

Bottom

(coped)

end

Hole 14=22”

(using 2 3/8” Casters)

Insert one Self-threading Screw

through each Shelf Support

Top

(non-coped)

end Hole 2

Top

(non-coped)

end

Bottom

(coped)

end

NOTE: These Instructions will create

approximately 6” of usable space

between your shelves.

Lower Shelf

Self-threading Screw

325-5 0-0001

Self-threading Screw

325-5 0-0001

Self-threading Screw

325-5 0-0001

1-5/8" Screw

325-5086-00

Especificaciones del producto

Marca:	Anthro
Categoría:	Oficina
Modelo:	MiniCart
Tipo de operación:	Draaiknop
Color del producto:	Zwart
Pantalla incorporada:	Nee
Peso.:	4400 g
Ancho:	375 mm
Profundidad:	355 mm
Altura:	137 mm
Número de funciones:	1
Longitud del cable:	0.7 m
Ancho del embalaje:	234 mm
Empaquetadura en profundidad:	393 mm
Altura del embalaje:	390 mm
Manual de usuario:	Ja
Material de la carcasa:	Aluminium, Stainless steel
Tipo de material (arriba):	Rooster + bakplaat
Número de quemadores/zonas de cocción:	1 zone(s)
Fácil de limpiar:	Ja
Activos:	1450 W
Temporizador integrado:	Nee
Ajustable en altura:	Nee
Función incorporada:	Ja
factor vorm:	Rechthoekig
Almacenamiento de cable:	Ja
País de origen:	China
Luz indicadora:	Nee
Piezas aptas para lavavajillas:	Ja
Termostato ajustable:	Ja
Pies antideslizantes:	Ja
Medidor de temperatura central:	Nee
Número de programas de cocina:	1
Certificados de sostenibilidad:	CE, UKCA
Número de posiciones:	1
Cumplimiento de la sostenibilidad:	Ja
Libro de recetas:	Ja
Recubrimiento antiadherente:	Ja
Tapa:	Ja
Número de personas:	6 persoon/personen
Superficie para hornear (BXD):	233 x 355 mm
Material de la superficie de cocción:	Aluminium
Material laminar:	Aluminium
Indicador de temperatura lista:	Nee
Altura del paquete principal (exterior):	420 mm
Ancho del embalaje principal (exterior):	235 mm
Peso bruto del embalaje principal (exterior):	8000 g
Longitud del paquete principal (exterior):	415 mm
Cantidad por caja principal (exterior):	1 stuk(s)
Peso bruto del palet:	160000 g
Productos por palet:	20 stuk(s)
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz
Altura bruta del palet:	1050 mm
Raza de ganado de paleta:	1000 mm
Longitud bruta del palet:	1200 mm
Temperatura de cocción (máx.):	260 °C
Productos por capa de palet:	10 stuk(s)
La ley por palet:	2 stuk(s)
Número de paquetes principales (exteriores) por palet:	20 stuk(s)
Funciones de la tapa:	Detachable lid, Hinged lid
Elemento calefactor extraíble:	Nee
Placas removibles:	Ja
Número de platos/gradillas:	1
Recubrimiento kookoppervlak:	Keramisch
Período de garantía:	2 jaar
Superficie de la parrilla:	827 cm²
Plato para gofres incluido:	Nee
Adecuado para uso en campamentos:	Nee
Sin humo:	Nee
Modo congelador:	Nee