Argo AEI1G65EMX3PH Manual de Usario

Argo Varios controles climáticos AEI1G65EMX3PH

Lee a continuación 📖 el manual en español para Argo AEI1G65EMX3PH (60 páginas) en la categoría Varios controles climáticos. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/60

INSTALLATION INSTRUCTIONS •

ISTRUZIONI D’INSTALLAZIONE

NOTICE D’INSTALLATION •

INSTALLATIONSANLEITUNGEN

INSTRUCCIONES DE INSTALACION •

INSTRUÇÕES DE INSTALAÇÃO

OODDHHGGIIEESS TTOOPPOOQQEETTHHSSHHSS

37.4255.124.01 02/2017

Split air conditioner system •

Condizionatore d’aria split system

Climatiseurs split •

Split-klimagerät

Acondicionador de aire de consola partida sistema split •

Aparelho de ar condicionado-Sistema Split

ΔΙΑΙΡΟΥΜΕΝΕΣ ΜΟΝΑΔΕΣ ΚΛΙΜΑΣΜΟΥ

AEI1G65EMX

AEI1G65EMX3PH GR

IMPORTANT!

Please read before installation

This air conditioning system meets strict safety and operating

standards.

For the installer or service person, it is important to install or

service the system so that it operates safely and efficiently.

For safe installation and trouble-free operation, you must:

• Carefully read this instruction booklet before beginning.

• Follow each installation or repair step exactly as shown.

• Observe all local, state and national electrical codes.

• Pay close attention to all warning and caution notices given in

this manual.

•The unit must be supplied with a dedicated electrical line.

This symbol refers to a hazard or unsafe practice which can result

in severe personal injury or death.

This symbol refers to a hazard or unsafe practice which can result

in personal injury or product or property damage.

If necessary, get help

These instructions are all you need for most installation sites and

maintenance conditions.

If you require help for a special problem, contact our sale/service

outlet or your certified dealer for additional instructions.

In case of improper installation

The manufacturer shall in no way be responsible for improper

installation or maintenance service, including failure to follow the

instructions in this document.

SPECIAL PRECAUTIONS

• During installation, connect before the refrigerant system and

then the wiring one; proceed in the reverse orden when removing

the units.

When wiring

ELECTRICAL SHOCK CAN CAUSE SEVERE

PERSONAL INJURY OR DEATH. ONLYA QUALIFIED,

EXPERIENCED ELECTRICIANS SHOULD ATTEMPT

TO WIRE THIS SYSTEM.

• Do not supply power to the unit until all wiring and tubing are

completed or reconnected and checked, to ensure the grounding.

• Highly dangerous electrical voltages are used in this system.

Carefully refer to the wiring diagram and these instructions when

wiring.

Improper connections and inadequate grounding can cause

accidental injury and death.

•Ground the unit following local electrical codes.

• The Yellow/Green wire cannot be used for any connection

different from the ground connection.

• Connect all wiring tightly. Loose wiring may cause overheating

at connection points and a possible fire hazard.

• Do not allow wiring to touch the refrigerant tubing, compressor,

or any moving parts of the fan.

• Do not use multi-core cable when wiring the power supply and

control lines. Use separate cables for each type of line.

When transporting

Be careful when picking up and moving the indoor and outdoor

units. Get a partner to help, and bend your knees when lifting to

reduce strain on your back. Sharp edges or thin aluminium fins on

the air conditioner can cut your fingers.

When installing...

... In a ceiling or wall

Make sure the ceiling/wall is strong enough to hold the unit-weight.

It may be necessary to build a strong wooden or metal frame to

provide added support.

... In a room

Properly insulate any tubing run inside a room to prevent

"sweating", which can cause dripping and water damage to walls

and floors.

... In moist or uneven locations

Use a raised concrete base to provide a solid level foundation for

the outdoor unit.

This prevents damage and abnormal vibrations.

... In area with strong winds

Securely anchor the outdoor unit down with bolts and a metal

frame. Provide a suitable air baffle.

... In a snowy area (for heat pump-type systems)

Install the outdoor unit on a raised platform that is higher than

drifting snow. Provide snow vents.

When connecting refrigerant tubing

• Keep all tubing runs as short as possible.

• Use the flare method for connecting tubing.

• Apply refrigerant lubricant to the matching surfaces of the flare

and union tubes before connecting them; screw by hand and

then tighten the nut with a torque wrench for a leak-free

connection.

• Check carefully for leaks before starting the test run.

NOTE:

Depending on the system type, liquid and gas lines may be either

narrow or wide. Therefore, to avoid confusion, the refrigerant

tubing for your particular model is specified as narrow tube for

liquid, wide tube for gas.

When servicing

• Turn the power OFF at the main power board before opening

the unit to check or repair electrical parts and wiring.

• Keep your fingers and clothing away from any moving parts.

• Clean up the site after the work, remembering to check that no

metal scraps or bits of wiring have been left inside the unit being

serviced.

• Ventilate the room during the installation or testing the

refrigeration system; make sure that, after the installation, no gas

leaks are present, because this could produce toxic gas and

dangerous if in contact with flames or heat-sources.

WARNING

CAUTION

WARNING

Installation site selection

AVOID

• Heat sources, exhaust fans.

• Direct sunlight.

• Damp, humid or uneven locations.

• To make holes in areas where electrical wiring or conduits

are located.

• Choose places as cool as possible and well ventilated.

• use lug bolts or equal to bolt down the unit, reducing

vibration and noise.

Provide a solid base for outdoor unit raised from the ground

level. Fix unit to base using 4 anchor bolts.

10 cm

40 cm

SYSTEM WIRING DIAGRAM

2 INDOOR UNITS

1 INDOOR UNIT

1 PHASE

Especificaciones del producto

Marca:	Argo
Categoría:	Varios controles climáticos
Modelo:	AEI1G65EMX3PH
Tipo de operación:	Knoppen
Color del producto:	Zwart
Peso.:	3701 g
Ancho:	274 mm
Profundidad:	437.8 mm
Altura:	43.9 mm
Peso del embalaje:	4749 g
Ancho del embalaje:	495 mm
Empaquetadura en profundidad:	170 mm
Altura del embalaje:	100 mm
Material de la carcasa:	Metaal
País de origen:	China
Puerto(s) VGA (D-Sub):	1
Consumo de energía (máx.):	33 W
HDCP:	Ja
Velocidad máxima de actualización:	30 Hz
Número de puertos de entrada HDMI:	1
Número de DisplayPorts:	1
Voltaje de entrada:	100 - 240 V
Conector de 3,5 mm:	Ja
Temperatura de almacenamiento:	-20 - 60 °C
Frecuencia:	50 - 60 Hz
Cantidad de puertos RJ-45:	1
Puertos de salida RJ-45:	1
Versión HDCP:	1.4/2.2
Número de puertos de salida HDMI:	9
Temperatura de funcionamiento (TT):	-1 - 44 °C
Humedad relativa de funcionamiento (VV):	20 - 90 procent
Resoluciones escaladas:	3840 x 2160
Conector RS-232/422:	Ja