Bertoni Uno Manual de Usario

Bertoni asiento de coche Uno

Lee a continuación 📖 el manual en español para Bertoni Uno (6 páginas) en la categoría asiento de coche. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
MANUAL INSTRUCTION
UNO
CAR SEAT
GROUP I, II, II
(9-36 kgs.)
ECE R44/04
WARNING!
Your child seat can only be fitted into the passenger seat of a car with a lap and diagonal
seat belt and without an airbag. Do not use any load bearing contact points other than
those described in the instructions and marked in the child restrarins.
The vehicle seat buckle is not positioned in or in front of the specified (labelled) belt
guide.
Important safety instructions!
WARNING! It is appropriate only if approved vehicles are equipped with a 3-point holding device of
safety belt, approved in accordance with Rule № 16 of the ECE at the UN or other equivalent
standards.
WARNING! The hard components or plastic parts of safety device for children should be deployed and
installed in way that during everyday use of the vehicle not be jammed by the movable seats or doors.
WARNING! All belts fastening car chair must be tight, belts restrain the child , must be adjusted to his
body and not twisted.
WARNING! The device must be replaced if it has undergone significant load of an accident.
WARNING! Waist belt has to be adjusted low so that child’s pelvis is restrained tight!
WARNING! It is dangerous to make changes or to supplement safety device without approval of the
competent authority!
WARNING! Follow closely the instructions for installation. Failure can result in injury to the child!
WARNING! Do not leave the child unattended in the safety device!
WARNING! Any luggage or other items that can cause injury if a collision should be properly secured!
WARNING! Safety device for children should not be used without case!
WARNING! Cases of seat should not be replaced with another, unless recommended by the
manufacturer, because it is an integral part of the system for securing children!
WARNING! Reversed system for securing children must not be installed on places protected by air
bags.
Instructions for safe use and installation of the child car seat Group 1,2,3
Child car seat suitable for children from 9 to 36 kg /Group 1,2,3/
WARNING!
1. This is an "universally" securing device for children. It is approved in accordance with
Rule № 44 for general use in vehicles and is suitable for most but not all seats in cars.
2. Placing is correct if the vehicle manufacturer has declared in the Manual for the use of
the vehicle that in the vehicle may be placed "Universal" Safety devices for children of this
age group.
3. This securing device for children is classified as "universal" under more stringent
conditions than those applied in previous structures, which don’t have this remark.
4. If you have doubt, consult the manufacturer of safety equipment for children or the seller.
Washing Instructions
The covers are easily removable and can be cleaned by using neutral soap and cold
water.
Do not tumble dry, iron the covers. Do not use dry machine, just airing it.
The plastic parts can be cleaned by using a wet drapery, please do not use any solvate.
EN IMPORTANT! KEEP FOR FURTHER REFERENCES.
READ CAREFULLY!
PARTS AND FITTINGS
THE TYPE OF APPROVED SEAT BELT YOU MUST HAVE
Slot
Headrest
Back rest
Harness
Chest pad
Crotch pad
Seat cushion
Belt guide
Harness straps
Your child seat can only be installed forward
facing using a three-point lap and diagonal
seat belt in the front or rear passenger seat
of the car.
Seats belt route slots
Harness connector
Buckle
Harness adjuster lever
Harness adjuster strap
diagonal beit
lap belt
Headrest height
adjusting button
CORRECT SHOULDER STRAP HEIGHT
NO-Too high YES-Correct
Always check that the shoulder straps are at the correct height for your child.
The child s shoulders should always be below the slot for the harness.
NO-Too low
WARNING: DO NOT INSTAL THE CAR SEAT ON A PASSENGER SEAT EQUIPPED WITH AN AIR BAG!
CHANGING THE SHOULDER STRAP HEIGHT
1. Release the strap holding the backrest cover to gain access to the harness.
2. Slide off one of the harness straps from the harness connector.
3. From the front pull it through the slot in the backrest and fabric cover.
4. Tread the harness strap back through next hole up or down on the backrest.
5. Re-thread the harness strap back onto the harness connector at the back of the seat.
6. Repeat the same process with the other harness strap. Make sure both of the straps go through slots
at the same height.

Especificaciones del producto

Marca: Bertoni
Categoría: asiento de coche
Modelo: Uno

¿Necesitas ayuda?

Si necesitas ayuda con Bertoni Uno haz una pregunta a continuación y otros usuarios te responderán


asiento de coche Bertoni Manuales

Bertoni

Bertoni Uno Manual de Usario

7 Septiembre 2024

asiento de coche Manuales

Últimos asiento de coche Manuales

Foppapedretti

Foppapedretti IS0DINAMYK Manual de Usario

27 Octubre 2024
Giordani

Giordani Pegasus Plus 1/2/3 Isofix Manual de Usario

26 Octubre 2024
Caretero

Caretero Securo Manual de Usario

26 Octubre 2024
Caretero

Caretero Kamptos Manual de Usario

26 Octubre 2024
Caretero

Caretero Rio Manual de Usario

26 Octubre 2024
Caretero

Caretero Fortis Manual de Usario

26 Octubre 2024
Phil And Teds

Phil And Teds optimum Manual de Usario

25 Octubre 2024
Cosatto

Cosatto Zoomi 3 i-Size Manual de Usario

21 Octubre 2024
Lionelo

Lionelo Izzy Manual de Usario

20 Octubre 2024
Joie

Joie Every Stage FX Signature Manual de Usario

19 Octubre 2024