Barco ImagePRO-4K Manual de Usario
Lee a continuación 📖 el manual en español para Barco ImagePRO-4K (2 páginas) en la categoría Enrutador. Esta guía fue útil para 14 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Note: The ImagePRO 4K automatically acquires and congures inputs.–
Setting up an LED display
Note: To enter the Setup menu press the Adjust Knob.
ImagePRO 4K Video Processor: Rear-Panel Setup–
Genlock
BNC Input
Quick install and setup
ImagePRO 4K Video Processor–
Quick Start Guide - Setup
P/N 26-1602004-00, Rev 01
Connect inputs Connect all input sources to the —
ImagePRO 4K.–
1Connect power Ensure that power is properly connected —
to the ImagePRO 4K.–
2
Getting started
Barco Technical Support:
USA:
EMEA:
China:
APAC:
Support:
+1 (866) 374-7878
+32 (56) 36 8019
40088 22726
+603-78803362
www.barco.com/en/support
3
4
5
Connect outputs Connect the output(s) on the —
ImagePRO 4K to your projector(s) or other target devices.–
Turn on power Turn on power to the ImagePRO 4K, — –
your projector(s), and to all peripheral equipment.
Factory reset If you are using the ImagePRO 4K for the — –
rst time, or if you are using an ImagePRO 4K that has just –
returned from an event, perform a full factory reset to restore
default system congurations.
Press the Adjust Knob to enter the Setup menu, then select
Reset / Factory Reset / Soft Reset on the display screen.
keeps the user settings.
Adjust output format Setup / Output / AUX Go to —
Adjustment and update the output format.
6Native Rate O—n the front panel, press the Adjust Knob to
enter the Setup menu, then select and Setup / System menu
select the desired Native Rate.
8
Setting up outputs
9
10
Test output Turn on a test pattern, verify that you have an —
image, and make any necessary adjustments. When
complete, turn o the test pattern.
11 Set and adjust inputs / source Select inputs / sources and make any —
necessary adjustments to color balance, timings, and so on.
Setting up inputs / source
12
Save input / source configurations After adjusting an input / source, —
save the input /source configuration.
Repeat steps 11 and 12 for each input / source.
13 Adjust and save system settings Adjust system parameters such as —
Ethernet settings and HDCP parameters.
For complete details on all installation and operations procedures, please
refer to the (R5906167).ImagePRO 4– K User’s Guide
ImagePRO 4– K User’s Guide
AC
Connect to AC
power source
Ethernet
Connect to Event
Master Toolset or
External Controller
Genlock
Generated
Reference Output
DP 1.2
Input
HDMI 2.0
Input
12G SDI
Input
12G SDI
Input
12G SDI
Input
12G SDI
Input
DP 1.2
Output
HDMI 2.0
Output
12G SDI
Output
12G SDI
Output
12G SDI
Output
12G SDI
Output
Position and adjust the image Use the LED Setup Menu to —
position the image on the LED wall or other display device,
scale the image, adjust and settings, and save your Pan Zoom
view.
Save All Save All Save All Select —. is the last menu item on the Setup
page. writes system settings to non-volatile memory.Save All
14
System settings
Assign primary output If the primary output is DP, —
proceed to the next step.
If your primary output is HDMI/SDI, go to Setup / Output /
AUX Adjustment and update the primary output.
7
Adjust Knob and Display screen
Adjust Knob
Navigate through
menus; push to
activate menus
ImagePRO 4K Video Processor: Front-Panel Setup–
USB Port
Connect a flash drive to
back up and restore
configurations and to
upload firmware
Display Screen
Displays menus,
messages, and
live video
Menu/Monitor
Toggles between Menu
and Monitor Mode
LED
Setup
Menus
Source
Buttons
1 8–
FRZ
Freezes an
image
ImagePRO 4K Video Processor–
Quick Start Guide - Setup
P/N 26-1602004-00, Rev 01
· 1RU rack-mount chassis
· Resolution up to 4096 x 2160 @ 60
· 4:4:4, 10-bit color (DP 1.2)
· Up to 6 inputs, each independently scaled to a dierent output
resolution
· DisplayPort 1.2 I/O
· HDMI 2.0/HDCP 2.2 I/O
· 1.5G/3G/6G/12G SDI I/O
· Up to 2x 4K60 inputs and outputs simultaneously
· Dedicated Genlock BNC connector
· Ethernet connection on the rear panel
· A USB port on the front panel
· Programmable input EDID
· Sync output
· Custom output formats
· Output rotation (90/180/270 degrees)
· Seamless cut transition or fade through matte color or a logo
Features overview
Barco Technical Support:
USA:
EMEA:
China:
APAC:
Support:
+1 (866) 374-7878
+32 (56) 36 8019
40088 22726
+603-78803362
www.barco.com/en/support
Remote control options
Overview of key operations menus
Input Menu Set input format; adjust brightness and contrast; adjust aspect ratio; set color –
balance; size the image; save and manage input congurations; manage Input HDCP
settings.
Output (AUX) Menu Set output format; detect output EDID; create an Area of Interest; –
adjust timing and colorspace; set eects such as sharpness, strobe mode, color inversion;
manage Output HDCP settings.
Still Menu Capture, rename, and delete stills. Set selected still as logo.–
Preset Menu Store and recall presets.–
Transition Menu Set transition timing and eects.–
Button Mapping Menu Map source and output buttons. SRC 1 SRC 6 default to the – –
inputs of the Tri-Combo input card; SRC 7 ; and SRC 8 .defaults to “Matte” defaults to “Logo ”
OUT 1 OUT 6 default to OUT 1 as Aux Channel A, OUT 2 as Aux Channel B; OUT 3 6 – –
are not mapped.
System Menu Set system mode and parameters including Operation Mode and Native –
Rate; manage Genlock settings; USB Backup/Restore of congurations; set Ethernet
options; lock front panel; run diagnostics.
Custom Format Menu Create, save, delete custom input and output formats.–
LED Setup Menu Quickly set up output area of interest, input scaling, and save the –
settings.
Factory Reset Restore factory default settings. Optionally, keep IP address and EDID –
settings.
Firmware Upgrade Update ImagePRO-4K rmware from a ash drive.–
TAKE
Executes transitions
ESC
Exits a menu, goes
back one level,
deactivates a selection
TEST
PATT
Test
Patterns
Output
Buttons
1 6–
· Web Interface Enables access from a computer, –
smartphone, tablet, or other web-enabled device.
· Barco Event Master Controllers Event Master Toolset –
screen management software for PC or MAC; Event Master
Controllers.
· Dimly lit Source is mapped but not active.–
· Not lit Button is not mapped.–
· Brightly lit Button is selected.–
Press the Adjust Knob to enter menus on the display screen and to
make selections.
Turn the Adjust Knob to scroll up or down through the menus on the
display screen.
Source-button states
· Lit Button is mapped, selected, or frozen.–
Output-button states
Green —Button is mapped to an Aux.
Amber —Aux is selected to view in the front-panel monitor.
Blue —Aux is frozen.
· Not lit Button is not mapped.–
Green —Signal is active and assigned to PVW.
Yellow —Input source, still, logo, or matte color is present.
Amber —Signal is active on the PGM outputs.
Red —Loss of sync (LOS).
Blue —Source is frozen.
Cyan —A cue is mapped to the button (future).
Magenta —A user key is mapped to the button (future).
White —A preset is mapped to the button.
Especificaciones del producto
| Marca: | Barco |
| Categoría: | Enrutador |
| Modelo: | ImagePRO-4K |
¿Necesitas ayuda?
Si necesitas ayuda con Barco ImagePRO-4K haz una pregunta a continuación y otros usuarios te responderán
Enrutador Barco Manuales
11 Agosto 2024
Enrutador Manuales
- Enrutador Samsung
- Enrutador Huawei
- Enrutador HP
- Enrutador DeWalt
- Enrutador Motorola
- Enrutador Nokia
- Enrutador Siemens
- Enrutador Topcom
- Enrutador Alcatel
- Enrutador Allnet
- Enrutador Alfa
- Enrutador Allied Telesis
- Enrutador Apple
- Enrutador Airlive
- Enrutador Edimax
- Enrutador Strong
- Enrutador Hikvision
- Enrutador Arris
- Enrutador BenQ
- Enrutador Makita
- Enrutador Hitachi
- Enrutador Thomson
- Enrutador Gembird
- Enrutador Black And Decker
- Enrutador Asus
- Enrutador Eminent
- Enrutador Renkforce
- Enrutador Vivanco
- Enrutador Sitecom
- Enrutador Metabo
- Enrutador TP Link
- Enrutador Manhattan
- Enrutador Black Box
- Enrutador Trust
- Enrutador Hikoki
- Enrutador Roland
- Enrutador ZTE
- Enrutador Nilox
- Enrutador Hama
- Enrutador AVM
- Enrutador TCL
- Enrutador Gigabyte
- Enrutador Techly
- Enrutador Totolink
- Enrutador Cisco
- Enrutador Engenius
- Enrutador KPN
- Enrutador Netis
- Enrutador Digitus
- Enrutador Draytek
- Enrutador Belkin
- Enrutador Devolo
- Enrutador Linksys
- Enrutador Buffalo
- Enrutador Powerplus
- Enrutador Porter-Cable
- Enrutador Dahua Technology
- Enrutador Netgear
- Enrutador Nest
- Enrutador LevelOne
- Enrutador BT
- Enrutador Vodafone
- Enrutador ICIDU
- Enrutador Mercusys
- Enrutador Milan
- Enrutador Planet
- Enrutador ZyXEL
- Enrutador Western Digital
- Enrutador Clas Ohlson
- Enrutador Konig
- Enrutador Sweex
- Enrutador MSI
- Enrutador Foscam
- Enrutador Zebra
- Enrutador D-Link
- Enrutador Aruba
- Enrutador Tenda
- Enrutador Phicomm
- Enrutador Teltonika
- Enrutador Ubiquiti Networks
- Enrutador Zoom
- Enrutador Kasda
- Enrutador Thrustmaster
- Enrutador Jung
- Enrutador Technicolor
- Enrutador Synology
- Enrutador Trendnet
- Enrutador Mikrotik
- Enrutador ATen
- Enrutador Digi
- Enrutador Verizon
- Enrutador T-Mobile
- Enrutador Conceptronic
- Enrutador RGBlink
- Enrutador Gefen
- Enrutador RAVPower
- Enrutador Hawking Technologies
- Enrutador Kopul
- Enrutador Nexxt
- Enrutador Beafon
- Enrutador Zolid
- Enrutador Sagemcom
- Enrutador SPL
- Enrutador Logilink
- Enrutador Moxa
- Enrutador Smart-AVI
- Enrutador StarTech.com
- Enrutador Holzmann
- Enrutador SIIG
- Enrutador Eero
- Enrutador Advantech
- Enrutador IOGEAR
- Enrutador Xantech
- Enrutador KanexPro
- Enrutador Intelix
- Enrutador Blustream
- Enrutador Intellinet
- Enrutador Lancom
- Enrutador Ubee
- Enrutador SMC
- Enrutador Tele 2
- Enrutador Kogan
- Enrutador Ocean Matrix
- Enrutador CradlePoint
- Enrutador Sixnet
- Enrutador Kramer
- Enrutador 7inova
- Enrutador Media-tech
- Enrutador AVPro Edge
- Enrutador Cudy
- Enrutador Lindy
- Enrutador F-Secure
- Enrutador Rosewill
- Enrutador Digicom
- Enrutador Sabrent
- Enrutador On Networks
- Enrutador Atlona
- Enrutador AVMATRIX
- Enrutador PENTAGRAM
- Enrutador Leoxsys
- Enrutador Readynet
- Enrutador OneAccess
- Enrutador Accelerated
- Enrutador Nexaira
- Enrutador FSR
- Enrutador Hamlet
- Enrutador Approx
- Enrutador T-com
- Enrutador Alfatron
- Enrutador Amped Wireless
- Enrutador Key Digital
- Enrutador Cambium Networks
- Enrutador 3Com
- Enrutador I-Tec
- Enrutador Avenview
- Enrutador BZBGear
- Enrutador WyreStorm
- Enrutador Ruckus Wireless
- Enrutador Dovado
- Enrutador Mach Power
- Enrutador MuxLab
- Enrutador EXSYS
- Enrutador NetComm
- Enrutador Juniper
- Enrutador Comtrend
- Enrutador Premiertek
- Enrutador GL.iNet
- Enrutador A-NeuVideo
- Enrutador Shinybow
- Enrutador Edgewater
- Enrutador Atlantis Land
- Enrutador Lantronix
- Enrutador Lumantek
- Enrutador Keenetic
- Enrutador Starlink
- Enrutador Keewifi
- Enrutador Milesight
- Enrutador PulseAudio
- Enrutador United Telecom
- Enrutador Predator
- Enrutador Comprehensive
- Enrutador Digitalinx
- Enrutador Luxul
- Enrutador Silentwind
- Enrutador Keezel
- Enrutador Wisetiger
Últimos Enrutador Manuales
27 Octubre 2024
27 Octubre 2024
27 Octubre 2024
26 Octubre 2024
24 Octubre 2024
20 Octubre 2024
19 Octubre 2024
19 Octubre 2024
18 Octubre 2024
18 Octubre 2024