Benning CM 2-1 Manual de Usario
Benning
multimetro
CM 2-1
Lee a continuación 📖 el manual en español para Benning CM 2-1 (44 páginas) en la categoría multimetro. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/44
BENNING CM 2-1
Operating manual
Translation of the German original version
5191 / 07/2021 en
Legal notice
5191 / 07/2021 enBENNING CM 2-12
Legal notice
Notes concerning the documentation
Ensure that the applicable documentation is used for this product. For safe handling, knowledge
that is provided in these instructions is required.
The product may only be handled while following this documentation, particularly the safety
instructions and warnings it contains. The personnel must be qualified for the respective task
and have the capability to recognise risks and prevent possible dangers.
Manufacturer and holder of rights
BENNING Elektrotechnik und Elektronik GmbH&Co.KG
Münsterstraße135–137
46397 Bocholt
Germany
Phone: +492871/93‑0
E-Mail: duspol@benning.de
Internet: www.benning.de
Commercial register Coesfeld HRA No. 4661
Copyright
© 2021, BENNING Elektrotechnik und Elektronik GmbH&Co.KG
All rights reserved.
This document – particularly all of the contents, texts, photographs and graphics that it contains
– are protected by copyright.
No part of this documentation or the associated contents may be reproduced or edited, copied
or distributed using electronic media in any form (printed, photocopied or using any other
method) without express written permission.
Disclaimer
The contents of the documentation has been checked to ensure that it corresponds to the
hardware and software described. Nevertheless, deviations cannot be ruled out, so Benning
cannot guarantee complete correspondence. The contents of this documentation are checked
at regular intervals, and any corrections that are needed are contained in the versions that
follow.
General non-discrimination
Benning is aware of the importance of language with regard to the equality of men and women,
and endeavours to take this into account at all times. To improve readability, we have refrained
from consistently using differentiating formulations.
Table of contents
Table of contents
1 Introduction................................................................................................................................................7
1.1 General notes........................................................................................................................7
1.2 History ...................................................................................................................................8
1.3 Service & support..................................................................................................................9
2 Safety........................................................................................................................................................10
2.1 Warning system ..................................................................................................................10
2.2 Standards applied ...............................................................................................................10
2.3 Symbols used......................................................................................................................11
2.4 Intended use .......................................................................................................................12
2.5 Special types of risks ..........................................................................................................14
3 Scope of delivery.....................................................................................................................................15
4 Device description...................................................................................................................................17
4.1 Device structure ..................................................................................................................17
4.2 Functions.............................................................................................................................20
4.2.1 “ACHFR/ DCAZERO” key ................................................................................................20
4.2.2 “HOLD / MIN MAX” key.......................................................................................................21
4.2.3 Further setting options ........................................................................................................21
4.3 Measuring ranges ...............................................................................................................22
4.3.1 Voltage ranges ....................................................................................................................23
4.3.2 Current ranges ....................................................................................................................24
4.3.3 Resistance ranges ..............................................................................................................24
4.3.4 Continuity test .....................................................................................................................24
4.3.5 Diode test ............................................................................................................................25
4.3.6 Capacitance ranges ............................................................................................................25
4.3.7 Frequency ranges ...............................................................................................................25
5 Operation..................................................................................................................................................26
5.1 Requirements for tests and measurements ........................................................................26
5.2 Connecting the safety measuring lines ...............................................................................27
5.3 Voltage or frequency measurement ....................................................................................28
5.4 Current or frequency measurement ....................................................................................30
5.5 Resistance measurement ...................................................................................................31
5.6 Continuity testing.................................................................................................................32
5.7 Capacitance measurement .................................................................................................32
5.8 Diode testing .......................................................................................................................33
5.9 Voltage indicator .................................................................................................................33
5.9.1 Non-contact phase testing ..................................................................................................34
5191 / 07/2021 en 3BENNING CM 2-1
Especificaciones del producto
| Marca: | Benning |
| Categoría: | multimetro |
| Modelo: | CM 2-1 |
¿Necesitas ayuda?
Si necesitas ayuda con Benning CM 2-1 haz una pregunta a continuación y otros usuarios te responderán
multimetro Benning Manuales
6 Septiembre 2024
6 Septiembre 2024
6 Septiembre 2024
4 Septiembre 2024
30 Agosto 2024
22 Agosto 2024
18 Agosto 2024
15 Agosto 2024
12 Agosto 2024
12 Agosto 2024
multimetro Manuales
- multimetro Alecto
- multimetro Appa
- multimetro Amprobe
- multimetro Amiko
- multimetro Silverline
- multimetro Ferm
- multimetro Workzone
- multimetro Stanley
- multimetro Yato
- multimetro Parkside
- multimetro Milwaukee
- multimetro EMOS
- multimetro Extech
- multimetro Tacklife
- multimetro Schneider
- multimetro Metrix
- multimetro Voltcraft
- multimetro Somogyi
- multimetro Velleman
- multimetro Steren
- multimetro Kyoritsu
- multimetro Ideal
- multimetro Flir
- multimetro Maxwell
- multimetro Digitus
- multimetro Testboy
- multimetro Hager
- multimetro Topcraft
- multimetro TFA
- multimetro Clas Ohlson
- multimetro Powerfix
- multimetro Owon
- multimetro Fluke
- multimetro Jung
- multimetro Projecta
- multimetro Etekcity
- multimetro Greenlee
- multimetro Högert
- multimetro Laserliner
- multimetro REV
- multimetro Testo
- multimetro Bruder Mannesmann
- multimetro Keithley
- multimetro Monacor
- multimetro Metrel
- multimetro Multimetrix
- multimetro Digi-tool
- multimetro Brandson
- multimetro GW Instek
- multimetro Skandia
- multimetro Elma
- multimetro Beha-Amprobe
- multimetro Vimar
- multimetro Uni-T
- multimetro Kewtech
- multimetro Strex
- multimetro Mastech
- multimetro PeakTech
- multimetro Sonel
- multimetro MBS
- multimetro MGL Avionics
- multimetro Chauvin Arnoux
- multimetro Megger
- multimetro Gossen Metrawatt
- multimetro Rigol
- multimetro PCE Instruments
- multimetro Micronta
- multimetro CEM
- multimetro Horex
- multimetro Cosinus
- multimetro Joy-it
- multimetro Klein Tools
- multimetro Aim TTi
- multimetro Kurth Electronic
- multimetro Wiha
- multimetro Weltron
- multimetro Sanwa
- multimetro Rohde & Schwarz
- multimetro EEVBlog
- multimetro Kingcraft
- multimetro Weidmüller
- multimetro HT Instruments
- multimetro Caltek
- multimetro Elworks
- multimetro Qian
- multimetro Bearware
- multimetro Noyafa
Últimos multimetro Manuales
22 Octubre 2024
21 Octubre 2024
18 Octubre 2024
18 Octubre 2024
17 Octubre 2024
16 Octubre 2024
16 Octubre 2024
16 Octubre 2024
16 Octubre 2024
16 Octubre 2024