Boston Acoustics SoundWare Manual de Usario

Lee a continuación 📖 el manual en español para Boston Acoustics SoundWare (4 páginas) en la categoría Vocero. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
SoundWare
High Performance Indoor / Outdoor Speaker
For great sound anywhere
Español
Gran sonido en cualquier lugar
Altavoz para interior/exterior
Francais
Un son sublime à tout endroit
Haut-parleur d’intérieur/extérieur
Italiano
Suono eccellente ovunque
Impianto di altoparlanti per
interni ed esterni
Svensk
Perfekt ljud överallt
Inom- och utomhushögtalare
Deutsch
Überall ein Riesensound
Innen-/Außenlautsprecher
Description
The Boston Acoustics® SoundWare is truly a go everywhere, do everything speaker. All of its parts
are weather resistant so they’re at home indoors and out, in situations from outdoor entertainment
to home theater. Compact size and a  exible mounting system give you many options for installation
locations. You can just set them on a shelf or use the supplied brackets and mount them in a corner
or on a  at wall. The pivoting mounts let you tilt and swivel the speakers to suit the installation. If one
of the available colors doesn’t work in your décor, then SoundWare can be painted in a matching or
complementary color. SoundWare – Great Sound Anywhere.
Speci cations
Frequency Response 90Hz-20kHz (±3dB)
Recommended Amp Power 15 – 100 watts
Nominal Impedance 8 ohms
Sensitivity 87dB
Woofer 4
12 (114mm) Driver
Tweeter 34 (20mm) dome
Crossover Frequency 3.5kHz
Net Weight 4.9 lbs (2.22kg)
Dimensions (H x W x D) 616 x 616 x 612 (157 x 157 x 167mm)
Placement Options
The SoundWare speaker can be wall mounted using the supplied hardware or simply placed on a
shelf. If it is being placed on a shelf you can simply attach the adhesive-backed rubber feet and
connect the speaker wires.
Attaching the Pivoting Ball Mount
If you plan to use the mounting brackets you must attach
the pivoting ball mount to the speaker. Use the four sup-
plied  at-head machine screws as shown in the illustration.
Mounting the Wall Bracket
Brackets for mounting the speakers on a  at wall or in a
corner are supplied. One thing that is not supplied is hard-
ware to attach the bracket to the wall. Why? Because there
are so many di erent kinds of surfaces on which the speakers could
be mounted. It could be basic drywall which may or may not have a
stud behind it. It could be a wood panel or even a concrete foundation
wall. There is no one type of fastener that we could supply that would
work in all the possible situations. So taking into account the surface the speaker is being mounted
on, acquire the appropriate type of fasteners. You’ll need four for each speaker. If you’re not sure what
type of fastener to use, take the mounting bracket to a friendly hardware store, tell them about the
wall you’re mounting the speaker on, and ask them to recommend an appropriate fastener. Keep in
mind the weight of the speaker.
En
E
N
G
L
I
S
H
The SoundWare speakers pivot on their mounts.
Vertically they can go from facing straight out to being
tilted down 40 degrees. When the  at wall mounting
bracket is used they can pivot side to side 20 degrees.
(Note: Corner mounting will not allow the speaker to
pivot side-to-side.) Loosen the pivot set screw on the
front of the pivoting ball mount, pivot the speaker into
position and retighten the screw.
Speaker Wires
For short runs of less then 20 feet or so you can use 16 gauge wire. But typically you should use
heavier 14 gauge wire. That is good enough for runs up to 50 feet or so. For runs of more than 50 feet
use 12 gauge wire.
Speaker Connection Polarity
All the speakers in a system must be hooked up with the same polarity or “in phase. The terminals on
the SoundWare speakers are color coded to identify the “+” (red) and “–” (black) connections. All wire
is marked in some way so you can tell one conductor from the other. The marking may be a ridge
molded into the insulation of one conductor, or it may have a stripe on the insulation, or it may be
color coded. Use the marking on the speaker wires to be sure that the “+” terminal of the ampli er is
connected to the “+” terminal of the speaker, and “–” is connected to “–”, at every connection.
Connecting the Speakers
Separate the two conductors of the wire. Remove
about 3/8” of insulation from the end of the wire. Push
down on the top of the terminal to open the hole for
the wire. Insert the wire and release the terminal to
secure it. Be sure there are no loose strands of wire.
Note: there is a channel in the back of the speaker for
the wire, to keep it neat and out of sight.
«ÛÌÃÊ
`ÜÊ{äc
«ÛÌÃÊÓäc
i>VÊÜ>ÞÊ
*ÛÌÊ-iÌ
-VÀiÜ
£
Ó
Mounting the Speakers
Once you have the bracket mounted and the speaker
connected the rest is easy.
1 Put the rounded end of the speaker mount in the
bracket and slide it down to lock it in place.
2 Optional – Insert and tighten the screw to secure
everything.
En
E
N
G
L
I
S
H

Especificaciones del producto

Marca: Boston Acoustics
Categoría: Vocero
Modelo: SoundWare

¿Necesitas ayuda?

Si necesitas ayuda con Boston Acoustics SoundWare haz una pregunta a continuación y otros usuarios te responderán




Vocero Boston Acoustics Manuales

Vocero Manuales

Últimos Vocero Manuales