Be Quiet! Dark Rock Pro TR4 Manual de Usario

Be Quiet! Enfriador de portátiles Dark Rock Pro TR4

Lee a continuación 📖 el manual en español para Be Quiet! Dark Rock Pro TR4 (2 páginas) en la categoría Enfriador de portátiles. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Introduction: Thank you for deciding to purchase a be quiet!

product. The following instructions will guide you through the

installation process. If you do encounter installation problems,

please don't hesitate to contact our customer services by

mailing service@bequiet.com. Please note that be quiet!

cannot accept liability for damage caused by compatibility

problems.

Warranty:

• 3-year manufacturer guarantee for consumers (original

purchase from authorized be quiet! dealers only)

• Guarantee work can only be processed with a copy

included of the purchase receipt from an authorized

be quiet! dealer

• Manipulation and structural changes of any kind, including

any damage caused by external mechanical force, will

lead to a complete voiding of the guarantee

• Our General Warranty Conditions apply, which can be

viewed on bequiet.com

Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde

Germany

For further information contact us via e-mail:

service@bequiet.com

SCOPE OF DELIVERY

We recommend removal of the cooler prior to transportation.

06/2018

Part name Quantity

be quiet! Dark Rock Pro TR4

cooler 1

135mm fan 1

120mm fan 1

Long TR4 mounting bracket 1

Short TR4 mounting bracket 1

Cooler mounting bridge 1

Part name Quantity

TR4 spacer nuts 4

TR4 screws 4

Cross-tip screwdriver 1

Thermal paste 1

Fan clips 6

Y cable 1

Position the Cooler mounting bridge (6) centrally on the cooler

(1). Next place the cooler unit over the CPU. Loosen both

heatpipe caps that are found in the middle of the topside of the

cooler.

Tighten the screws of the cooler mounting bridge alternately.

You can use the cross-tip screwdriver (9) for this. Subsequently

retighten both heatpipe caps on the topside of the cooler.

Fasten the 120mm fan (3) using fan clips (11) onto the front

side of the cooler. Slide the 135mm fan (2) between the two

heatsinks and fasten this with fan clips (11). Connect both fans

using the Y cable (12). Connect this to the CPU fan connector

on the motherboard.

When dismantling the fans, push the notches of the fan clips

(11) away from the fan.

General

We recommend preparatory mounting of the

cooler outside the PC case for subsequent

installation.

Assembly of the cooler mounting frame

Place the TR4 spacer nuts (7) onto the socket bolts protruding

through the front side and afﬁ x the long TR4 mounting bracket

(4) with the TR4 screws (8). Next assemble the opposite side

with the short TR4 mounting bracket (5) as you did before.

Mounting the CPU cooler:

First remove the protective foil from the underside of the

cooler. Spread the thermal paste (10) on the surface of the

CPU. The amount supplied is sufﬁ cient for one or two

applications.

Caution: The thermal paste supplied is not suitable for human

consumption. If swallowed, drink lots of water and urgently

seek medical attention. Keep it out of the reach of children.

Avoid contact with skin and eyes.

AMD TR4

Installation video

Limited Warranty

As per the terms and conditions of this limited warranty as given

below, be quiet! warrants its new products to be free of defects

resulting from faulty materials and faulty manufacturing for the length

of the warranty period.

I. APPLICABILITY

This non-transferable warranty is applicable to newly purchased,

previously unopened be quiet! products and is enforceable by only

the original consumer purchaser. Proof of purchase is required for

warranty service, so should be retained. be quiet! does not provide

warranty registration services.

II. WARRANTY PERIOD

For eligible products, parts and labor are warranted for the appli-

cable warranty period from the date of purchase. The applicable

warranty period varies by product model, and is identiﬁ ed in your

user documentation, on the product package, or as listed below.

Should any of these warranty periods diﬀ er, the longest speciﬁ ed

warranty period will apply. Replaced products will be warranted

for the remainder of the original warranty period or thirty days,

whichever is longer.

III. EXCLUSIONS

The following are not covered by the warranty:

1. Normal wear and tear.

2. Any product which has been modiﬁ ed without permission from

be quiet!, or on which the serial number or warranty sticker has been

defaced, modiﬁ ed, or removed.

3. Damage, deterioration or malfunction resulting from:

Accident, abuse, misuse or improper use, neglect, connection to

an improper voltage source, unauthorized product modiﬁ cation, or

failure to follow instructions included with the product.

Fire, water, lightning, or other acts of nature.

Repair or attempted repair by anyone not authorized by be quiet!.

Shipping or transport damage (claims must be made with the carrier).

Any other cause which does not relate to a defect in materials or

manufacturing workmanship.

4. Cartons, cases, batteries, cabinets, tapes, accessories or other

consumables used with this product.

5. be quiet!, Inc. does not warrant that this product will meet your

requirements. It is your responsibility to determine the suitability of

this product for your purpose.

6. Removal or installation charges.

7. Shipping charges.

8. Any incidental charges.

IV. EXCLUSION OF DAMAGES

be quiet!‘s sole obligation and liability under this warranty is limited

to the repair or replacement of a defective product at its option.

be quiet! shall not, in any event, be liable for any special, incidental,

indirect, or consequential damages whatsoever, including but not

limited to loss of proﬁ ts, revenue, or data (whether direct or indirect),

damages resulting from interruption of service and loss of business,

or for liability in tort relating to this product or resulting from its use

or possession, even if be quiet! has been advised previously of the

possibility of such damages.

V. LIMITATIONS OF IMPLIED WARRANTIES

There are no other warranties, expressed or implied, including but not

limited to those of merchantability or ﬁ tness for a particular purpose.

The duration of implied warranties is limited to the warranty length

speciﬁ ed in Paragraph II.50

VI. LOCAL LAW AND YOUR WARRANTY

This warranty gives you speciﬁ c legal rights. You may also have other

rights granted under local law. These rights may vary.

VII. NO OTHER WARRANTY

No be quiet! employee, dealer, or other agent is authorized to make

any modiﬁ cation, extension, or addition to this warranty.

VIII. TO OBTAIN TECHNICAL SUPPORT OR WARRANTY SERVICE

Please see your product owner’s manual or visit the service section

at www.bequiet.com for details and contact information. You will

need to provide proof of purchase for warranty service.

bequiet.com

DARK ROCK PRO TR4

LIEFERUMFANG

Bezeichnung Anzahl

be quiet! Dark Rock Pro TR4

CPU-Kühler 1

135mm Lüfter 1

120mm Lüfter 1

Lange TR4 Montagebrücke 1

Kurze TR4 Montagebrücke 1

Kühler-Montagebrücke 1

Bezeichnung Anzahl

TR4 Abstandsbolzen 4

TR4 Schrauben 4

Kreuzschraubenzieher 1

Wärmeleitpaste 1

Lüfterklammern 6

Y-Kabel 1

Legen Sie die Kühler-Montagebrücke (6) mittig auf den Kühler

(1). Anschließend platzieren Sie den Kühler auf der CPU.

Drehen Sie die beiden mittig positionierten Heatpipe-Caps auf

der Oberseite des Kühlers ab.

Ziehen Sie die Schrauben der Kühler-Montagebrücke ab-

wechselnd fest. Hierzu können Sie den Kreuzschraubenzieher

(9) benutzen.

Befestigen Sie den 120mm Lüfter (3) mit Hilfe der

Lüfterklammern (11) auf der Vorderseite des Kühlers. Den

135mm Lüfter (2) schieben Sie zwischen den beiden

Kühlkörpern entlang und befestigen auch diesen mit den

Lüfterklammern (11). Verbinden Sie die beiden Lüfter über

das Y-Kabel (12) und schließen Sie dieses an den CPU

Lüfteranschluss des Mainboards an.

Zur Demontage der Lüfter drücken Sie die Kerben der

Lüfterklammern (11) vom Lüfter weg.

Allgemeines

Für die Montage des Kühlers empfehlen wir

die Installation außerhalb des Gehäuses.

Aufbau des Kühlerbefestigungsrahmens

Platzieren Sie über die Vorderseite die vier TR4 Abstands-

bolzen (7) auf die Bolzen des Sockels und ﬁ xieren die lange

TR4 Montagebrücke (4) mit Hilfe der TR4 Schrauben (8).

Wiederholen Sie anschließend den Vorgang auf der gegen-

überliegenden Seite mit der kurzen TR4 Montagebrücke (5).

Montage des CPU-Kühlers

Entfernen Sie zunächst die Schutzfolie von der Unterseite

des Kühlers. Tragen Sie die Wärmeleitpaste (10) auf die CPU

Oberﬂ äche auf. Der Inhalt reicht für ca. 1 – 2 Anwendungen.

Vorsicht: Die mitgelieferte Wärmeleitpaste ist nicht zum

Verzehr geeignet. Bei Verzehr ausreichend Wasser trinken und

umgehend einen Arzt aufsuchen. Außerhalb der Reichweite

von Kindern aufbewahren. Vermeiden Sie Haut- und

Augenkontakt.