Cannondale IQ300 Manual de Usario

Cannondale Computadora de bicicleta IQ300

Lee a continuación 📖 el manual en español para Cannondale IQ300 (6 páginas) en la categoría Computadora de bicicleta. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
THANK YOU FOR PURCHASING A CANNONDALE
Congratulations on your purchase of a Cannondale IQ Series computer.
Proper setup and operation will greatly enhance this product’s usefulness and your
enjoyment.
Please follow all Warnings and read all sections of this manual carefully and become fully
familiar with its operation before using it.
YOUR CANNONDALE RETAILER
Along with this manual, your key source of information and assistance is the shop where
you purchased this product. Your local Authorized Cannondale Retailer is your primary
contact to discuss service and adjustment to this product, instruction in its use, and any
warranty questions.
To nd an Authorized Cannondale Retailer closest to you, call 1800BIKEUSA. Or you can
use our dealer locator at our website www.cannondale.com.
IMPORTANT INFORMATION FOR ALL CANNONDALE CYCLING COMPUTERS
WARNINGS
WIRELESS COMPUTER MODELS (IQ200, IQ300, and IQ400) - People with medical/
implanted electronic equipment or devices such as heart pacemakers, EKG equipment,
etc. must not use wireless cycle computers due to possible risk of interference with the
medical devices.
EXERCISE - Adults with health problems (such as heart disease, diabetes or obesity) or
those at high risk, men over age 40 and women over age 50 or pregnant should talk
with their doctor before starting an exercise program.
INTENDED USE: For bicycle use only. Not for use on any motorized vehicle.
OPERATE COMPUTER ONLY WHEN NOT RIDING: Failure to pay attention to the road,
trail, trac or your surroundings could result in an accident, with risk of serious injury,
paralysis or death. You must focus on riding, not your computer. Learn computer opera-
tions, and do all possible computer operations when not riding. For any operations you
choose to perform while riding, choose a time and place where this distraction has less
risk.
MAKE SURE ALL COMPUTER PARTS ARE INSTALLED PROPERLY: The computer
must not interfere with the bicycle controls and your ability to use them. Mount the
computer according to the directions in this instruction manual. See your Authorized
Cannondale Retailer if you have any trouble installing or maintaining your computer.
CHECK FOR DAMAGE REGULARLY: Regularly check the position, alignment, and
condition of the spoke magnet, wireless sensor, cadence sensor, sensor and sensor wire
to make sure they are secure, aligned and in good condition. Make sure nothing is loose
and there are no worn or damaged parts.
BATTERIES: Use only battery size and type specied on the unit. Do not leave any
batteries in reach of children, and dispose of them correctly. If a battery is swallowed,
consult a doctor immediately.
NOT A TOY: Keep this computer and associated parts including the battery away from
children. Small parts could be swallowed.
YOU CAN BE SEVERELY INJURED, PARALYZED OR KILLED IN AN ACCIDENT IF YOU
IGNORE THESE WARNINGS.
NOTICE
■ This product is rain-proof only. Do not submerge or power wash.
■ Do not disassemble the unit.
■ Mount the computer according to the directions in this instruction manual.
■ Avoid direct impact to the computer unit.
■ Avoid using the computer unit in or near strong electromagnetic elds such as
high-voltage power lines or other transmitters.
■ Clean the unit with a mild detergent and a soft dry cloth. Never use any kind of
solvent or alcohol.
■ To prevent damage caused by battery leakage, remove the batteries before storage
or long period of non-use. Do not reverse battery installation. Observe positive (+)
and negative (-) markings.
■ WIRELESS MODELS (IQ200,IQ300, IQ400) Wireless computer uses an analog
wireless signal. It is not digitally coded but uses technology to lower the chance of
interference with circuitry used in other electronic devices such as lights, phones ,
computers, etc.
2012 IQ300 Computer
Setup and Owners Manual - 11/11
COMPUTER PARTS
COMPUTER INSTALLATION
The computer unit can be mounted on a bicycle handlebar or stem.
1. To mount the bracket, insert two nylon ties through the mounting bracket slots.
(a) - handlebar slots, (b) stem slots
2. Insert the rubber pad into back of mount bracket for handlebar or stem by aligning
slots in the back of the mount with the pad.
3. Position the pad/bracket onto the handlebar or stem and tighten both nylon ties
securely. Carefully snip tie ends 1-2mm from tie head.
To mount the computer onto the bracket, position it into the bracket at a 45 degree angle,
hold down and rotate the computer unit clockwise to lock it in place. To remove it, rotate
the computer counter-clockwise and lift it o.
NYLON TIES
MOUNTING BRACKET
HANDLEBAR
a
b
touch
touch
SENSOR INSTALLATION
Check the following components before installation:
1. Position the sensor on the front of the right fork leg within 60 cm of the computer. The
battery door must face out with the tear drop shape pointing down shown.
2. Pass the two cable ties through the sensor mounting holes and loosely mount the fork
sensor body to the left fork blade (do not fully tighten the cable ties at this point).
Loosely install the sensor magnet to one of the spokes of the front wheel. Adjust the
position of the magnet and sensor together so that the magnet is aligned with the line on
the bottom edge of the sensor and 1-2 mm separates the two parts and tighten both parts
in place.
Secure the sensor to the fork leg with two nylon ties.
3. Install the magnet onto a spoke so the magnet will pass over the sensor in the pickup zone
when the wheel is rotated.
4. Set the sensor-to-magnet gap by tilting the sensor toward or away from pickup zone. The
maximum distance between the speed sensor and magnet on the spoke is 5 mm.
5. When set, draw the nylon ties securely. Carefully snip the tie ends 1-2mm from tie head.
IQ300 COMPUTER UNIT
(back)
(front)
WIRELESS SENSOR
SPOKE MAGNET
NYLON TIES (X4)
MOUNTING PAD
MOUNTING BRACKET
(back)(front)
touch
MAX. 30 o
MAX.
60 cm
5 mm
MAX.
5 mm
SPOKE
MAGNET
PICK-UP ZONE
WIRELESS SENSOR
SENSOR
PROGRAMMING BUTTON
SENSOR
INDICATOR LED
2012 IQ300 Computer
Setup and Owners Manual - 11/11
NOTE: This computer can record information for 2 bikes with dierent wheel sizes. This
allows you to use 1 computer for 2 bikes. Shortly after the wheel rotates, the computer
automatically knows which bike is being used then provides accurate information for
speed and mileage. A mounting kit for a 2nd bike is sold separately. The following steps
only need to be done once.
To start programming:
1. Press until “ ” displays. FUNCTION ODO
2. Press and hold for >3 seconds to begin programming. SET
3. Press to change to “KM/H” or “M/H” SET
To program the computer for bike #1:
4. Determine your Tire Size then nd the corresponding L (mm) in the chart below.
5. Press to select bike 1 “SET ”
6. Press to move the cursor to the rst eld. FUNCTION
7. Press to change the 1st digit of 4 numbers for the L (mm). SET
Repeat steps 6 and 7 until the proper L (mm) is entered.
If you will use this computer for 2 bikes, continue to step 8.
If you will use it for only 1 bike, continue to step 10.
To program the computer for bike #2:
8. Determine your Tire Size then nd the corresponding L (mm) in the chart below.
9. Press to select bike 2 “FUNCTION ”
Repeat steps 6 and 7 until the proper L (mm) is entered.
10. Press and hold for 3 seconds to exit programming. FUNCTION
SETTING THE CLOCK (CLK)
1. Press FUNCTION until the “ ” function shows.CLK
2. Press and hold for >3 seconds to begin programming.SET
3. Press SET to change to “12H” or “24H” hour mode.
4. Press the to move the cursor to the hour eldFUNCTION
5. Press SET hour.
6. Repeat steps 4 and 5 to set Minutes and Seconds.
7. Press and hold the button for 3 seconds to exit programming.FUNCTION
GENERAL NOTES FOR PROGRAMMING ALL FUNCTIONS:
• Press and hold for 3 seconds to begin programming a function. SET
• Press the to change the value of a selected eld. Press/hold SET to change SET
value rapidly.
• Press the button to move the cursor to the next eld. FUNCTION
• Press and hold the button for 3 seconds to exit programming.FUNCTION
SETTING THE WHEEL SIZE
L (mm)
Tire Size L (mm) Tire Size L (mm)
24 X 1.75 1890 27 X 1-3/8 2169
24 X 2.00 1925 650 X 20C 1938
24 X 2.125 1965 650 X 23C 1944
26 X 7/8 1920 650 X 35A 2090
26 X 1(59) 1913 650 X 38A 2125
26 X 1(65) 1952 650 X 38B 2105
26 X 1.25 1953 700 X 18C 2070
Tire Size L (mm) 26 X 1-1/8 1970 700 X 19C 2080
14 X 1.50 1020 26 X 1-3/8 2068 700 X 20C 2086
14 x 1.75 1055 26 X 1-1/2 2100 700 X 23C 2096
16 X 1.50 1185 26 X 1.40 2005 700 X 25C 2105
16 X 1.75 1195 26 X 1.50 2010 700 X 28C 2136
18 X 1.50 1340 26 X 1.75 2023 700 X 30C 2146
18 X 1.75 1350 26 X 1.95 2050 700 X 32C 2155
20 X 1.75 1515 26 X 2.00 2055 2130700C Tubular
20 X 1-3/8 1615 26 X 2.10 2068 700 X 35C 2168
22 X 1-3/8 1770 26 X 2.125 2070 700 X 38C 2180
22 X 1-1/2 1785 26 X 2.35 2083 700 X 40C 2200
24 X 1 1753 26 X 3.00 2170 29 X 2.1 2288
24 X 3/4 Tubular 1785 27 X 1 2145 29 X 2.3 2326
24 x 1-1/8 1795 27 X 1-1/8 2155
24 X 1-1/4 1905 27 X 1-1/4 2161
To begin using the computer, simply press the button. Following installation, FUNCTION
the computer is activated automatically by a rotating wheel.
There are 2 power saving modes - 50% savings if no movement after 5 minutes, 100%
power savings after 30 minutes.
Press the button to exit the power saving modes prior to using the computer.SET
Press the button, to switch the computer through the following functions: FUNCTION
“CLK” – Clock feature, in 12/24 hr format
“TM” – Time ridden for 1 ride
“AVS” – Average speed for 1 ride
“MXS” – Maximum speed for 1 ride
“DST” - Distance ridden for 1 ride
“ODO” – Total miles ridden for all rides
“KCAL” – Calories burned (estimate) for 1 ride
“DAILY” -- DIstance ridden in the past 24 hours
“ODO 1” -- Total miles for all rides, bike 1 “ ”
“ODO 2” -- Total miles for all rides, bike 2 “ ”
To turn on the backlight, press and release the button. The backlight will stay SET
on for three (3) seconds.
“TM, AVS, MXS, DST, and KCAL “ are recorded automatically as soon as the wheel moves.
Recording stops if the wheel stops. To clear this information, press and hold the SET
button in the “TM” mode.
MAIN DISPLAY AND FUNCTIONS
C
R
2
0
3
2
touch
SET Button
(back of unit)
**This button also,
activates the display
backlighting.
CURRENT SPEED
SPEED SCALE
MODE
FUNCTIONS DISPLAY
FUNCTION Button
SUB-DISPLAY
TEMPERATURE
MOTION SIGNAL
BIKE “I or BIKE “II”
SLEEP MODE
2012 IQ300 Computer
Setup and Owners Manual - 11/11
TROUBLESHOOTING
CONDITION ACTION
Wheel moving but current speed does not
appear
Check/adjust sensor and magnet gap.
Battery is low –> replace
“ERR01” appears on display Battery low –> replace
“ERR” appears on display
Interference from another electronic
device-> turn o or move electronic
device
Display is blank, very light or black Battery low –> replace.
Computer too hot –> move to cool area.
Display changes slowly Computer too cold –> move to warm
area
NOTE: Touch feature is activated by nger pressure. If gloves are to thick, such
as winter gloves, the FUNCTION button may not be activated and require more
pressure.
NOTE: The computer uses a pencil tip sized free-oating sensor for auto on/o
features. If you hear a rattling noise during excessive vibration, it is normal and
the function will not be eected.
IQ300 Specications
Operating Temperature 0° C ~ 40° C, ( 32° F ~ 104°F)
Storage Temperature -10° C ~ 50° C, ( 14° F ~ 122°F)
Battery 3 volt lithium, CR2032 cell
Weight 30.6 grams
Timer Range: 0~29 (hour): 59 (minute): 59 (second)
Current Speed Range: 0 ~ 99.9 KM/ 0~62 Mile
Average Speed Range: 0 ~ 99.9 KM/ 0~62 Mile
MAX Speed Range: 0 ~ 99.9 KM/ 0 ~ 62 Mile
(Trip) Distance Range: 0 ~ 999.99 KM/ 0~600 Mile
Odometer Range: 0 ~ 99999 KM/ 0 ~ 62000 Mile
SETTING CALORIES BURNED (KCAL)
This computer can estimate calories burned while riding. The estimate is based on weight,
gender, time ridden and average speed. IMPORTANT: The estimate is truly an estimate.
Actual calories burned will vary depending on many variables the computer does not
calculate such as heart rate.
1. Press FUNCTION until the “ ” displays.KCAL
2 Press and hold for >3 seconds to begin programming.SET
3. Press SET to select gender “MALE” or “FEMALE”.
4. Press FUNCTION to store gender.
5. Press SET to change weight unit “Kg” or “Lb”.
6. Press FUNCTION to begin entering your weight in unit selected.
7. Press or hold Set to change the weight. Range: 0 ~ 150 Kg, 0-330 Lb.
8. Press and hold the Function for 3 seconds to exit programming.
RESETTING THE ODOMETER (ODO)
If the battery is replaced, it is possible to update the odometer to the mileage on your bike
after replacing the battery.
1. Press FUNCTION until the “ ” displays.ODO
2. Press and hold for >3 seconds to begin programming.SET
3. Press FUNCTION until “00000” (ve zeros) and “ ” appears on the screenODO
4. Press SET to change the appropriate numbers. Press to change cursor FUNCTION
position.
5. Repeat step 4 until the odometer is set.
6. Press and hold for 3 seconds to exit programming.FUNCTION
BATTERY REPLACEMENT
Remove the computer from the handlebar mount. Use a coin to unscrew the battery door.
Turn counter-clockwise. Remove the old battery. Place a new battery (CR2032) into the
computer with the positive “+” marking of the battery facing up. Replace the battery door.
Follow these steps for replacing the sensor battery (CR2032).
CANNONDALE USA
Cycling Sports Group, Inc.
172 Friendship Road,
Bedford, Pennsylvania, 15522 , USA
(Voice): 1-800-BIKE-USA
(Fax): 814-623-6173
custserv@cyclingsportsgroup.com
CANNONDALE EUROPE
Cycling Sports Group Europe, B.V.
mail: Postbus 5100
visits: Hanzepoort 27
7570 GC, Oldenzaal, Netherlands
(Voice): + 41 61.4879380
(Fax): 31-5415-14240
servicedeskeurope@cyclingsportsgroup.com
CANNONDALE AUSTRALIA
Cycling Sports Group Australia Pty Limited
Unit 8, 31-41 Bridge Road
Stanmore, NSW 2048, Australia
(Voice): 61-2-85954444
(Fax): 61-2-85954499
cannondale@cyclingsportsgroup.com.au
CANNONDALE JAPAN
Namba Sumiso Building 9F,
4-19, Minami Horie 1-chome,
Nishi-ku, Osaka 550-0015, Japan
(Voice): 06-6110-9390
(Fax): 06-6110-9361
cjcustserv@cannondale.com
CANNONDALE UK
Cycling Sports Group
Vantage Way, The Fulcrum,
Poole, Dorset, BH12 4NU
(Voice): +44 (0)1202 732288
(Fax): +44 (0)1202 723366
sales@cyclingsportsgroup.co.uk
CANNONDALE CONTACT INFORMATION
PROGRAMMING THE SENSOR
NOTE: These steps are only required if using the computer with a 2nd bike and only need
to be done once. Complete these steps after the computer is programed and the sensor
is installed.
1. Install the computer on Bike 2.
2. Press the blue SENSOR PROGRAMMING BUTTON on the back of the SENSOR INDICATOR
LED ashes. Release the button.
3. Lift the front wheel o the ground and spin it. The bike 1 icon “ ” will switch to the bike
2 icon “ ” and begin recording information for bike 2.
4. Verify nal set up for bike 2 “ by pressing the blue SENSOR PROGRAMMING BUTTON.
The LED will ash twice for bike 2.
5. To verify nal set up for bike 1, reinstall the computer on bike 1. Lift and spin the
front wheel to start the computer. Stop the wheel then press the blue SENSOR
PROGRAMMING BUTTON The SENSOR INDICATOR LED will ash 1 time to verify proper
function with bike 1.
SENSOR
PROGRAMMING
BUTTON
SENSOR
INDICATOR LED
SETTING THE TEMPERATURE
1. Press until “ ” displays.FUNCTION ODO
2. Press and hold for >3 seconds to begin programming. SET
3. Press repeatedly until “FUNCTION TEMP” displays.
Press SET to change Fahrenheit (F) or Celsius (C)
4. Press and hold for 3 seconds to exit programming. FUNCTION

Especificaciones del producto

Marca: Cannondale
Categoría: Computadora de bicicleta
Modelo: IQ300

¿Necesitas ayuda?

Si necesitas ayuda con Cannondale IQ300 haz una pregunta a continuación y otros usuarios te responderán


Computadora de bicicleta Cannondale Manuales

Cannondale

Cannondale IQ118 Manual de Usario

30 Agosto 2024
Cannondale

Cannondale IQ300 Manual de Usario

26 Agosto 2024

Computadora de bicicleta Manuales

Últimos Computadora de bicicleta Manuales

Bosch

Bosch Purion BUI215 Manual de Usario

18 Octubre 2024
BBB

BBB BCP-35W Manual de Usario

12 Octubre 2024
Crivit

Crivit HG01734A Manual de Usario

4 Octubre 2024
Sigma

Sigma Pure GPS Manual de Usario

2 Octubre 2024
Bryton

Bryton Rider 20 Manual de Usario

2 Octubre 2024
Lezyne

Lezyne Mega XL GPS Manual de Usario

30 Septiembre 2024
Sigma

Sigma BC 1600 Manual de Usario

30 Septiembre 2024
Cateye

Cateye Inou MSC-GC100 Manual de Usario

29 Septiembre 2024
Wahoo

Wahoo Elemnt Roam v2 Manual de Usario

24 Septiembre 2024
Trelock

Trelock BB 4000i Manual de Usario

23 Septiembre 2024