Arlec Luxor CH206 Manual de Usario

Arlec Calentador Luxor CH206

Lee a continuación 📖 el manual en español para Arlec Luxor CH206 (3 páginas) en la categoría Calentador. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

1. Read all instructions before using this heater.

2. This heater is hot when in use.

To avoid burns, do not let bare skin touch hot

surfaces.

Use handles when moving this heater.

Keep combustible material such as drapery

and other furnishings, at least 1 metre from

the heater.

When in use keep the mains cord of the heater

away from touching the heater body. Do not

drape the cord over the heater while hot.

Extreme caution is necessary when any

heater is used by or near children or invalids

and whenever the heater is left operating

unattended.

3. Always unplug heater when not in use.

4. Do not operate any heater with a damaged

cord or plug or after the heater malfunctions,

has been dropped or damaged in any manner.

Return heater to suitably qualiﬁed facility

for examination, electrical or mechanical

adjustment or repair.

5. Do not use outdoors, the product is designed

only for household use.

6. Never locate heater where it may fall into a

bathtub or other water container.

7. Do not run cord under carpeting.

Do not cover cord with throw rugs runners, or

the like. Keep cord away from traf ﬁc areas to

avoid tripping over.

8. To disconnect heater, turn controls to off, then

remove plug from outlet.

9. Connect to properly earthed socket-outlet of

the appropriate voltage.

10. Do not insert or allow foreign objects to enter

any ventilation or exhaust opening as this may

cause an electric shock or ﬁre, or damage the

heater.

11. To prevent a possible ﬁre, do not block the

grilles in any manner.

12. Do not use in areas where petrol, paint, or

ﬂammable liquids are used or stored.

13. Use the heater only as described in this

manual. Any other use not recommended by

the manufacturer may cause ﬁre, electric

shock, or injury.

14. Do not connect via double adapters or power

boards. Avoid the use of an extension cord

because the extension cord may overheat

and cause risk of ﬁre. However, if this heater

is used with an extension cord, use as short

a cord as practical.

15. Do not use this appliance with a programmer,

timer or any other device that switches

the heater on automatically, since a ﬁre

risk exists if the appliance is covered or

positioned incorrectly.

16. In order to avoid overheating, do not cover

the heater.

17. To eliminate a choking hazard for young

children, remove and safely discard the

protective cover ﬁtted to the power plug of

this heater along with all packaging material

and promotional labels.

18. Fully unwind the cord before ﬁrst time use

19. There are no user serviceable parts in this

heater; any maintenance other than cleaning

should be performed by an authorised service

representative.

20. The installation of a residual current device

(safety switch) is recommended to provide

additional safety protection using electrical

appliances. It is advisable that a safety switch

with a rated residual operating current not

exceeding 30mA be installed in the electrical

circuit supplying power to the appliance. See

your electrician for professional advice.

21. Keep these instructions handy for future

reference.

CPIN002296/3

2000W

convection HeAteR

WITH TImer and Turbo fan

Luxor

User ManUal

FOR PERSONAL INDOOR USE ONLY

CH206

WARNING!

To Reduce The RIsk of fIRe, elecTRIc shock,

oR peRsoNAl INjuRy, ReAd, uNdeRsTANd

ANd folloW INsTRucTIoNs befoRe

usING ThIs heATeR

Keep this manual in a safe place for future reference

CPIN002296/3

Model ceh206

Max Heating Power 2000W max

Rated Frequency 50hz

Rated Voltage 220-240V ~

TechNIcAl specIfIcATIoNs

For all Sales & Warranty enquiries

Arlec Australia Pty. Ltd. ACN 009 322 105

(“Arlec”) gives the Warranty.

Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130

Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130

Customer Service: (03) 9982 5111

New Zealand Toll Free: 0800 003 329

Email: custservice@arlec.com.au

Arlec guarantees this product in accordance with the Australian

Consumer Law.

Arlec also warrants to the original ﬁrst purchaser of this product

(“you”) from a retailer that this product will be free of defects

in materials and workmanship for a period of 12 months from

the date of purchase; provided the product is not used other

than for the purpose, or in a manner not within the scope of the

recommendations and limitations, speciﬁed by Arlec, is new and

not damaged at the time of purchase, has not been subjected

to abuse, misuse, neglect or damage, has not been modiﬁed or

repaired without the approval of Arlec and has not been used for

commercial purposes (“Warranty”).

If you wish to claim on the Warranty, you must, at your own

expense, return the product, and provide proof of original purchase

and your name, address and telephone number, to Arlec at the

address below or the retailer from whom you originally purchased

the product within 12 months from the date of purchase.

Arlec will (or authorise the retailer to) assess any claim you may

make on the Warranty in the above manner and if, in Arlec’s

reasonable opinion, the Warranty applies, Arlec will at its own

option and expense (or authorise the retailer to) replace the

product with the same or similar product or repair the product and

return it to you or refund the price you paid for the product. Arlec

will bear its own expenses of doing those things, and you must bear

any other expenses of claiming on the Warranty.

The Warranty is in addition to other rights and remedies you may

have under a law in relation to the product to which the Warranty

relates.

Our goods come with guarantees that cannot be excluded under

the Australian Consumer Law. You are entitled to a replacement

or refund for a major failure and for compensation for any other

reasonably foreseeable loss or damage. You are also entitled

to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major

failure.

WARRANTy

IMpoRTANT sAfeGuARds

CH206_CPIN002296-3.indd 5-1 8/11/13 3:55 PM

IDENTIFICATION

USER MANUAL

i. POWER CONTROL KNOB

With the power control knob to position “o” the heating element is off. When the rotary

knob is set to • the heater power is 750W (low range). When the knob is set to •• the heater

power is 1250 (mid range). When the knob is set to ••• the heater power is 2000 (high range)

ii. TURBO FAN SWITCH

The heater is equipped with a Fan which helps to distribute heat in the room. The fan draws

some of the convection heat from inside of the unit and blows it from the front turbo fan

outlet grille. The heater can be used with or without the fan which is selected by the switch

on the front of the heater body.

iii. THERMOSTAT SWITCH

The rotary knob is to regulate the heat in order to maintain a desired temperature. When

the room temperature is lower than the temperature setting on the knob, the heater will

function and heat up the room until the desire temperature is at tained. When the ambient

temperature reaches the set temperature, heat setting will be turned off automatically.

Turn the knob more clockwise for higher heat settings.

iv. TIMER CONTROL

The heater will be always On when the slide switch is in “On” position (I).

The heater will be always off when the slide switch is in “Off” position (O).

The heater will be controlled by the times set on the timer when the slide switch is

in TIMER position

To set the timer, rotate the clock dial clockwise, until the current time is aligned with

the indicator arrow at the centre. When you wish the heater to switch ON, push the

corresponding time segment outwards from the centre. Each segment represents

around 15 minutes. For example, if you want the heater continuously ON for 2 hours,

push 8 segments outwards the centre face.

CPIN002296/3

The heater must always be used with feet assembled and in

upright position. At tach the feet to the heater body in the order

given below:

i. Place the convector heater on a ﬂat desk or carton.

ii. Locate the feet in position, make sure the mounting holes

on the leg mounts align with the ﬁxing holes on the heater

body. Make sure the leg mount with the cord entry slot is

attached at the mains cord end.

iii. Using 4 screws for each feet attachment secured the feet

to the heater body.

ASSEMBLY

Fasten feet with

supplied screws

2000W

convection

HeAteR

WITH TImer and Turbo fan

› ‹Luxor

CH206 Convection Heater with Turbo Fan is equipped with three heat set tings and a thermostat

to ensure your precise heating needs are met. In addition the heater has a fan turbo option

which assists with circulating warm air through your room

Hot Air Outlet

Timer

Control

Turbo Fan Switch

Turbo Fan

Air Outlet FeetAir Inlet

Power Control

Knob

Thermostat

Knob

MAINTENANCE & CLEANING

i. Before cleaning, turn off the heater, unplug the power cord and allow the

heater to cool.

ii. Do not immerse cord, plug or heater into water or other liquid or pour water

or other liquid over the heater.

iii. Use a vacuum cleaner to remove dust and dirt from air openings.

iv. Clean exterior surfaces using a solution of water and mild detergent with wrung out

damp sponge. Use and wring out the damp sponge and wipe the exterior surface again.

Finally wipe with a dry cloth. Allow sufﬁcient time to dry before plugging electrical cord

into outlet.

v. Any other servicing should be performed by an authorized service representative.

Do not use the heater if it has malfunctioned or become damaged in any way.

OPERATION

CAUTION: There may be some odour coming from the heater for the very ﬁrst time you use this

heater. This is normal during the break-in period or after long term storage. Make sure the heater

is in well ventilated area and continue running it until the smell goes away.

Before First Use

Remove all the packaging material along with any promotional material. Unwind the cord to its

full length and place the heater on a ﬁrm level surface in a stable, upright position.

Visually inspect p2-he air inlets and outlets to ensure that there are no blockages.

• Set the power control knobs to off position.

• Plug the heater into a 10 amp wall socket

• Ensure the heater is on a ﬂat surface

• Set the power to desired position Low, Medium or High range. Check the time setting and

adjust it to the desired time setting. Turn the thermostat knob until the heater turns on .The

power on led above the knob will glow. Slowly turn the thermostat knob anti clockwise until

the heater shuts off. The heater will automatically maintain this temperature. For a lower

temperature rotate the knob further anti clockwise. For higher temperature, rotate the knob

clockwise.

• Select the fan as desired.

NOTE: If operated at the Low heat setting, the heater will not provide as much heat output

as in the High heat setting, however the low setting will not require as much electrical

power to operate. To avoid overloading a circuit, do not plug the heater into a circuit that

already has other appliances working. When the heater is not in use switch off and unplug.

IMPORTANT SAFEGUARDS

CAUTION

• This heater is to be operated only in upright position.

• When the heater is not in use, store in a cool dry location.

• Do not store until the heater cools down.

WARNING

• This appliance is not intended for use by young children or inﬁrm persons unless

they have been adequately supervised by a responsible person to ensure that

they can use the appliance safely.

• Young Children should be supervised to ensure that they do not play

with the appliance.

• The heater must not be located in front of a socket outlet.

• Do not use this heater in the immediate surroundings of a bath, shower

or swimming pool.

HELPFUL ADVISE BERFORE USE

• Please retain all packaging until you have checked and counted all the parts and the

contents of the ﬁxing pack against the parts list.

• The ﬁxing pack contains small items which should be kept away from young children.

• We suggest that you open the ﬁxing pack and place all the contents into a container,

therefore reducing the risk of losing any small pieces.

CH206_CPIN002296-3.indd 2-4 8/11/13 3:55 PM

Especificaciones del producto

Marca:	Arlec
Categoría:	Calentador
Modelo:	Luxor CH206
Colocación del dispositivo:	Ingebouwd
Tipo de operación:	Touch
Color del producto:	Zwart
Pantalla incorporada:	Nee
Temporizador:	Ja
Peso.:	8500 g
Ancho:	590 mm
Profundidad:	520 mm
Altura:	- mm
Bloqueo infantil:	Ja
Peso del embalaje:	9500 g
Ancho del embalaje:	670 mm
Empaquetadura en profundidad:	570 mm
Tipo de material (arriba):	Glaskeramiek
Potencia quemador/zona de cocción 2:	1800 W
Potencia quemador/zona de cocción 3:	1800 W
Potencia quemador/zona de cocción 1:	1200 W
Número de quemadores/zonas de cocción:	4 zone(s)
tipo de placa:	Inductiekookplaat zones
Quemador/zona de cocción tipo 1:	Sudderen
Quemador/zona de cocción tipo 2:	Regulier
Tipo de quemador/zona de cocción 3:	Regulier
Número de quemadores de gas:	0 zone(s)
Número de zonas de cocción electrónicas:	4 zone(s)
Quemador normal/zona de cocción:	1400 W
Posición de control:	Boven voorzijde
Ancho del compartimento de instalación:	560 mm
Profundidad del compartimento de instalación:	490 mm
Interruptor encendido / apagado:	Ja
Apagado automático:	Ja
Altura bajo encimera:	25 mm
Tipo de quemador/zona de cocción 4:	Sudderen
Potencia quemador/zona de cocción 4:	1200 W
Fuente de alimentación quemador/zona de cocción 1:	Electrisch
Fuente de alimentación quemador/zona de cocción 2:	Electrisch
Fuente de alimentación quemador/zona de cocción 3:	Electrisch
Fuente de alimentación del quemador/zona de cocción 4:	Electrisch
Posición del quemador/zona de cocción 1:	Links achter
Posición quemador/zona de cocción 2:	Links voor
Posición quemador/zona de cocción 3:	Rechts achter
Posición del quemador/zona de cocción 4:	Rechts voor
Forma zona de cocción 1:	Rond
Forma zona de cocción 2:	Rond
Forma zona de cocción 3:	Rond
Forma zona de cocción 4:	Rond
voltaje-de-entrada-de-CA:	220 - 240 V
Frecuencia-de-entrada-de-CA:	50 Hz