Black And Decker FS8500AG Manual de Usario
Black And Decker
Máquina de molienda
FS8500AG
Lee a continuación 📖 el manual en español para Black And Decker FS8500AG (9 páginas) en la categoría Máquina de molienda. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/9
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use.
Many accidents
are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with these
instructions, taking into account the working conditions and the work to be
performed.
Use of the power tool for operations different from those intended could
result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer.
A charger that is
suitable for one type of battery pack may create a risk of fire when used with another
battery pack.
b) Use power tools only with specifically designated battery packs. Use of any
other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects like
paper clips, coins, keys, nails, screws, or other small metal objects that can
make a connection from one terminal to another.
Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts eyes,
additionally seek medical help.
Liquid ejected from the battery may cause irritation
or burns.
6) Service
a) Have your power tool serviced by a qualified repair person using only identical
replacement parts.
This will ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR ALL OPERATIONS
Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or
Abrasive, Cutting-Off Operations
a) This power tool is intended to function as a grinder, sander, wire brush,
polisher or cut-off tool. Read all safety warnings, instructions, illustrations
and specifications provided with this power tool. Failure to follow all
instructions listed below may result in electric shock, fire and/or serious injury.
b) Do not use accessories which are not specifically designed and
recommended by the tool manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe operation.
c) The rated speed of the accessory must be at least equal to the maximum
speed marked on the power tool. Accessories running faster than their rated
speed can break and fly apart.
d) The outside diameter and the thickness of your accessory must be within the
capacity rating of your power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
e) The arbour size of wheels, flanges, backing pads or any other accessory
must properly fit the spindle of the power tool. Accessories with arbour holes
that do not match the mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
f) Do not use a damaged accessory. Before each use inspect the accessory
such as abrasive wheel for chips and cracks, backing pad for cracks, tear or
excess wear, wire brush for loose or cracked wires. If power tool or
accessory is dropped, inspect for damage or install an undamaged
accessory. After inspecting and installing an accessory, position yourself and
bystanders away from the plane of the rotating accessory and run the power
tool at maximum no-load speed for one minute. Damaged accessories will
normally break apart during this test time.
g) Wear personal protective equipment. Depending on application, use face
shield, safety goggles or safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and work shop apron capable of stopping small
abrasive or workpiece fragments. The eye protection must be capable of
stopping flying debris generated by various operations. The dust mask or respirator
must be capable of filtrating particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing loss.
h) Keep bystanders a safe distance away from work area. Anyone entering the
work area must wear personal protective equipment. Fragments of workpiece
or of a broken accessory may fly away and cause injury beyond immediate area of
operation.
i) Hold power tool by insulated gripping surfaces only, when performing an
operation where the cutting accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a “live” wire may make exposed metal parts of
the power tool “live” and shock the operator.
j) Position the cord clear of the spinning accessory. If you lose control, the cord
may be cut or snagged and your hand or arm may be pulled into the spinning
accessory.
k) Never lay the power tool down until the accessory has come to a complete
stop. The spinning accessory may grab the surface and pull the power tool out of
your control.
l) Do not run the power tool while carrying it at your side. Accidental contact with
the spinning accessory could snag your clothing, pulling the accessory into your
body.
m)Regularly clean the power tool’s air vents. The motor’s fan will draw the dust
inside the housing and excessive accumulation of powdered metal may cause
electrical hazards.
n) Do not operate the power tool near flammable materials. Sparks could ignite
these materials.
o) Do not use accessories that require liquid coolants. Using water or other liquid
coolants may result in electrocution or shock.
p) Do not use Type 11 (flaring cup) wheels on this tool. Using inappropriate
accessories can result in injury.
q) Always use side handle. Tighten the handle securely. The side handle should
always be used to maintain control of the tool at all times.
Causes and Operator Prevention of Kickback
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad,
brush or any other accessory. Pinching or snagging causes rapid stalling of the
rotating accessory which in turn causes the uncontrolled power tool to be forced in
the direction opposite of the accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the
edge of the wheel that is entering into the pinch point can dig into the surface of the
material causing the wheel to climb out or kick out. The wheel may either jump
toward or away from the operator, depending on direction of the wheel’s movement
at the point of pinching. Abrasive wheels may also break under these conditions.
Kickback is the result of tool misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below:
a) Maintain a firm grip on the power tool and position your body and arm to
allow you to resist kickback forces. Always use auxiliary handle, if provided,
for maximum control over kickback or torque reaction during start up. The
operator can control torque reaction or kickback forces, if proper precautions are
taken.
b) Never place your hand near the rotating accessory. Accessory may kickback
over your hand.
c) Do not position your body in the area where power tool will move if kickback
occurs. Kickback will propel the tool in direction opposite to the wheel’s movement
at the point of snagging.
d) Use special care when working corners, sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp edges or bouncing have a tendency to
snag the rotating accessory and cause loss of control or kickback.
e) Do not attach a saw chain woodcarving blade or toothed saw blade. Such
blades create frequent kickback and loss of control.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust
. Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can
cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs
and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators.
There is an increased risk of electric shock if your body is
earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool
will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current
device (RD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence of
drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have
the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench
or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables bet-
ter control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used.
Use of dust collection
can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The
correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool
that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools.
Such preventive safety measures reduce the risk of starting the power
tool accidentally.
INFORMATION YOU SHOULD KNOW
• Wait until grinding wheel reaches full speed before applying work.
• Hold grinder at proper angle, as shown in Figure 10 and 11.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE GARANTÍA.
ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL PRODUCTO.
CAT. NO. FS8500AG FORM NO. 496437-00 Rev. 1 JAN. ‘08
Copyright © 2008 Black & Decker Printed in China
4
4
4
4
4
4
4
4
4
4-
-
-
-
-
-
-
-
-
-1
1
1
1
1
1
1
1
1
1/
/
/
/
/
/
/
/
/
/
2
2
2
2
2
2
2
2
2
2
I
I
I
I
I
I
I
I
I
IN
N
N
N
N
N
N
N
N
NC
C
C
C
C
C
C
C
C
CH
H
H
H
H
H
H
H
H
H
A
A
A
A
A
A
A
A
A
AN
N
N
N
N
N
N
N
N
NG
G
G
G
G
G
G
G
G
GL
L
L
L
L
L
L
L
L
LE
E
E
E
E
E
E
E
E
EG
G
G
G
G
G
G
G
G
GR
R
R
R
R
R
R
R
R
RI
I
I
I
I
I
I
I
I
IN
N
N
N
N
N
N
N
N
ND
D
D
D
D
D
D
D
D
DE
E
E
E
E
E
E
E
E
ER
R
R
R
R
R
R
R
R
R
INSTRUCTION MANUAL
Catalog # FS8500AG
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF
YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO
BLACK & DECKER.
T
THANK
HANK YOU
YOU FOR
FOR CHOOSING
CHOOSING F
FIREST
IRESTORM
ORM ! G
! GO
OT
TO
O
WWW
WWW.F
.FIREST
IRESTORMT
ORMTOOLS
OOLS.
.COM
COM/P
/PRODUCT
RODUCTR
REGISTRA
EGISTRATION
TION
T
TO
OREGISTER
REGISTER YOUR
YOUR NEW
NEW PRODUCT
PRODUCT.
.
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations
Operations
a) Use only wheel types that are recommended for your power tool and the
specific guard designed for the selected wheel. Wheels for which the power tool
was not designed cannot be adequately guarded and are unsafe.
b) The guard must be securely attached to the power tool and positioned for
maximum safety, so the least amount of wheel is exposed towards the
operator. The guard helps to protect operator from broken wheel fragments and
accidental contact with wheel.
c) Wheels must be used only for recommended applications. For example: do
not grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for
peripheral grinding, side forces applied to these wheels may cause them to shatter.
d) Always use undamaged wheel flanges that are of correct size and shape for
your selected wheel. Proper wheel flanges support the wheel thus reducing the
possibility of wheel breakage. Flanges for cut-off wheels may be different from
grinding wheel flanges.
e) Do not use worn down wheels from larger power tools. Wheel intended for
larger power tool is not suitable for the higher speed of a smaller tool and may burst.
Additional Safety Warnings Specific for Abrasive Cutting-Off Operation
a) Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to
make an excessive depth of cut. Overstressing the wheel increases the loading
and susceptibility to twisting or binding of the wheel in the cut and the possibility of
kickback or wheel breakage.
b) Do not position your body in line with and behind the rotating wheel. When
the wheel, at the point of operation, is moving away from your body, the possible
kickback may propel the spinning wheel and the power tool directly at you.
c) When wheel is binding or when interrupting a cut for any reason, switch off
the power tool and hold the power tool motionless until the wheel comes to a
complete stop. Never attempt to remove the cut-off wheel from the cut while
the wheel is in motion otherwise kickback may occur. Investigate and take
corrective action to eliminate the cause of wheel binding.
d) Do not restart the cutting operation in the workpiece. Let the wheel reach full
speed and carefully reenter the cut. The wheel may bind, walk up or kickback if
the power tool is restarted in the workpiece.
e) Support panels or any oversized workpiece to minimize the risk of wheel
pinching and kickback. Large workpieces tend to sag under their own weight.
Supports must be placed under the workpiece near the line of cut and near the
edge of the workpiece on both sides of the wheel.
f) Use extra caution when making a “pocket cut” into existing walls or other
blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or
objects that can cause kickback.
Safety Warnings Specific for Sanding Operations
a) Do not use excessively oversized sanding disc paper. Follow manufacturers
recommendations, when selecting sanding paper. Larger sanding paper
extending beyond the sanding pad presents a laceration hazard and may cause
snagging, tearing of the disc or kickback.
Safety Warnings Specific for Polishing Operations
a) Do not allow any loose portion of the polishing bonnet or its attachment
strings to spin freely. Tuck away or trim any loose attachment strings. Loose
and spinning attachment strings can entangle your fingers or snag on the
workpiece.
Safety Warnings Specific for Wire Brushing Operations
a) Be aware that wire bristles are thrown by the brush even during ordinary
operation. Do not overstress the wires by applying excessive load to the
brush. The wire bristles can easily penetrate light clothing and/or skin.
b) If the use of a guard is recommended for wire brushing, do not allow any
interference of the wire wheel or brush with the guard. Wire wheel or brush
may expand in diameter due to work and centrifugal forces.
Additional Safety Information
•Do not use Type 1 flat cut-off abrasive or diamond wheels without proper guard. (Guard
not included with unit.)
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are NOT safety glasses.
Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED
SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3),
• ANSI S12.6 (S3.19) hearing protection,
• NIOSH/OSHA/MSHA respiratory protection.
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work.
To reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter
out microscopic particles.
• Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,
and other construction activities. Wear protective clothing and wash exposed
areas with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin
may promote absorption of harmful chemicals.
WARNING: Use of this tool can generate and/or disburse dust, which may cause serious
and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory
protection appropriate for the dust exposure. Direct particles away from face and body.
WARNING: Always wear proper personal hearing protection that conforms to ANSI
S12.6 (S3.19) during use. Under some conditions and duration of use, noise from this
product may contribute to hearing loss.
WARNING: Always use eye protection. All users and bystanders must wear eye
protection that conforms to ANSI Z87.1.
WARNING: When not in use, place grinder on a stable surface where it will not
move inadvertantly, roll or cause a tripping or falling hazard. The grinder may stand
upright on the battery pack but may be easily knocked over. Serious personal injury may
result.
CAUTION: To reduce the risk of personal injury, use extra care when working into a
corner or edge because a sudden, sharp movement of the tool may be experienced when
the wheel or other accessory contacts a secondary surface or a surface edge.
The label on your tool may include the following symbols.
V ..........................volts A..........................amperes
Hz ........................hertz W ........................watts
min ........................minutes ......................alternating current
......................direct current no ........................no load speed
..........................Class II Construction
........................
earthing terminal
........................safety alert symbol SPM ....................strokes per
.../min ....................revolutions or minute
reciprocations per minute
Extension Cord
When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of
power and overheating. The table below shows the correct size to use depending on cord
length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller
the gage number, the heavier the cord.
Motor
Your tool is powered by a Black & Decker specified motor. Be sure your power supply
agrees with the nameplate marking. A marking of 120 volts, 50/60 Hz or 120 volts, AC only
means that the tool is designed to operate on normal 120 volt house current. Voltage
decrease of more that 10% will cause loss of power and overheating. All Black & Decker
tools are factory tested. If this tool does not run, check the power supply.
ASSEMBLY
WARNING: To prevent accidental operation, turn off and unplug tool before
performing the following operations. Failure to do this could result in serious
personal injury.
Attaching the Wheel Guard - Fig. 2
WARNING: NEVER GRIND OR BRUSH WITHOUT GUARD IN PLACE.
• Place the tool on a table, with the spindle (9) facing up.
• Place the spring washer (8) over the spindle and locate it on the shoulder (10).
• Place the guard (4) onto the tool as shown.
• Place the flange (7) over the spindle with the protruding pips towards the guard. Make
sure that the holes in the flange align with the screw holes.
• Secure the flange with the screws (6). Make sure that the screws are fully tight and that
the guard can be rotated.
Removing the Wheel Guard (For Sanding Only) - Fig. 3
CAUTION: To prevent loss of control, do not set tool down until accessory has
completely stopped turning.
This tool is fitted with a guard. For sanding only, you can remove the guard as follows:
• Remove the outer flange, disc and inner flange if they have been attached.
• Use a screwdriver to remove the screws (6).
• Remove the flange (7), guard (4) and spring washer (8). Store these parts carefully.
1. On/off switch
Interrupteur Marche/Arrêt
Conmutador de encendido y apagado
2. Lock-on button
Bouton de verrouillage en position de marche
Botón de bloqueo en encendido
3. Side handle
Poignée latérale
Mango lateral
4. Spindle lock
Bouton de verrouillage de la broche
Seguro del eje
5. Guard
Dispositif de protection
Protector
66
7
8
4
14
12
13
11
7
14
12
11
7
14
12
11
7
A
B
1415
5
12
3
5 6 7
6
6
7
4
9
8
10
2
1
4
Minimum Gage for Cord Sets
Volts Total Length of Cord in Feet
120V 0-25 26-50 51-100 101-150
(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)
240V 0-50 51-100 101-200 201-300
(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)
Ampere Rating
More Not more American Wire Gage
Than Than
0 - 6 18 16 16 14
6 - 10 18 16 14 12
10 - 12 16 16 14 12
12 - 16 14 12 Not Recommended
10 11
9
7A 8
Adjusting the Guard
The guard can be rotated 90°.
• Rotate the guard as required.
Fitting the Side Handle
• A three position auxiliary handle (4) is furnished with your grinder and can be screwed
into either side of the grinder housing as well as into the top.
WARNING: This handle SHOULD BE USED AT ALL TIMES to maintain complete
control of the tool. Always make sure the handle is tight.
Fitting and Removing Depressed Center Wheels - Fig. 4 - 6
CAUTION: Never use any depressed-center wheels without the proper guard.
Fitting - Figure 4,5
• Fit the guard as described above.
• Place the inner flange (11) onto the spindle (7) as shown (fig. 4). Make sure that the
flange is correctly located on the flat sides of the spindle.
• Place the disc (12) onto the spindle (7) as shown (fig. 4). If the disc has a raised center
(13), make sure that the raised center faces the inner flange.
• Make sure that the disc locates correctly on the inner flange.
• Place the outer flange (14) onto the spindle. When fitting a grinding disc, the raised
center on the outer flange must face towards the disc (A in fig. 5). When fitting a cutting
disc, the raised center on the outer flange must face away from the disc (B in fig. 5).
• Keep the spindle lock (5) depressed and tighten the outer flange using the two-pin
spanner (15) (fig. 6).
• When using a depressed-center wheel, hold the tool so that an angle of approximately
30° exists between the wheel and the work.
• When using ready-mount or hubbed wheels, flanges are not required.
WARNING: Check rated speed on depressed-center wheel. Never use a wheel with
rated speed lower than the speed on the nameplate of the tool.
EDGE GRINDING
Edge grinding may be done with Type 27 depressed center wheels specifically designed for
this purpose. These wheels are available locally. They must not be subject to side pressure.
CAUTION: Wheels used for edge grinding may break if they bend or twist while being
used for cut-off work or deep grinding. To reduce the risk of serious injury, limit the use of
these wheels to shallow cutting and notching (less than 1/2 in. in depth). The open side of
the guard must be positioned away from the operator.
Removing - Figure 6
• Keep the spindle lock (5) depressed and loosen the outer flange (14) using the two-pin
spanner (15) (fig. 6).
• Remove the outer flange (14) and the disc (12).
Fitting Wire Cup Brushes & Stringer Bead/Cable Twist Brushes
Wire brushes screw directly on the spindle of the machine without the use of flanges.
When using wire brushes, thread firmly on spindle by hand.
Fitting Abrasive Discs
Use an abrasive disc with a backing pad for sanding with your angle grinder.
• Remove the guard.
• Place the flange, (backing pad and abrasive disc sold separately) and outer flange on the
spindle as shown in shows how to attach an abrasive disc with aFigure 7. Figure 7A
rubber backing pad.
• Tighten the abrasive disc as shown in by depressing the spindle lock buttonFigure 8
and turning the abrasive disc by hand.
OPERATION
WARNING: Let the tool work at its own pace. Do not overload.
Switching On and Off
• To switch the tool on, press the on/off switch (1).
• For continuous operation, press the lock-on button (2) and release the on/off switch.
• To switch the tool off, release the on/off switch. To switch the tool off in continuous
operation, press the on/off switch once more and release it.
WARNING: Do not switch the tool off while under load.
Overload
Overloading will cause damage to the motor of your angle grinder. This can happen if
your angle grinder is subjected to heavy use for prolonged periods of time. Do not in
any circumstances, attempt to exert too much pressure on your angle grinder to speed
up your work. The abrasive discs operate more efficiently when light pressure is
exerted, thus avoiding a drop in the speed of your angle grinder.
SANDING
Precautions to Take When Sanding Paint
• Sanding of lead based paint is NOT RECOMMENDED due to the difficulty of controlling
the contaminated dust. The greatest danger of lead poisoning is to children and pregnant
women.
• Since it is difficult to identify whether or not a paint contains lead without a chemical
analysis, we recommend the following precautions when sanding any paint:
Personal Safety
• No children or pregnant women should enter the work area where the paint sanding is being
done until all cleanup is completed.
• A dustmask or respirator should be worn by all persons entering the work area. The filter
should be replaced daily or whenever the wearer has difficulty breathing.
NOTE: Only those dustmasks suitable for working with lead paint dust and fumes
should be used. Ordinary painting masks do not offer this protection. See your local
hardware dealer for the NIOSH approved proper mask.
Environmental Safety
• Paint should be removed in such a manner as to minimize the amount of dust generated.
• Areas where paint removal is occurring should be sealed with plastic sheeting of 4 mils
thickness.
• Sanding should be done in a manner to reduce tracking of paint dust outside the work
area.
GENERAL INFORMATION
Helpful Hints
• Hold your angle grinder with one hand on the body and the other hand firmly around the
side handle as shown in Figure 9.
• Always position the guard so that as much of the exposed disc as possible is pointing
away from you.
• Be prepared for a stream of sparks when the disc touches the metal.
• Maintain an angle between the disc and work surface ( ) of approximately 30° whenFig. 10
grinding and 10°-15° when sanding ( Fig. 11) for best tool control, material removal, and
minimal loading.
CAUTION: Use extra care when grinding into a corner as a sudden, sharp movement of
the grinder may be experienced when the wheel contacts a secondary surface.
WARNING: Always wear eye protection while operating this power tool.
Maintenance
Cleaning
Blowing dust and grit out of the motor housing using compressed air is a necessary
maintenance procedure.
CAUTION: Dust and grit from metal grinding often accumulate on interior surfaces and
could create an electrical shock hazard if not cleaned out.
Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment should be performed by authorized service centers or other qualified service
personnel, always using identical replacement parts.
Lubrication
Black & Decker tools are properly lubricated at the factory and are ready for use. Tools
should be lubricated regularly every year depending on usage. (Tools used on heavy duty
jobs and tools exposed to heat may require more frequent lubrication.) This lubrication
should be attempted only by trained power tool repairperson's such as those at Black &
Decker service centers or in other qualified service personnel.
Accessories
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-54-HOW-TO (544-6986).
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
Service Information
Black & Decker offers a full network of company-owned and authorized service locations
throughout North America. All Black & Decker Service Centers are staffed with trained
personnel to provide customers with efficient and reliable power tool service.
Whether you need technical advice, repair, or genuine factory replacement parts, contact
the Black & Decker location nearest you. To find your local service location, refer to the
yellow page directory under "Tools—Electric" or call: 1-800-54-HOW TO.
Full Two-Year Home Use Warranty
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in
material or workmanship. The defective product will be replaced or repaired at no charge in
either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from
whom it was purchased (provided that the store is a participating retailer). Returns should
be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days
after the sale). Proof of purchase may be required. Please check with the retailer for their
specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may
be required. Black & Decker owned and authorized Service Centers are listed under
"Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights
and you may have other rights which vary from province to province. Should you have any
questions, contact the manager of your nearest Black & Decker Service Center. This
product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are
missing, call 1-800-544-6986 for a free replacement.
Special Warranty Note to Contractors:
FIRESTORMTM branded products are offered as high end consumer home use tools and
carry a . These tools are designed, manufactured and tested toHOME USE WARRANTY
meet or exceed the needs of the do-it-yourselfer in the execution of projects and repairs in
and around the home. With proper use they will provide the home owner with step up
power and performance well beyond their two year warranty. However, if you use tools for
a living and use FIRESTORMTM branded products or any of Black & Decker’s other
Consumer Home Use tools you should know that they ON THE JOBSITE CANNOT BE
COVERED UNDER OUR WARRANTY.
See ‘Tools-
Electric’
– Yellow Pages –
for Service &
Sales
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
1-800-544-6986
www.FireStormTools.com
TROUBLESHOOTING
Problem Possible Cause Possible Solution
• Unit will not start. • Cord not plugged in. • Plug tool into a working
outlet.
• Circuit fuse is blown. • Replace circuit fuse.
(If the product repeatedly
causes the circuit fuse to
blow, discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Circuit breaker is tripped. • Reset circuit breaker.
(If the product repeatedly
causes the circuit
breaker to trip,
discontinue use
immediately and have it
serviced at a Black &
Decker service center or
authorized servicer.)
• Cord or switch is damaged. • Have cord or switch
replaced at Black
& Decker Service Center
or Authorized Servicer
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
Especificaciones del producto
| Marca: | Black And Decker |
| Categoría: | Máquina de molienda |
| Modelo: | FS8500AG |
¿Necesitas ayuda?
Si necesitas ayuda con Black And Decker FS8500AG haz una pregunta a continuación y otros usuarios te responderán
Máquina de molienda Black And Decker Manuales
29 Septiembre 2024
23 Septiembre 2024
19 Septiembre 2024
18 Septiembre 2024
16 Septiembre 2024
12 Septiembre 2024
17 Agosto 2024
5 Agosto 2024
28 Julio 2024
28 Julio 2024
Máquina de molienda Manuales
- Máquina de molienda Bosch
- Máquina de molienda AEG
- Máquina de molienda DeWalt
- Máquina de molienda Silverline
- Máquina de molienda Ferm
- Máquina de molienda Ozito
- Máquina de molienda Gude
- Máquina de molienda Gorenje
- Máquina de molienda Makita
- Máquina de molienda Tryton
- Máquina de molienda Hitachi
- Máquina de molienda Vonroc
- Máquina de molienda Stanley
- Máquina de molienda Skil
- Máquina de molienda Yato
- Máquina de molienda Hilti
- Máquina de molienda ECG
- Máquina de molienda Ryobi
- Máquina de molienda Profitec
- Máquina de molienda Festool
- Máquina de molienda Metabo
- Máquina de molienda United Office
- Máquina de molienda Parkside
- Máquina de molienda Worx
- Máquina de molienda Meec Tools
- Máquina de molienda Milwaukee
- Máquina de molienda Hikoki
- Máquina de molienda Dremel
- Máquina de molienda ABB
- Máquina de molienda Hazet
- Máquina de molienda Einhell
- Máquina de molienda Maktec
- Máquina de molienda Bort
- Máquina de molienda Craftsman
- Máquina de molienda Yamato
- Máquina de molienda Power Craft
- Máquina de molienda Powerplus
- Máquina de molienda Genesis
- Máquina de molienda Bunn
- Máquina de molienda Trotec
- Máquina de molienda Eibenstock
- Máquina de molienda Gamma
- Máquina de molienda Kress
- Máquina de molienda Dolmar
- Máquina de molienda Flex
- Máquina de molienda Nuova Simonelli
- Máquina de molienda Pattfield
- Máquina de molienda Max
- Máquina de molienda Truper
- Máquina de molienda Solo
- Máquina de molienda Meister Craft
- Máquina de molienda Toolcraft
- Máquina de molienda RIDGID
- Máquina de molienda Proxxon
- Máquina de molienda Fein
- Máquina de molienda Goon
- Máquina de molienda Global
- Máquina de molienda Rikon
- Máquina de molienda Duro Pro
- Máquina de molienda Alpha Tools
- Máquina de molienda SW-Stahl
- Máquina de molienda Einhell Bavaria
- Máquina de molienda McKenzie
- Máquina de molienda Gladiator
- Máquina de molienda Rodcraft
- Máquina de molienda Bavaria By Einhell
- Máquina de molienda Chicago Pneumatic
- Máquina de molienda Mirka
- Máquina de molienda Classic Power
- Máquina de molienda Handwerk
Últimos Máquina de molienda Manuales
26 Octubre 2024
26 Octubre 2024
23 Octubre 2024
17 Octubre 2024
17 Octubre 2024
15 Octubre 2024
14 Octubre 2024
14 Octubre 2024
13 Octubre 2024
8 Octubre 2024