Audiovox RCR412BN Manual de Usario

Audiovox Mando a distancia RCR412BN

Lee a continuación 📖 el manual en español para Audiovox RCR412BN (4 páginas) en la categoría Mando a distancia. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Battery Saver

Your universal remote control saves battery power by

automatically turning off if any key is pressed for more than

60 seconds. This saves your battery life should your remote

get stuck in a place where the keys remain depressed, such as

between sofa cushions.

Universal Remote Control

Owner’s Manual

RCR412BN / RCR412SN / RCR412SIN

Manual del Propietario (parte posterior)

SAVE THIS MANUAL AND THE CODE LISTS!

Remote controls can sometimes lose their programming

when you change the batteries. Make sure you keep the

manual and code lists in a safe place so that you can

reprogram the remote if you need to.

Tip: This remote is already programmed to operate

most RCA-branded TVs, VCRs, DVD players and satellite

receivers. Just press the corresponding key—DVD for

a DVD player, TV for a television, SAT•CBL•DTC for a

satellite receiver, VCR•AUX for a VCR.

Your universal remote requires two alkaline batteries AA

(batteries may or may not be included, depending on model).

To install the batteries:

1. Remove the battery compartment

cover.

2. Insert the batteries, matching the

batteries to the (+) and (–) marks

inside the battery compartment.

3. Push the battery cover back into place.

Battery Precautions:

• Do not mix old and new batteries.

• Do not mix alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries.

• Always remove old, weak or worn-out batteries promptly

and recycle or dispose of them in accordance with Local

and National Regulations.

To use this universal remote with your home entertainment

system, ﬁrst you need to program it to control your devices.

There are four ways you can program the universal remote to

operate your devices:

• The Auto Code Search goes automatically through all the

codes for the device you’re trying to control. It’s the easiest

method, but it can sometimes take longer than some of the

other programming methods.

• The Brand Code Search searches through the codes for

select brands of devices. It’s not as easy as the auto code

search, but it can be faster.

• The Direct Code Entry lets you enter a code from the

accompanying code list for your brand of device. It’s not as

easy as the other methods, but it’s potentially the fastest

method.

• The Manual Code Search lets you manually go through

all the codes for the device you’re trying to control.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote. If

some device features don’t work, go to next step to try a

different code.

2. Repeat the Auto Code Search Method from the beginning.

When your device turns off, do not stop searching.

Instead, with the unit now off, continue to press the PLAY

key every 5 seconds until the unit turns back on.

3. Once the unit turns back on, press the REVERSE key on the

remote every 2 seconds until your device turns off again.

When your device turns off again, press the STOP key.

4. Test the key’s functionality again by attempting to control

a variety of the device’s functions. If the code that has

been stored controls the majority of the device’s functions,

programming is complete. If the code stored does not give

maximum functionality, try another code.

Auto Code Search

The Auto Code Search goes automatically through all the

codes for the device you’re trying to control. When you nd

the one that operates your device, you can stop the search and

store that code.

1. Manually turn on the device you

want to control.

2. Press and hold the device key you want to program. While

you’re holding down the device key, use your other hand

to press and hold the remote’s key at the same ON•OFF

time.

3. Wait until the ON•OFF key comes on and stays on. Then

release both keys.

4. Point the remote directly at the

front panel of the device you

want to control. Press PLAY on

the remote and wait 5 seconds.

The remote is testing a batch of

10 codes on your device.

Did your device turn off?

YES: Go to step .5

NO: Press PLAY again. The remote tests the next batch of

10 codes.

Keep pressing PLAY every 5 seconds until your device

turns off.

5. When your device turns off, press

the REVERSE key on the remote

and wait at least 2 seconds.

The remote tries the last of the

previous ten codes.

Did your device turn on?

YES: Press the STOP key. You’re

done! You’ve programmed this

device key.

NO: Press REVERSE again. The remote tests the next

code in the batch.

Keep pressing REVERSE every 2 seconds until your device

turns back on. When it does, press STOP.

Note: If you accidentally press the REVERSE key after your

device turns on, press the FORWARD key. Then, wait two

seconds to see if your device turns off again.

NOTES

Throughout the programming of each key, be sure to keep

the remote pointed at the IR sensor of the device you are

currently programming the remote to control.

Test the remote with the device to make sure the

device key is programmed with the correct code for

maximum functionality. If some features don’t work, try

a different code. See the “Testing the Code for Maximum

Functionality” section below for more information.

During the Auto Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the ON•OFF key

blinks four times and turns off, and the last programmed

code under that device key is retained).

The ON•OFF key blinks four times and turns off when the

remote has gone through all the codes. The remote exits

the Auto Code Search. If your device hasn’t turned off yet,

try a different search method.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote. If

some device features don’t work, go to the next step to try

a different code.

2. Repeat the Brand Code Search from the beginning. When

the device turns off for the ﬁrst time, don’t press the STOP

key, which would store the same code. Instead, with the

unit now off, continue to press the key repeatedly ON•OFF

until the unit turns back on.

3. Once the unit turns back on, you have found another code

that operates the device. Press the STOP key.

4. Test the key’s functionality again by attempting to control

a variety of the device’s functions. If the code that has

been stored controls the majority of the device’s functions,

programming is complete. If the code stored does not give

maximum functionality, try another code.

Brand Code Search

The Brand Code Search goes through only the codes for one of

the select brands listed in the accompanying code list. If your

brand of device is listed, this search can be very quick and easy.

TIPS: Each device key is associated with a type of device—

the TV is preset to search for TVs, SAT•CBL•DTC for satellite

receivers, cable boxes or digital TV converters, DVD for

DVD players, and VCR•AUX for VCRs or DVRs. To program

a device key for a different type of device, see the Changing

a Key’s Device Type section.

The ON•OFF key serves as an indicator light during

programming, giving you feedback at each stage of the

process.

To exit without saving a new code at any point in the Brand

Code Search, press the key.GO BACK

1. Manually turn on the device you

want to control.

3. Press and hold the device key you want to program. While

you’re holding down the device key, use your other hand

to press and hold the remote’s ON•OFF key at the same

time.

4. Wait until the ON•OFF key comes on and stays on. Then

release both keys.

6. Point the remote directly at the

front panel of the device you want

to control. Press ON•OFF on the

remote and wait 2 seconds. The

remote is testing a single code for

your device’s brand.

Did your device turn off?

YES: Press the STOP key to store the code. You’re done!

You’ve programmed this device key.

NO: Press ON•OFF again. The remote tests the next code

for your brand.

Keep pressing ON•OFF every 2 seconds until your device

turns back on. When it does, press STOP.

2. Find your device’s brand in the

Brand Code list section of the

accompanying code list. Circle

the number for your brand and

keep the list handy.

Co d e L i ts

Li s ta de Có di g os

2 3

5 6

789

VCR

2 3

5 6

789

DVD

SA / C ABLE

2 3

5 6

789

2 3

5 6

789

5. Look at the number you circled for

your device’s brand code number.

Press that number on the remote

keypad.

NOTES

Throughout the programming of each key, be sure to keep

the remote pointed at the IR sensor of the device you are

currently programming the remote to control.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different

code. See the “Testing the Code for Maximum Functionality”

section below for more information.

During the Brand Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the ON•OFF key

blinks four times and turns off, and the last programmed

code under that device key is retained).

The ON•OFF key blinks four times and turns off when the

remote has gone through all the codes. The remote exits the

Brand Code Search. If your device hasn’t turned off yet, try a

different search method.

Direct Code Entry

Direct Code Entry lets you enter a code from the accompanying

code list for your brand of device. It’s not as easy as the other

methods, but it’s potentially the fastest method.

1. Manually turn on the device you

want to control.

3. Press and hold the device key you want to program (the

ON•OFF key comes on).

While you’re holding down the device key, use your other

hand enter the ﬁrst ﬁve-digit code for your brand in the

code list (the ON•OFF key goes off after the rst digit).

2. Find the Code List that came with

the remote. Locate the section for

the type of device you’re trying to

program, and ﬁnd your brand in

that section. Circle the codes for

your brand and keep them handy.

Co d e L is ts

Li s ta de Có di g os

2 3

5 6

789

VCR

2 3

5 6

789

DVD

SA C LE

2 3

5 6

789

2 3

5 6

789

NOTES

Remember to enter the code for future reference in the box

provided in the Code Retrieval section of this manual.

If your brand isn’t listed in the code list, use one of the Code

Search methods to program the remote control. (Refer to the

Auto and Manual Code Search methods.)

If you release the device key any time during the Direct Code

Entry procedure, the ON•OFF key blinks four times, and

the process is exited. The last programmed code under the

device key is retained.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different code

in the list.

4. When you’ve nished entering the ve-digit code, keep

holding down the device key and look at the ON•OFF key.

 IstheON•OFFkeyon?

YES: You’re done! You’ve programmed this device key.

 NO,itblinkedfourtimesandturnedoff:You have

either entered a code number that is not in the code lists or

missed a step in the code entry procedure. Try step 3 again.

Manual Code Search

The Manual Code Search lets you go one-by-one through all

the codes for the device you’re trying to control. When you nd

the one that operates your device, you can stop the search and

store that code.

TIPS: The ON•OFF key serves as an indicator light during

programming, giving you feedback at each stage of the process.

Each device key is associated with a type of device—the TV is

preset to search for TVs, SAT•CBL•DTC for satellite receivers,

cable boxes or digital TV converters, DVD for DVD players,

and VCR•AUX for VCRs or DVRs. To program a device key for

a different type of device, see the Changing a Key’s Device

Type section.

The Manual Code Search method may take a long time

because the remote searches through all of the codes in

its memory one-by-one. If your brand is listed in the Brand

Codes or the Code Lists, rst try the Brand Code Search or

the Direct Code Entry method.

To exit without saving a new code at any point in the Manual

Code Search, press the GO BACK key.

Step 1: Install your batteries

Step 2: Program your remote

TIP: Each device key is associated with a type of device—the

TV is preset to search for TVs, SAT•CBL•DTC for satellite

receivers, cable boxes or digital TV converters, DVD for DVD

players, and VCR•AUX for VCRs and DVRs. To program a

device key for a different type of device, see the Changing a

Key’s Device Type section.

The ON•OFF key serves as an indicator light during

programming, giving you feedback at each stage of the

process.

TIPS: Each device key is associated with a type of device—

the TV is preset to search for TVs, SAT•CBL•DTC for satellite

receivers, cable boxes or digital TV converters, DVD for

DVD players, and VCR•AUX for VCRs or DVRs. To program

a device key for a different type of device, see the Changing

a Key’s Device Type section.

To exit without saving a new code at any point in the Auto

Code Search, press the key.GO BACK

In most cases, the keys on

this remote perform the same

functions as the keys on your

original remotes once you’ve

programmed this remote to

operate your components.

Many keys on this remote

have other functions as well.

Illuminated key ON•OFF

serves as an indicator light to

provide feedback.

Device keys ( , TV

SAT•CBL•DTC DVD, ,

VCR•AUX) put the remote in

the right mode to control your

device.

Backlight key ( ) turns

backlighting on/off.

GUIDE MENU and put the

remote in menu/guide mode,

which makes the CH/VOL

keys serve as arrow keys;

they also access the same

features as the keys on your

original remotes.

CH VOL and keys have dual

functions: they can act as

navigation keys in menu

systems as well as channel

and volume controllers

outside the menus. The

CH keys also provide skip

forward and skip back control

for DVD players and DVRs

that support this functionality.

Care and Maintenance

• Keep the remote dry. If it gets wet, wipe it dry immediately.

• Use and store the remote only in normal temperature

environments.

• Handle the remote gently and carefully. Don’t drop it.

• Keep the remote away from dust and dirt.

• Wipe the remote with a damp cloth occasionally to keep it

looking new.

• Modifying or tampering with the remote’s internal devices can

cause malfunction and invalidate its warranty.

1. Manually turn on the device you

want to control.

3. Wait until the ON•OFF key comes on and stays on. Then

release both keys.

4. Point the remote directly at the front panel of the device you

want to control. Press ON•OFF on the remote and wait 2

seconds. The remote is testing a single code for your device.

Did your device turn off?

Press the STOP key to store YES:

the code. You’re done! You’ve

programmed this device key.

NO: Press ON•OFF again. The

remote tests the next code for

your device.

Keep pressing ON•OFF every 2

seconds until your device turns back

on. When it does, press STOP.

TIP: Because there are so many codes, you may have to press

the ON•OFF key many times—possibly hundreds of times.

NOTES

Throughout the programming of each key, keep the remote

pointed at the IR sensor of the device you are programming

the remote to control.

Test the remote with the device to make sure the device

key is programmed with the correct code for maximum

functionality. If some features don’t work, try a different

code. See the “Testing the Code for Maximum Functionality”

section below for more information.

During the Manual Code Search, the remote ignores

keypresses that aren’t part of the search.

The search times out after two minutes (the ON•OFF key

blinks four times and turns off, and the last programmed

code under that device key is retained).

The blinks four times and turns off when the ON•OFF key

remote has gone through all the codes. The remote exits the

Manual Code Search. If your device hasn’t turned off yet, try

a different search method.

Testing the Code for Maximum Functionality

1. Try a variety of the device’s functions with the remote. If

some features of your devices don’t work, go to the next

step to try a different code.

2. Repeat the Manual Code Search from the beginning. When

the device turns off for the ﬁrst time, don’t press the STOP

key, which would store the same code. Instead, with the

unit now off, continue to press the key repeatedly ON•OFF

until the unit turns back on.

3. Once the unit turns back on, you have found another code

that operates the device. Press the STOP key.

4. Test the key’s functionality again by trying a variety of

functions. If the code controls the majority of the device’s

functions, programming is complete. If the code stored

does not give maximum functionality, try another code.

Code Retrieval

Once you’ve programmed the remote to control your devices,

you may want to record the codes for future reference. If

you used the Direct Code Entry method, this is easy. Just

ﬁnd the codes you entered and make a note of them in the

boxes below. If you used one of the Code Search methods to

program your remote or if you used the Direct Entry method

but don’t remember the code, you will need to retrieve each

device’s ﬁve-digit code. Retrieving the actual code and writing

it down will save you time if you ever need to program the

remote again (e.g., if programming is lost when you change

the batteries). If the codes are recorded, you can use the

Direct Entry method to reprogram your remote to control your

devices, which is quick and easy.

1. Press and hold the device

key (TV, SAT•CBL•DTC, DVD,

VCR•AUX) whose code you

wish to retrieve. The ON•OFF

key turns on. Keep pressing the

device key.

IMPORTANT

Because this remote controls more than one device, you

must rst “tell” the remote which device you wish to

operate. That means, if you wish to operate your TV, you

must rst press the TV key to put the remote in the TV

Mode. The remote stays in that device mode until you press

a different device key. For example, if your remote is in TV

Mode and you want to operate the DVD player, you must

press the key to change device modes.DVD

Accessing Device Menus and Guides

Many devices use on-screen menus and guides to help you

navigate through all their features and programming. While

this remote may not access every menu or guide system

of every device model, it does offer some menu and guide

functionality.

To use a device’s on-screen menu or guide system, you ﬁrst

have to put the remote in Menu or Guide Mode.

1. Make sure your devices are turned on and your TV is set

to the correct device input (use the INPUT key to toggle

through inputs when in TV Mode.)

2. Press the device key whose menu you want to access.

4. Use the VOL+/- and CH+/- keys to

navigate through the on-screen

menu system or guide. To select the

highlighted item, press the OK key.

TIP: If the remote doesn’t respond,

check to see that the ON•OFF key is

still blinking. The ON•OFF key times

out after 20 seconds. If this happens,

just press the MENU key again, and

then retry your selection.

Exiting Menu/Guide Mode

The remote automatically times out of Menu or Guide Mode

after 20 seconds of inactivity (no keys being pressed). At that

time, the remote clears the displayed menu from the TV.

If you want to exit the Menu Mode yourself, press the

corresponding device key on the remote (TV, SAT•CBL•DTC,

DVD, VCR•AUX). The ON•OFF key turns off.

Problem: The remote does not operate your device.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD, VCR•AUX).

This tells the remote which device to operate.

• Remove any obstacles between the remote and the device. Make

sure you’re aiming the remote at the device’s IR sensor.

• Make sure the batteries are fresh and are properly installed.

Replace the batteries with two new AA batteries, if necessary

(see the Battery Installation section).

Problem: The remote can’t be programmed to operate your

device.

• If you are testing the remote while programming it, you may be

too far away from the device or at a wrong angle. There must be

an unobstructed path between the remote and the IR sensor on

the device. Move closer and make sure you point the remote at

the device you’re trying to control.

• If you’re using the Direct Entry programming method to enter

the codes for your brand and the unit is still not functioning

properly, try the auto, brand, or manual search method.

• To control combo units, like TV/VCRs or TV/DVDs, you must

program the individual corresponding device keys to control

each part of the combo unit. Once programmed successfully, the

TV key controls the TV functions, and the VCR•AUX or DVD key

controls the VCR or DVD functions.

• Make sure the batteries are fresh and are properly installed.

Problem: The remote doesn’t perform commands properly.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD, VCR•AUX).

This tells the remote which device to operate.

• Make sure device is ready (for example, the DVD player has a

disc loaded).

• You may have pressed an invalid key for the mode the remote is in.

• If you’re trying to enter a channel number directly, try pressing

the OK key after entering the channel number as this is a

requirement of certain models and brands.

• There is a possibility that a programmed code may only be

able to control some of your device features (for example, only

turns a device on and off). To conﬁrm that the device key is

programmed with the correct code for maximum functionality,

test the device. Attempt to control a variety of the device’s

functions with the remote. If some of the features of your

devices don’t work, try programming the remote with a different

code in the list using the Direct Code Entry Method, until you

ﬁnd the code that allows the remote to control the majority of

your device’s functions. Different codes can provide different

levels of functionality.

Problem: The ON•OFF key does not light when you press a key.

• You may have pressed an invalid key for the mode the remote is

in.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD, VCR•AUX).

This tells the remote which device to operate.

• Make sure the batteries are fresh and are properly installed.

Replace the batteries with two new AA batteries, if necessary

(see the Battery Installation section).

Problem: The remote will not change channels on device.

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD, VCR•AUX).

This tells the remote which device to operate.

• Press the OK key after you enter a channel number.

• Remove any obstacles between the remote and the device. Make

sure to aim the remote at the IR sensor on the device.

Problem: The device’s menu does not appear on the TV screen.

• Make sure you have connected the device to your TV properly and

selected the correct input. (See your devices’ Owner’s Manuals for

proper connection procedures.)

• Make sure the remote is in the correct mode by pressing the

corresponding device key (TV, SAT•CBL•DTC, DVD, VCR•AUX).

This tells the remote which device to operate.

• Menu access isn’t supported for all brands. You may need to use

your original remote control to access menu functions for some

devices.

For more information, please visit www.rcaaccessories.com

Consumer Help Line: 1-800-420-7968

Audiovox Electronics Corporation (the “Company”) warrants to you the

original retail purchaser of this product that should it, under normal use

and conditions, be proven defective in material or workmanship during

its lifetime while you own it, such defect(s) will be repaired or replaced

(at the Company’s option) without charge for parts and repair labor. To

obtain repair or replacement within the terms of this Warranty, the product

is to be delivered with proof of warranty coverage (e.g. dated bill of sale),

speciﬁcation of defect(s), transportation prepaid, to the Company at the

address shown below.

This Warranty does not cover product purchased, serviced or used outside

the United States or Canada. This Warranty is not transferable and does

not extend to costs incurred for installation, removal or reinstallation of

the product. This Warranty does not apply if in the Company’s opinion,

the product has been damaged through alteration, improper installation,

mishandling, misuse, neglect, accident, or the simultaneous use of different

battery types (e.g. alkaline, standard or rechargeable).

THE EXTENT OF THE COMPANY’S LIABILITY UNDER THIS WARRANTY IS

LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO

EVENT, SHALL THE COMPANY’S LIABILITY EXCEED THE PURCHASE PRICE

PAID BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL

BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL

THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL

DAMAGES WHATSOEVER. No person or representative is authorized

to assume for the Company any liability other than expressed herein in

connection with the sale of this product.

Some states/provinces do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential

damage so the above limitations or exclusions may not apply to you. This

Warranty gives you specic legal rights and you may also have other rights,

which vary from state/province to state/province.

U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,

New York 11788

CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,

Unit 3, Door 16, Mississauga, Ontario L5T 3A5

Trademark(s) ® Registered

RCR412 US 04

111 Congressional Blvd., Suite 350

Carmel, IN 46032

Tour of the Remote

Advanced Functions

Troubleshooting

Limited Lifetime Warranty

DVD CoDe

SAT•CBL•DTC CoDe

TV CoDe

SAT CABLE DTV ConVErTEr

3. To access menus, press the MENU key. To access guides,

press the GUIDE key. The ON•OFF key starts blinking,

indicating you are in Menu or Guide Mode. ON•OFF key

2. Press and hold the device key you want to program. While

you’re holding down the device key, use your other hand

to press and hold the remote’s ON•OFF key at the same

time.

Note: All TV codes begin with the number 1; all VCR and DVR

codes begin with the number 2; all DVDs, the number 3; and

all satellite receivers, cable boxes and digital TV converters,

the number 5.

5. Repeat step 4 until you have retrieved all ﬁve numbers in

the code. After the fth number is retrieved, the ON•OFF

key blinks brieﬂy, then turns off.

TIP: To exit the Code Retrieval Mode at any time, press the

GO BACK key.

Note: If you press an invalid key during the Code Retrieval

process, the remote will not respond. If you do not press a

valid Code Retrieval key (TV, SAT•CBL•DTC, DVD, VCR•AUX,

INFO, GO BACK), Code Retrieval times out after 15 seconds.

The ON•OFF key blinks four times, and then turns off.

GO BACK exits remote programming; it also performs the

same functions as on your original remotes.

The and key has three functions: (1) it toggles INPUT — (dash)

through all the video sources connected to your TV; (2) when

the remote is in VCR mode, this button toggles between VCR

and the TV input; (3) when you’re entering digital channel

numbers directly, this button lets you separate the main

channel number from the sub-channel number (such as 59.1).

Backlighting

Backlight illumination helps you see the remote control keys

better in the dark. You can turn backlight illumination on or off

by pressing the backlight key ( ). Backlighting stays on as

long as keys are being pressed and turns off six seconds after

the last keypress. Once the backlight time has timed out, any

keypress will reactivate it. If the backlight illumination is on,

and you press the backlight key, the backlight turns off.

2. While holding the device key down, press and hold the

INFO key. The ON•OFF key turns off. After holding down

both keys for three seconds, the ON•OFF key turns back

on.

3. Release both keys. The ON•OFF key remains on.

4. Starting with the number 1 key, press and release each

number key on the keypad in the following order: 1-9, then

0. The number that causes the ON•OFF key to blink is the

ﬁrst number of the code. As you ﬁnd each number of the

code, write it down for future reference.

Actual model may vary

from illustration

Changing A Key’s Device Type

Each device key is associated with a type of device—the TV is

preset to search for TVs, SAT•CBL•DTC for satellite receivers,

cable boxes or digital TV converters, DVD for DVD players, and

VCR•AUX for VCRs or DVRs. To program these keys to control

a different kind of device, you have to reassign them ﬁrst.

ReassigningtheVCR•AUXKeyToControlOther

Devices

The VCR•AUX key defaults to control a VCR or DVR. If you want

the VCR•AUX key to control a different device (an additional

TV, DVD, satellite, cable box or digital TV converter, for

example), you must reassign it.

1. Press and hold the VCR•AUX key. The ON•OFF key turns on.

2. While holding down the VCR•AUX key, press and release the

number key on the keypad for the device you wish to control

(see the chart below). The ON•OFF key turns off.

3. Release the VCR•AUX key. The ON•OFF key blinks four

times and then turns off. The VCR•AUX key is now set to

control the device type you selected.

4. Follow the directions in the auto, brand, direct entry, or

manual code search to program the VCR•AUX key.

VCR•AUX KEY CONTROLS:

Additional TV press 1

VCR or DVR press 2

Additional DVD press 3

Additional satellite, cable box or

digital TV converter

press 5

VCR•AUX CoDe

DVr/VCr DVD TV SAT•CBL•DTC

Manual del Propietario del

Control Remoto Universal

RCR412BN / RCR412SN / RCR412SIN

Owner’sManual(Englishonback)

¡GUARDE ESTE MANUAL Y LAS LISTAS DE CÓDIGOS!

En ocasiones los controles remotos pierden su programación

cuando se cambian las baterías. Asegúrese de mantener el

manual y las listas de códigos en un lugar seguro de manera

que pueda volver a programar el control remoto de ser

necesario.

Consejo: Este control remoto p3-ya está programado para la

mayoría de televisores, VCR, lectores de DVD y receptores de

satélite RCA. Sencillamente oprima la tecla correspondiente—

DVD para un Lector de DVD, TV para un televisor, SAT•CBL•DTC

para un receptor de satélite, VCR•AUX para un VCR.

Cómo Probar el Código para Obtener Máxima Funcionalidad

1. Pruebe una variedad de funciones del dispositivo con el

control remoto. Si no puede utilizar alguna de las funciones del

dispositivo, vaya al próximo paso e intente un código diferente.

2. Repita la Búsqueda Automática de Códigos desde el comienzo.

Cuando su dispositivo se apague, no detenga la búsqueda. En

vez, con la unidad apagada, continúe oprimiendo la tecla PLAY

cada 5 segundos hasta que la unidad se vuelva a encender.

3. Cuando se vuelva a encender la unidad, oprima la tecla

REVERSE en el control remoto cada 2 segundos hasta que el

dispositivo se vuelva a apagar. Cuando el dispositivo se vuelva

a apagar, oprima la tecla STOP.

4. Nuevamente, pruebe la funcionalidad de la tecla intentando

controlar una variedad de funciones del dispositivo. Si el código

que se p3-ha almacenado controla la mayoría de las funciones del

dispositivo, entonces habrá concluido la programación. Si el código

guardado no brinda una máxima funcionalidad, intente otro código.

1. Encienda manualmente el

dispositivo que desea manejar.

2. Oprima y sostenga la tecla de dispositivo que desea programar.

A la vez que sostiene la tecla de dispositivo, utilice la otra mano

para oprimir y sostener simultáneamente la tecla ON•OFF del

control remoto.

3. Espere hasta que la tecla ON•OFF se ilumine y permanezca

iluminada. Luego, suelte ambas teclas.

4. Mantenga el control remoto

apuntado directamente al panel

frontal del dispositivo que desea

manejar. Oprima la tecla PLAY del

control remoto y espere 5 segundos.

El control remoto está probando

un grupo de 10 códigos para el

dispositivo.

¿Se apagó el dispositivo?

SÍ: Vaya al Paso 5.

NO: Oprima PLAY nuevamente. El control remoto prueba el

próximo grupo de 10 códigos.

Continúe oprimiendo PLAY cada 5 segundos hasta que el

dispositivo se apague.

5. Cuando el dispositivo se apague,

oprima la tecla REVERSE del control

remoto y espere por lo menos 2

segundos. El control remoto prueba el

último código del grupo anterior de 10

códigos.

¿Se encendió el dispositivo?

SÍ: Oprima la tecla STOP. ¡Listo! La

tecla de dispositivo está programada.

NO: Oprima REVERSE nuevamente. El control remoto prueba el

próximo código en el grupo de códigos.

Continúe oprimiendo REVERSE cada 2 segundos hasta que el

dispositivo se encienda. Cuando se encienda, oprima STOP.

Aviso: Si oprime accidentalmente la tecla REVERSE luego de

que el dispositivo se encienda, oprima la tecla FORWARD. Luego,

espere dos segundos para ver si su dispositivo se vuelve a apagar.

NOTAS

A través de la programación de cada tecla, asegúrese de

mantener el control remoto apuntado directamente al sensor

infrarrojo del dispositivo que está actualmente programando

con el control remoto.

Pruebe el control remoto con el dispositivo para asegurarse que

la tecla de dispositivo esté programada con el código correcto

y garantizar así su máxima funcionalidad. Si no puede utilizar

alguna de las funciones, intente con otro código. Para obtener

mayor información, consulte la sección “Cómo Probar el Código

para Obtener Máxima Funcionalidad” a continuación.

Durante la Búsqueda Automática de Códigos, el control remoto

ignora la opresión de teclas que no son parte de la búsqueda.

La búsqueda se detendrá luego de dos minutos (la tecla ON•OFF

parpadea cuatro veces y se apaga, y se retiene el último código

programado bajo la tecla de dispositivo).

La tecla ON•OFF parpadea cuatro veces y se apaga cuando

el control remoto p3-ha recorrido todos los códigos. El control

remoto sale del método de Búsqueda Automática de Códigos.

Si su dispositivo aún no se p3-ha apagado, intente un método de

búsqueda diferente.

Cómo Probar el Código para Obtener Máxima Funcionalidad

1. Pruebe una variedad de funciones del dispositivo con el control

remoto. Si no puede utilizar alguna de las funciones de sus

dispositivos, vaya al próximo paso e intente un código diferente.

2. Repita la Búsqueda de Códigos por Marca desde el comienzo.

Cuando el dispositivo se apague por primera vez, no oprima la

tecla STOP, con la cual quedaría guardado . En el mismo código

vez, con la unidad apagada, continúe oprimiendo la tecla ON•OFF

repetidamente hasta que la unidad se vuelva a encender.

3. Si se vuelve a encender la unidad, habrá encontrado otro código

que puede manejar ese dispositivo. Oprima STOP.

4. Pruebe la funcionalidad de la tecla nuevamente intentando

una variedad de funciones. Si el código controla la mayoría

de las funciones del dispositivo, entonces habrá concluido la

programación. Si el código guardado no brinda una máxima

funcionalidad, intente otro código.

Búsqueda de Códigos por Marca

La Búsqueda de Códigos por Marca recorre sólo los códigos

de una de las marcas seleccionadas que aparecen en la lista de

códigos suministrada. Si la marca del dispositivo aparece en la lista,

posiblemente la búsqueda se llevará a cabo de manera fácil y rápida.

CONSEJOS: Cada tecla de dispositivo está asociada a un

tipo de dispositivo—TV está congurada para buscar TV,

SAT•CBL•DTC para receptores de satélite, aparatos de cable

o convertidores de TV digital, DVD para lectores de DVD, y

VCR•AUX para unidades VCR o DVR. Para programar una tecla

de dispositivo para un tipo de dispositivo diferente, consulte la

sección Cómo Cambiar el Tipo de Dispositivo de Una Tecla.

La tecla ON•OFF sirve de luz indicadora durante la

programación, ofreciéndole retroalimentación en cada etapa del

proceso.

Para salir en cualquier momento de la Búsqueda de Códigos por

Marca sin guardar un código nuevo, oprima la tecla GO BACK.

1. Encienda manualmente el

dispositivo que desea manejar.

3. Oprima y sostenga la tecla de dispositivo que desea programar.

A la vez que sostiene la tecla de dispositivo, utilice la otra mano

para oprimir y sostener simultáneamente la tecla ON•OFF del

control remoto.

4. Espere hasta que la tecla ON•OFF se ilumine y permanezca

iluminada. Luego, suelte ambas teclas.

6. Mantenga el control remoto apuntado

directamente al panel frontal del

dispositivo que desea manejar. Oprima

la tecla ON•OFF y espere 2 segundos.

El control remoto está probando un

código para la marca del dispositivo.

¿Se apagó el dispositivo?

SÍ: Oprima la tecla STOP para guardar el código. ¡Listo! La tecla

de dispositivo está programada.

NO: Oprima ON•OFF nuevamente. El control remoto prueba el

próximo código para su marca.

Continúe oprimiendo ON•OFF cada 2 segundos hasta que el

dispositivo se encienda. Cuando se encienda, oprima STOP.

2. Encuentre la marca del dispositivo

en la sección de Códigos por Marca

de la lista de códigos suministrada.

Marque con un círculo el número de

la marca y mantenga la lista a mano.

Co d e L i ts

Li s ta de Có di g os

2 3

5 6

789

VCR

2 3

5 6

789

DVD

SA /CABLE

2 3

5 6

789

2 3

5 6

789

5. Fíjese en el número que marcó para

el número de código de la marca del

dispositivo. Oprima dicho número en el

teclado del control remoto.

NOTAS

A través de la programación de cada tecla, asegúrese de

mantener el control remoto apuntado directamente al sensor

infrarrojo del dispositivo que está actualmente programando con

el control remoto.

Pruebe el control remoto con el dispositivo para asegurarse que

la tecla de dispositivo esté programada con el código correcto

y garantizar así su máxima funcionalidad. Si no puede utilizar

alguna de las funciones, intente con otro código. Para obtener

mayor información, consulte la sección “Cómo Probar el Código

para Obtener Máxima Funcionalidad” a continuación.

Durante la Búsqueda de Códigos por Marca, el control remoto

ignora la opresión de teclas que no son parte de la búsqueda.

La búsqueda se detendrá luego de dos minutos (la tecla ON•OFF

parpadea cuatro veces y se apaga, y se retiene el último código

programado bajo la tecla de dispositivo).

La tecla ON•OFF parpadea cuatro veces y se apaga cuando

el control remoto p3-ha recorrido todos los códigos. El control

remoto sale del método de Búsqueda de Códigos por Marca.

Si su dispositivo aún no se p3-ha apagado, intente un método de

búsqueda diferente.

Entrada Directa de Códigos

La Entrada Directa de Códigos le permite ingresar un código de la

lista de códigos suministrada para la marca de su dispositivo. No

es tan fácil como los otros métodos, pero es posiblemente el más

rápido.

1. Encienda manualmente el dispositivo

que desea manejar.

3. Oprima y sostenga la tecla de dispositivo que desea programar

(la tecla ON•OFF se ilumina).

Mientras oprime la tecla de dispositivo, ingrese con la otra mano

el primer código de cinco dígitos para la marca de la lista de

códigos (la tecla ON•OFF se apaga luego del primer dígito).

2. Encuentre la Lista de Códigos

suministrada con el control remoto.

Encuentre la sección para el tipo de

dispositivo que desea programar,

y localice la marca en esa sección.

Marque con un círculo los códigos

para la marca y manténgalos a mano.

Co d e L is ts

Li s ta de Có di g os

2 3

5 6

789

T V

VCR

2 3

5 6

789

DVD

SA CAB LE

2 3

5 6

789

2 3

5 6

789

NOTAS

Recuerde ingresar el código para referencia futura en el

recuadro provisto en la sección Recuperación de Códigos de

este manual.

Si la marca de su dispositivo no aparece en la lista de códigos,

utilice uno de los métodos de Búsqueda de Códigos para

programar el control remoto. (Consulte los métodos de

Búsqueda Automática y Manual de Códigos)

Si suelta la tecla de dispositivo en cualquier momento durante

el proceso de Entrada Directa de Códigos, la tecla ON•OFF

parpadea cuatro veces, y se sale del proceso. Se retendrá el

último código programado bajo la tecla de dispositivo.

Pruebe el control remoto con el dispositivo para asegurarse que

la tecla de dispositivo esté programada con el código correcto

y garantizar así su máxima funcionalidad. Si no puede utilizar

alguna de las funciones, intente con otro código de la lista.

4. Cuando haya ingresado el código de cinco dígitos, continúe

oprimiendo la tecla de dispositivo y observe la tecla ON•OFF.

¿SeiluminólateclaON•OFF?

SÍ: ¡Listo! La tecla de dispositivo está programada.

No, parpadeó cuatro veces : y se apagó Ha ingresado un

número de código que no se encuentra en las listas de códigos

u omitió un paso en el procedimiento de entrada de códigos.

Intente el paso 3 nuevamente.

Búsqueda Manual de Códigos

La Búsqueda Manual de Códigos le permite recorrer uno por uno

todos los códigos del dispositivo que desea manejar. Cuando

encuentre el que maneja su dispositivo, puede detener la búsqueda y

guardar el código.

CONSEJOS: La tecla ON•OFF sirve de luz indicadora durante la

programación, ofreciéndole retroalimentación en cada etapa del

proceso.

Cada tecla de dispositivo está asociada a un tipo de dispositivo—

TV está congurada para buscar TV, SAT•CBL•DTC para

receptores de satélite, aparatos de cable o convertidores de TV

digital, DVD para lectores de DVD, y VCR•AUX para unidades VCR

o DVR. Para programar una tecla de dispositivo para un tipo de

dispositivo diferente, consulte la sección Cómo Cambiar el Tipo

de Dispositivo de Una Tecla.

El método de Búsqueda Manual de Códigos podría tomar más

tiempo porque el control remoto busca a través de todos los

códigos en su memoria uno por uno. Si su marca aparece en las

Listas de Códigos por Marca o Listas de Códigos, intente primero

la Búsqueda de Códigos por Marca o el método de Entrada

Directa de Códigos.

Para salir en cualquier momento de la Búsqueda Manual de

Códigos sin guardar un código nuevo, oprima la tecla GO BACK.

CONSEJO: Cada tecla de dispositivo está asociada a un tipo de

dispositivo—TV está congurada para buscar TV, SAT•CBL•DTC

para receptores de satélite, aparatos de cable o convertidores de TV

digital, DVD para lectores de DVD, y VCR•AUX para unidades VCR

o DVR. Para programar una tecla de dispositivo para un tipo de

dispositivo diferente, consulte la sección Cómo Cambiar el Tipo

de Dispositivo de Una Tecla.

La tecla ON•OFF sirve de luz indicadora durante la programación,

ofreciéndole retroalimentación en cada etapa del proceso.

Ahorro de Batería

Su control remoto universal ahorra la potencia de las baterías al

apagar automáticamente cualquier tecla que se oprima por más

de 60 segundos. Esta acción prolonga la vida útil de las baterías

en caso de que el control remoto quede pillado en un lugar donde

las teclas permanezcan oprimidas, tal como entre los cojines de un

sofá.

El control remoto necesita dos baterías alcalinas AA (las baterías

pueden estar incluidas o no, dependiendo de modelo).

Para instalar las baterías:

1. Retire la tapa del compartimiento de

las baterías.

2. Inserte las baterías, cerciorándose

de que las polaridades (+) y (–)

correspondan con el diagrama que

aparece en el compartimiento de las

baterías.

3. Vuelva a colocar la tapa del

compartimiento de las baterías en su

posición.

Precauciones sobre las Baterías:

• No combine baterías nuevas y viejas.

• No combine diferentes tipos de baterías: alcalinas, estándar

(carbón-zinc) o recargables (níquel-cadmio).

• Siempre remueva de inmediato baterías viejas, débiles o

desgastadas, y recíclelas o deséchelas según lo disponen las

normas locales y nacionales.

Paso 1: Instale las baterías

Para utilizar este control remoto universal con su sistema de

entretenimiento en el hogar, necesitará primero programarlo

para manejar sus dispositivos. Para programar el control remoto

universal para manejar sus dispositivos, utilice uno de los cuatro

métodos a continuación.

• La Búsqueda Automática de Códigos recorre

automáticamente todos los códigos del dispositivo que desea

manejar. Éste es el método más fácil, pero a veces toma más

tiempo que algunos de los demás métodos de programación.

• La busca a través de los Búsqueda de Códigos por Marca

códigos según la marca de dispositivos seleccionada. No es tan

fácil como la búsqueda de códigos automática, pero muchas

veces puede ser más rápida.

• La Entrada Directa de Códigos le permite ingresar un

código de la lista de códigos suministrada para la marca de su

dispositivo. No es tan fácil como los otros métodos, pero es

posiblemente el más rápido.

• La Búsqueda Manual de Códigos le permite recorrer

manualmente todos los códigos del dispositivo que desea

manejar.

Búsqueda Automática de Códigos

La Búsqueda Automática de Códigos recorre automáticamente

todos los códigos del dispositivo que desea manejar. Cuando

encuentre el que maneja su dispositivo, puede detener la búsqueda

y guardar el código.

Paso 2: Programe el control remoto

CONSEJO: Cada tecla de dispositivo está asociada a un tipo de

dispositivo—TV está congurada para buscar TV, SAT•CBL•DTC

para receptores de satélite, aparatos de cable o convertidores de TV

digital, DVD para lectores de DVD, y VCR•AUX para unidades VCR

o DVR. Para programar una tecla de dispositivo para un tipo de

dispositivo diferente, consulte la sección Cómo Cambiar el Tipo de

Dispositivo de Una Tecla.

Para salir en cualquier momento de la Búsqueda Automática de

Códigos sin guardar un código nuevo, oprima la tecla GO BACK.

Especificaciones del producto

Marca:	Audiovox
Categoría:	Mando a distancia
Modelo:	RCR412BN
Color del producto:	Zwart
Peso del embalaje:	4550 g
Ancho del embalaje:	635 mm
Empaquetadura en profundidad:	105 mm
Altura del embalaje:	410 mm
Sensor de luz ambiental:	Ja
Tipo de embalaje:	Doos
Control remoto:	XRT134
Diagonal de la pantalla:	24 "
Resolución:	1280 x 720 Pixels
Relación de aspecto original:	16:9
Ángulo de visión, horizontal:	178 °
Ángulo de visión, vertical:	178 °
Forma de pantalla:	Flat
Brillo:	- cd/m²
Número de puertos USB 2.0:	1
Número de puertos HDMI:	2
Entrada de vídeo compuesto:	1
Vídeo de componentes (YPbPr/YCbCr):	1
Altavoces incorporados:	Ja
Energía promedio:	2 W
Consumo de energía (en espera):	0.5 W
Número soportado de baterías/baterías:	2
Número de hablantes:	2
Certificación:	ENERGY STAR® 7.0
tipo HD:	HD
3D:	Nee
Tecnología de visualización:	LED
Tiempo de respuesta:	- ms
Montaje VESA:	Ja
Interfaz de montaje en panel:	100 x 100 mm
Certificados de sostenibilidad:	ENERGY STAR
Profundidad (sin base):	52 mm
Altura (sin base):	355 mm
Ancho (sin base):	535 mm
Peso (sin base):	2750 g
Ancho del dispositivo (con soporte):	535 mm
Dispositivo de profundidad (con soporte):	105 mm
Altura del dispositivo (con soporte):	360 mm
Peso (con soporte):	3200 g
Canal de retorno de audio (ARC):	Ja
Tipo de retroiluminación LED:	Edge-Lit LED
Mando a distancia incluido:	Ja
Wifi.:	Nee
Consumo de energía (típico):	18.94 W
Baterias-incluidas:	Ja
Tipo de Batería:	AAA