Binatone IDECT iRoam Manual de Usario

Binatone No categorizado IDECT iRoam

Lee a continuación 📖 el manual en español para Binatone IDECT iRoam (2 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Getting started
Help
General Information
1
2
3
Box Contents
IMPORTANT
Accessory headset only – requires a base unit to operate.
Charger
Power adapter
Headset
Getting started
Step 1. Connecting the charger
• Plug the power adapter pin into the charger.
• Plug the other end of the power adapter into a power outlet.
• Use only the provided power adapter.
TIPS
Do not place your phone in the bathroom or other humid areas.
IMPORTANT
Use only the power adapter supplied with the product.
Step 2. Installing and charging the wireless
headset
• Attach the ear hook to the headset body as indicated. The
ear hook can be attached according to your preference to
wear the headset on the left or right ear.
• Put the installed wireless headset on the base cradle all the
way to the end for ensuring effective charging before using.
When the wireless headset is fully charged, the LED on
headset will light on blue steadily.
Left ear: Right ear:
1
L9_QSG_US_EN_FR_ES.fm Page 1 Friday, July 23, 2010 1:05 PM
IRoam
User Guide
Noise interference on your radio or television
• Your registered base or charger may be too close. Move it
as far away from these objects as possible.
Overview of the Wireless
Headset
1 POWER/TALK ON/OFF
• In idle mode: Press to place a call. Press and hold to
power the wireless headset on or off.
• During a call: Press to end the call.
• During registration: Press to exit the registration
mode.
2 VOLUME UP/FLASH
• During a call: Press to increase the earpiece volume.
Press and hold to answer a second incoming call.
• During ringing: Press to increase the ringer volume.
3 VOLUME DOWN
• During a call: Press to decrease the
earpiece volume.
• During ringing: Press to decrease the ringer volume.
Wireless Headset LED
Indicators
Purple:
Steadily on: The wireless headset is unregistered.
Flashing: The wireless headset is registered but the base is
not available (searching or out of range).
Blue:
Steadily on: When the headset is seated in the base and fully
charged. Once the headset is successfully registered, the blue
light will flash on then off, for about three seconds at a time,
and emit a long beep.
Long flashing: The wireless headset is in idle mode and off
the base.
Double flashing: The wireless headset is on, and if the signal
becomes weak, three short beeps will be heard.
Continuously flashing: The wireless headset is ringing and
can be heard through the earpiece.
Red:
Steadily on: When the wireless headset is charging on the
base.
Long flashing: Indicates that the battery is low, the unit is not
on the base, and the headset will emit short double beeps.
Double flashing: Indicates that the battery is low while the
headset is in use and short double beeps will be emitted.
Triple flashing: Indicates powering on/off the headset and
three short beeps will be emitted through the earpiece.
Red/Blue:
Toggling display: The wireless headset is in registration
mode. When the headset is registered successfully, the
headset will beep for around 2 seconds.
Step 3. Registration
To work as the handset extension, the headset must be
Maximum 5 handsets or headsets can be registered.
• Press and hold FIND for 4 seconds on the base and then
release.
• Press and hold VOL+/FLASH together with VOL - until the
LED on wireless headset toggling between red and blue.
• Place the unregistered wireless headset on the charger.
• A long beep tone is generated and the LED on in blue for a
while if the registration is successful.
Help
Poor audio quality
• The registered base is too close to electrical appliances,
reinforced concrete walls or metal doorframes - move the
base away from any electrical appliances.
No ring tone
• The ring tone is deactivated.
• Increase the volume.
When the headset lost its link with the registered
base during a call
• Check if the power cord is connected properly into the
registered base.
• Check if the power adapter is connected properly into the
wall socket.
• Move the headset closer to the base. It may be out of
range.
• Reset the base by unplugging the unit’s electrical power.
Reset the headset by clicking into the reset hole. Wait for
around 15 seconds and re-plug the power again. Allow up
to one minute for the headset to synchronize with the
registered base again.
Printed in China
Version 1.0
2
L9_QSG_US_EN_FR_ES.fm Page 2 Friday, July 23, 2010 1:05 PM
registered to the base of the listed models on page 2. iDECT
1. Registering to series baseiDECT

Especificaciones del producto

Marca: Binatone
Categoría: No categorizado
Modelo: IDECT iRoam

¿Necesitas ayuda?

Si necesitas ayuda con Binatone IDECT iRoam haz una pregunta a continuación y otros usuarios te responderán


No categorizado Binatone Manuales

Binatone

Binatone IDECT iRoam Manual de Usario

24 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024