Aquasure AS-D100MCB Manual de Usario

Lee a continuación 📖 el manual en español para Aquasure AS-D100MCB (1 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
STEP 1. Remove Aerator from faucet on which lter
will be installed.
STEP 2. Determine the type of threads on your
faucet
STEP 3. Screw the diverter valve onto the faucet,
turning the swivel collar to tighten
STEP 4. Turn on water and rotate lever
External Threads: No adapter should be needed.
Internal Threads: Through trial and error, select the proper
adapter and washer to screw into faucet and tighten
manually.
Make certain that gasket (already installed in diverter valve)
is positioned securely between the diverter valve and the
faucet (or adapter). Rotate diverter valve stem to desired
positions. Swivel collar may need to be re-tightened. Place
assembly conveniently next to sink.
This causes the water to ow through thelter before exiting
the faucet. To stop water ow to lter, rotate the lever back to
turn water off.
STEP 5. Connecting the lter replacement indicator
circuit plug
After making sure the faucet adapter are connected properly,
connect the two pin circuit plug to activate the lter replacement
timer.
The LED in front of the system will blink a few times indicating
that the timer has been activated.
SYSTEM START-UP
Once the system has been connected, activate the systems lter cartridges by running water through the system for 3 - 5
minutes.
Immediately check entire water ltration system for leaks. If you notice any leaks, turn off the faucet and x the leak.
Upon rst use, you may notice some carbon nes. This is normal and will disappear during the 3 - 5 minute lter cartridge
activation.
Note:
The included adapters are designed to t most faucets. To create a tight seal, you may
need to use the gasket from your faucet’s aerator in addition to the washers included with
the adapters. If the adapters do not t, consult your local plumbing or hardware supplier
for assistance in obtaining the correct thread adapter.
To avoid damage to diverter valve nish cover with a rag if using pliers to tighten collar.
A drinking water cartridge may contain carbon nes (Very ne black powder). After
installation, ush the cartridge for 5 minutes to remove the nes before using the water.
It is recommended that you run the tap at least 20 seconds prior to using water for
drinking or cooking purposes.
During initial use, your water may appear cloudy. This cloudiness is caused by air that
has been trapped in the cartridge. If you let the water sit for 5 minutes in a glass, you will
notice the cloudiness disappear from the bottom up. This phenomenon is not harmful.
CAUTION! If installing the unit in new construction, ensure that house plumbing is
ushed thoroughly before opening the water supply valve.
DASH SERIES COUNTERTOP SYSTEM INSTALLATION INSTRUCTION
STEP 1. OPEN SYSTEM
Remove cover and band
STEP 2. FLIP SYSTEM
Flip system and place in
small bucket
STEP 3. UNSCREW HOUSING
Remove cover and band
STEP 4. REPLACE FILTER
Replace with new lter
STEP 5. SCREW HOUSING
Screw back housing
STEP 6. UNPLUG BATTERY
Unplug battery connector
STEP 7. UNSCREW & REPLACE
Unscrew battery case and replace
battery
STEP 9. FLIP OVER & CLOSE
Flip system and replace band
and cover
STEP 10. SYSTEM START-UP
Repeat system start-up and
ushing steps.
STEP 8. SCREW & PLUG
Screw back battery case
and plug battery connector
FILTER REPLACEMENT INSTRUCTIONS
AQUASURE DASH SERIES
Tel: 1-800-661-0680
www.AQUASUREUSA.com
You can also visit us online for system installation tutorial and support.
http://www.aquasureusa.com/support

Especificaciones del producto

Marca: Aquasure
Categoría: No categorizado
Modelo: AS-D100MCB

¿Necesitas ayuda?

Si necesitas ayuda con Aquasure AS-D100MCB haz una pregunta a continuación y otros usuarios te responderán




No categorizado Aquasure Manuales

No categorizado Manuales

Últimos No categorizado Manuales