Black And Decker JS610GK Manual de Usario

Black And Decker máquina de aserrar JS610GK

Lee a continuación 📖 el manual en español para Black And Decker JS610GK (8 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

General Power Tool Safety Warnings

WARNING! Read all safety warnings and instructions. Failure to follow the

warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded) power

tool or battery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust

. Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while operating a power tool.

Distractions can

cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools.

Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such as pipes, radiators,

ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the

power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension cord suitable for

outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable, use a residual current

device (RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the influence of

drugs, alcohol or medication.

A moment of inattention while operating power tools

may result in serious personal injury.

b) Use personal protective equipment. Always wear eye protection.

Protective

equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have

the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the power tool on.

A wrench

or a key left attached to a rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at all times.

This enables better

control of the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing

and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of dust extraction and collection

facilities, ensure these are connected and properly used.

Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct power tool for your application.

The

correct power tool will do the job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it on and off.

Any power tool

that cannot be controlled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the battery pack from the

power tool before making any adjustments, changing accessories, or storing

power tools.

Such preventive safety measures reduce the risk of starting the power

tool accidentally.

d) Store idle power tools out of the reach of children and do not allow persons

unfamiliar with the power tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use.

Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc., in accordance with these

instructions, taking into account the working conditions and the work to be

performed.

Use of the power tool for operations different from those intended could

result in a hazardous situation.

5) Battery tool use and care

a) Recharge only with the charger specified by the manufacturer.

A charger that is

suitable for one type of battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

c) When battery pack is not in use, keep it away from other metal objects like paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from the battery, avoid contact. If

contact accidentally occurs, flush with water. If liquid contacts eyes, additionally

seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

SPECIFIC SAFETY RULES

•Hold power tools by insulated gripping surfaces when performing an operation

where the cutting tool may contact hidden wiring or its own cord. Contact with a "live"

wire will make exposed metal parts of the tool "live" and shock the operator.

•Use clamps or another practical way to secure and support the work piece to a

stable platform. Holding the work by hand or against your body leaves it unstable and

may lead to loss of control.

• Keep hands away from cutting area. Never reach underneath the material for any reason.

Hold front of saw by grasping the contoured gripping area. Do not insert fingers or thumb

into the vicinity of the reciprocating blade and blade clamp. Do not stabilize the saw by

gripping the shoe.

• Keep blades sharp. Dull blades may cause the saw to swerve or stall under pressure.

• When cutting pipe or conduit ensure that they are free from water, electrical wiring,

etc.

• Allow the motor to come to a complete stop before withdrawing the blade from the

kerf (the slot created by cutting). A moving blade may impact the workpiece causing a

broken blade, workpiece damage or loss of control and possible personal injury.

• Never hold work in your hand, lap or against parts of your body when sawing. The saw

may slip and the blade could contact the body causing injury.

• Keep handles dry, clean, free from oil and grease. This will enable better control of the

tool.

• Clean out your tool often, especially after heavy use. Dust and grit containing metal

particles often accumulate on interior surfaces and could create an electric shock hazard.

• Do not operate this tool for long periods of time. Vibration caused by the operating action

of this tool may cause permanent injury to fingers, hands, and arms. Use gloves to provide

extra cushion, take frequent rest periods, and limit daily time of use.

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities contains chemicals known to the State of California to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

•Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling,

and other construction activities. Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your mouth, eyes, or lay on the skin may

promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust, which may cause

serious and permanent respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for the dust exposure. Direct particles

away from face and body.

CAUTION: Wear appropriate hearing protection during use. Under some

conditions and duration of use, noise from this product may contribute to hearing loss.

WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety

glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS

WEAR CERTIFIED SAFETY EQUIPMENT:

•

ANSI Z87.1 eye protection (CAN/CSA Z94.3)

•

ANSI S12.6 (S3.19) hearing protection

•

NIOSH/OSHA/MSHA respiratory protection

SAFETY GUIDELINES - DEFINITIONS

It is important for you to read and understand this manual. The information it contains

relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols

below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury.

CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation

which, if not avoided, may result in property damage.

Symbols

The label on your tool may include the following symbols.

V ..........................volts A..........................amperes

Hz ........................hertz W ........................watts

min........................minutes ......................alternating current

......................direct current no........................no load speed

.......................... Class II Construction ........................earthing terminal

........................safety alert symbol .../min ..................revolutions or

reciprocations

per minute

First Aid Measures for Gel Components (JS510G, JS610G Only)

If gel within the comfort grip becomes exposed and results in skin contact wash with soap

and water; for eye contact, flush with flowing water. If swallowed, seek medical attention.

Material Safety Data Sheet (MSDS) available from 1-800-544-6986.

INSTRUCTION MANUAL

Catalog Numbers JS500, JS510G, JS590TP, JS600, JS610G, JS4000

VEA EL ESPAÑOL EN LA CONTRAPORTADA.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. LÉASE ESTE INSTRUCTIVO ANTESADVERTENCIA:

DE USAR EL PRODUCTO.

CAT. NO. JS500, JS510G, JS590TP, JS600, FORM NO. 490340-01 REV. 1

JS610G, JS4000

JS600, JS610GJS500, JS510G, JS590TP, JS4000

BEFORE RETURNING THIS PRODUCT

FOR ANY REASON PLEASE CALL

1-800-544-6986

BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A

BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A

SUGGESTION OR COMMENT, GIVE US ACALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.

THANK

HANK YOU

YOU FOR

FOR CHOOSING

CHOOSING B

BLACK

LACK &

DECKER

ECKER!

OWWW

WWW.B

.B LACKAND

LACKANDD

DECKER

ECKER.

.COM

COM/N

/NEW

EWO

OWNER

WNER

OREGISTER

YOUR NEW

NEW PRODUCT

PRODUCT.

FUNCTIONAL

DESCRIPTION- JS500,

JS510G, JS590TP, JS4000

1. Variable speed switch

2. Lock-on button

3. Saw blade locking lever

4. Saw blade support roller

5. Saw blade

6. Shoe plate

7. Shoe plate locking knob

8. Saw blade storage compartment

9. Dust blower

10. Dust extraction adaptor

(available on select models -

check packaging for inclusion)

11. Rip fence (available on select

models - check packaging for

inclusion)

FUNCTIONAL

DESCRIPTION - JS600,

JS610G

1. On/off switch

2. Lock-on button

3. Variable speed control knob

4. Orbital action”Turbo” selector

5. Saw blade locking lever

6. Saw blade support roller

7. Saw blade

8. Shoe plate

9. Shoe plate locking knob

10. Saw blade storage compartment

11. Dust blower

12. Dust extraction adaptor

(available on select models -

check packaging for inclusion)

13. Rip fence (available on select

models - check packaging for

inclusion)

5 4 7

Illustrations A, B for Model JS500, JS510G, JS590TP, JS4000

6 7

11 9

13 12

Ills. C, D, E, F for Model JS500, JS510G, JS590TP, JS4000 - Cont.

13 11

15 14

8 9

Illustrations G, H, I,J, K for Model JS600, JS610G

USE OF EXTENSION CORDS

Make sure the extension cord is in good condition before using. Always use the proper size

extension cords with the tool – that is, proper wire size for various lengths of cord and heavy

enough to carry the current the tool will draw. Use of an undersized cord will cause a drop in

line voltage resulting in loss of power and overheating. For proper size cords see chart

below.

MOTOR

Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your

tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A

rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC

power. This information is printed on the nameplate. Lower voltage will cause loss of power

and can result in over-heating. All Black & Decker tools are factory-tested; if this tool does

not operate, check the power supply.

SAVE THESE INSTRUCTIONS

ASSEMBLY - JS500, JS510G, JS590TP, JS4000

WARNING: Before attempting any of the following operations, make sure that the tool is

switched off and unplugged and that the saw blade has stopped. Used saw blades can be

hot.

Fitting the saw blade (fig. A)

- Hold the saw blade (5) as shown, with teeth facing forward.

- Push the lever (3) downwards.

- Insert the shank of the saw blade into the blade holder (10) as far as it will go.

- Release the lever.

- Adjust the blade support roller as described below.

Adjusting the blade support roller (fig. B)

After fitting the blade, you need to adjust the blade support roller (4).

- Turn the locking knob (7) in direction A.

Minimum Gage for Cord Sets

Volts Total Length of Cord in Feet

120V 0-25 26-50 51-100 101-150

(0-7,6m) (7,6-15,2m) (15,2-30,4m) (30,4-45,7m)

240V 0-50 51-100 101-200 201-300

(0-15,2m) (15,2-30,4m) (30,4-60,9m) (60,9-91,4m)

Ampere Rating

More Not more American Wire Gage

Than Than

0 - 6 18 16 16 14

6 - 10 18 16 14 12

10 - 12 16 16 14 12

12 - 16 14 12 Not Recommended

- Slide the blade support roller against the rear of the blade. The blade must locate in the

central recess of the roller.

- Turn the locking knob (7) in direction to lock the shoe plate in place.B

Connecting a vacuum cleaner to the tool (fig. C & D)

- Align the dust extraction adaptor (9) with the saw shoe as shown.

- Insert the ribs (12) into the slots (13).

- Rotate the adaptor until it locks into position. Make sure that the ribs (14) are correctly

seated.

- Connect the vacuum cleaner hose (11)(not supplied) to the adaptor.

Dust extraction is not possible when making bevel cuts.

USE

WARNING: Never use the tool when the saw shoe is loose or removed.

Adjusting the shoe plate for bevel cuts (fig.E)

The shoe plate can be set to a left or right bevel angle of up to 45°.

- Turn the locking knob (7) in direction to release the shoe plate (6).A

- Pull the shoe plate (6) backwards and set it to the required angle. You can use the scale or

a protractor to check the angle.

- Turn the locking knob (7) in direction to lock the shoe plate in place. B

To reset the shoe plate for straight cuts:

- Turn the locking knob (7) in direction to release the shoe plate (6).A

- Pull the shoe plate backwards and set it to an angle of approximately 0.

- Push the shoe plate forward.

- Turn the locking knob (7) in direction to lock the shoe plate in place. Make sure that theB

shoe plate is supported by the guide ribs.

Switching On and Off

- To switch the tool on, press the variable speed switch (1). The tool speed depends on how

far you depress the switch.

- For continuous operation, press the lock-on button (2) and release the variable speed

switch. This option is available only at full speed.

- To switch the tool off, release the variable speed switch. To switch the tool off, when in

continuous operation, press the variable speed switch once more and release it.

How to Use the Sightline®Feature (fig.F)

- Use a pencil to mark the cutting line.

- Position the jigsaw over the line (15).

Viewing from directly above the jigsaw the line of cut can be easily followed. Should this view

be restricted for any reason, the indent (16) can be used as an alternate cutting guide.

ASSEMBLY - JS600, JS610G

WARNING: Before attempting any of the following operations, make sure that the tool is

switched off and unplugged and that the saw blade has stopped. Used saw blades can be

hot.

Fitting the saw blade (fig. G)

- Hold the saw blade (7) as shown, with teeth facing forward.

- Push the lever (5) downwards.

- Insert the shank of the saw blade into the blade holder (12) as far as it will go.

- Release the lever.

Connecting a vacuum cleaner to the tool (fig. H & I)

- Align the dust extraction adaptor (11) with the saw shoe as shown.

- Insert the ribs (14) into the slots (15).

- Rotate the adaptor until it locks into position. Make sure that the ribs (16) are correctly

seated.

- Connect the vacuum cleaner hose (13) (not supplied) to the adaptor.

Dust extraction is not possible when making bevel cuts.

USE

WARNING: Never use the tool when the saw shoe is loose or removed.

Adjusting the shoe plate for bevel cuts (fig. J)

The shoe plate can be set to a left or right bevel angle of up to 45°.

- Turn the locking knob (9) in direction to release the shoe plate (8).A

- Pull the shoe plate (8) backwards and set it to the required angle. You can use the scale or

a protractor to check the angle.

- Turn the locking knob (9) in direction to lock the shoe plate in place. B

To reset the shoe plate for straight cuts:

- Turn the locking knob (9) in direction to release the shoe plate (8).A

- Pull the shoe plate backwards and set it to an angle of approximately 0.

- Push the shoe plate forward.

- Turn the locking knob (9) in direction to lock the shoe plate in place. Make sure that theB

shoe plate is supported by the guide ribs.

Variable Speed Control

- Set the variable speed control knob (3) to the required speed range. Use a high speed for

wood, medium speed for aluminum and PVC and low speed for metals other then aluminum.

Orbital Action Turbo Selector

- For fast and efficient straight cuts in wood, set the turbo orbital action selector (4) to “max”.

- For accurate straight and curve cutting and a smooth surface finish, set the turbo selector

(4) to “min”.

- The turbo orbital action selector (4) can also be set to the middle position between “max”

and “min” for a moderate speed of cut and finish.

Note: Orbital Action not recommended when scrolling.

Switching On and Off

- To switch the tool on, press the on/off switch (1).

- For continuous operation, press the lock-on button (2) and release the on/off switch.

- To switch the tool off, release the on/off switch. To switch the tool off, when in continuous

operation, press the on/off switch once more and release it.

How to Use the Sightline®Feature (fig.K)

- Use a pencil to mark the cutting line.

- Position the jigsaw over the line (17).

Viewing from directly above the jigsaw the line of cut can be easily followed. Should this view

be restricted for any reason, the indent (18) can be used as an alternate cutting guide.

HINTS FOR OPTIMUM USE

General

- Use a high speed for wood, a medium speed for aluminum and PVC and a low speed for

metals other then aluminum.

Sawing laminates

As the saw blade cuts on the upward stroke, splintering may occur on the surface closest to

the shoe plate.

- Use a fine-tooth saw blade.

- Saw from the back surface of the workpiece.

- To minimize splintering, clamp a piece of scrap wood or hardboard to both sides of the

workpiece and saw through this sandwich.

Sawing metal

- Be aware that sawing metal takes much more time than sawing wood.

- Use a saw blade suitable for sawing metal.

- When cutting thin metal, clamp a piece of scrap wood to the back surface of the workpiece

and cut through this sandwich.

- Spread a film of oil along the intended line of cut.

CAUTION: Do not use vacuum adapter when cutting metal. Metal filings will be hot and

may cause a fire.

Rip Fence

Ripping and circle cutting without a pencil line are easily done with a rip fence and circle

guide (available as standard equipment on some models or at extra cost).

Attaching Rip Fence (fig.L & M)

- Insert rip fence into slot on the right side of saw shoe as shown with cross bar facing down.

- Place screw (19) into hole in bottom of shoe.

- Align clamp bar (20) over screw with lipped edge facing down and pointing towards the rear

of the saw.

- Using a phillips screwdriver, run the screw into the threaded hole in the bar clamp.

- Adjust to width of cut and tighten screw.

Circle Cutting

- Insert rip fence into slot on the right side of saw shoe with cross bar facing up.

- Adjust rip fence so that distance from blade to hole in cross bar is the desired radius and

tighten screw.

- Place saw so that center of hole in cross bar is over center of circle to be cut (make pocket

cut, drill hole for blade or cut inward from edge of material to get blade into position).

- When saw is properly positioned, drive a small nail through hole in cross bar into exact

center of circle to be cut. Using rip fence as a pivot arm, begin cutting circle.

MAINTENANCE

Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;

never immerse any part of the tool into a liquid.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment should be performed by authorized service centers or other qualified service

personnel, always using identical replacement parts.

ACCESSORIES

Recommended accessories for use with your tool are available from your local dealer or

authorized service center. If you need assistance regarding accessories, please call:

1-800-544-6986.

WARNING: The use of any accessory not recommended for use with this tool could be

hazardous.

SERVICE INFORMATION

Black & Decker offers a full network of company-owned and authorized service locations

throughout North America. All Black & Decker Service Centers are staffed with trained

personnel to provide customers with efficient and reliable power tool service. Whether you

need technical advice, repair, or genuine factory replacement parts, contact the

Black & Decker location nearest you. To find your local service location, refer to the yellow

page directory under "Tools—Electric" or call: 1-800-544-6986.

FULL TWO-YEAR HOME USE WARRANTY

Black & Decker (U.S.) Inc. warrants this product for two years against any defects in

material or workmanship. The defective product will be replaced or repaired at no charge in

either of two ways.

The first, which will result in exchanges only, is to return the product to the retailer from

whom it was purchased (provided that the store is a participating retailer). Returns should

be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days

after the sale). Proof of purchase may be required. Please check with the retailer for their

specific return policy regarding returns that are beyond the time set for exchanges.

The second option is to take or send the product (prepaid) to a Black & Decker owned or

authorized Service Center for repair or replacement at our option. Proof of purchase may

be required. Black & Decker owned and authorized Service Centers are listed under

"Tools–Electric" in the yellow pages of the phone directory.

This warranty does not apply to accessories. This warranty gives you specific legal rights

and you may have other rights which vary from state to state. Should you have any

questions, contact the manager of your nearest Black & Decker Service Center. This

product is not intended for commercial use.

Free warning label replacement: If your warning labels become illegible or are missing,

call 1-800-544-6986 for a free replacement.

See ‘Tools-

Electric’

– Yellow Pages –

for Service &

Sales

Black & Decker (U.S.)

Inc.,

701 E. Joppa Rd.

Towson, MD 21286

U.S.A.

TROUBLESHOOTING

Problem Possible Cause Possible Solution

• Unit will not start. • Cord not plugged in. • Plug tool into a working

outlet.

• Circuit fuse is blown. • Replace circuit fuse.

(If the product repeatedly

causes the circuit fuse to

blow, discontinue use

immediately and have it

serviced at a Black &

Decker service center or

authorized servicer.)

• Circuit breaker is tripped. • Reset circuit breaker.

(If the product repeatedly

causes the circuit

breaker to trip,

discontinue use

immediately and have it

serviced at a Black &

Decker service center or

authorized servicer.)

• Cord or switch is damaged. • Have cord or switch

replaced at Black

& Decker Service Center

or Authorized Servicer

For assistance with your product, visit our website www.blackanddecker.com for the

location of the service center nearest you or call the BLACK & DECKER help line at

1-800-544-6986.

Especificaciones del producto

Marca:	Black And Decker
Categoría:	máquina de aserrar
Modelo:	JS610GK
Material de la carcasa:	Roestvrijstaal
Código de seguridad internacional (IP):	IP68
Soporte de colocación:	Buiten
Compatibilidad de marca:	Vivotek