Casio 3180 Manual de Usario

Casio Mirar 3180

Lee a continuación 📖 el manual en español para Casio 3180 (6 páginas) en la categoría Mirar. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/6

Operation Guide 3180

MO0905- AE

Getting Acquainted

Congratulations upon your selection of this CASIO watch. To get the most out

of your purchase, be sure to read this manual carefully.

Keep the watch exposed to bright light

The electricity generated by the solar cell of the

watch is stored by a rechargeable battery. Leaving

or using the watch where it is not exposed to light

causes the battery to run down. Make sure the

watch is exposed to light as much as possible.

•When you are not wearing the watch on your

wrist, position the face so it is pointed at a

source of bright light.

•You should try to keep the watch outside of

your sleeve as much as possible. Charging is

reduced significantly if the face is covered only

partially.

Bright Light

Solar cell

All

functions

enabled

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Charge

Rechargeable battery

Bright Light

Electrical

energy

Solar cell

(Converts light to

electrical power.)

LEVEL 1

LEVEL 2

LEVEL 3

LEVEL 4

Some or all

functions

disabled

Dis-

charge

Battery charges in the light. Battery discharges in the dark.

•The watch continues to operate, even when it is not exposed to light.

Leaving the watch in the dark can cause the battery to run down, which will

result in some watch functions to be disabled. If the battery goes dead, you

will have to re-configure watch settings after recharging. To ensure normal

watch operation, be sure to keep it exposed to light as much as possible.

Note that CASIO COMPUTER CO., LTD. assumes no responsibility for

any damage or loss suffered by you or any third party arising through the

use of this product or its malfunction.

•The actual level at which some functions are disabled depends on the

watch model.

•Frequent display illumination can run down the battery quickly and require

charging. The following guidelines give an idea of the charging time

required to recover from a single illumination operation.

Approximately 5 minutes exposure to bright sunlight coming in through a

window

Approximately 8 hours exposure to indoor fluorescent lighting

•Be sure to read “Power Supply” for important information you need to

know when exposing the watch to bright light.

If the display of the watch is blank...

If the display of the watch is blank, it means that the watch’s Power Saving

function has turned off the display to conserve power.

•See “Power Saving Function” for more information.

About This Manual

•Depending on the model of your watch, display text appears either as dark

figures on a light background or light figures on a dark background. All

sample displays in this manual are shown using dark figures on a light

background.

•Button operations are indicated using the letters shown in the illustration.

•Each section of this manual provides you with the information you need to

perform operations in each mode. Further details and technical information

can be found in the “Reference” section.

General Guide

•Press C to change from mode to mode.

•In any mode, press L to illuminate the display.

Timekeeping Mode

Press C.

World Time Mode

Countdown Timer Mode Stopwatch Mode

Alarm Mode

▲

Timekeeping

Press the button to toggle the upper displayB

between the day of the week and date, and the

currently selected World Time city and time (Dual

Time).

Use the Timekeeping Mode to set and view the

current time and date.

Current Time

▲

Seconds

indicator

Hour : Minutes

Seconds

Day of week

Month – Day

Dual Time

▲

Dual time

City code

To set the time and date manually

1. In the Timekeeping Mode hold down untilA

the city code starts to flash, which indicates

the setting screen.

2. Use D and B to select the city code you

want.

•Make sure you select your Home City code

before changing any other setting.

•For full information on city codes, see the

“UTC Differential/City Code List”.

Read This Before You Set the Time and Date!

This watch is preset with a number of city codes, each of which represents

the time zone where that city is located. When setting the time, it is important

that you first select the correct city code for your Home City (the city where

you normally use the watch). If your location is not included in the preset city

codes, select the preset city code that is in the same time zone as your

location.

•Note that all of the times for the World Time Mode city codes are displayed

in accordance with the time and date settings you configure in the

Timekeeping Mode.

3. Press C to move the flashing in the sequence shown below to select the

other setting.

Seconds

12/24-Hour

Format Hour MinutesDST

Month Ye a r

City Code

DayPower Saving Illumination

Duration

Operation

Tone

4. When the timekeeping setting you want to change is flashing, use D or

B to change it as described below.

Specify your Home City

Cycle between Daylight Saving

Time (ON) and Standard Time

(OFF).

Use D (east) and B

(west).

Press D.

Screen: To do this: Do this:

Operation Guide 3180

5. Press A to exit the setting screen.

To specify your Home City

1. In the Timekeeping Mode, hold down untilA

the city code starts to flash, which indicates

the setting screen.

2. Press D (east) and B (west) to select the

city code you want to use as your Home City.

LIS, LON : Lisbon, London

MAD, PAR , ROM, BER, STO : Madrid, Paris,

Rome, Berlin, Stockholm

ATH : Athens

MOW : Moscow

HKG, BJS, TPE : Hong Kong, Beijing, Taipei

SEL, TYO : Seoul, Tokyo

HNL : Honolulu

ANC : Anchorage

YVR, LAX : Vancouver, Los Angeles

YEA DEN, : Edmonton, Denver

MEX CHI , : Mexico City, Chicago

NYC : New York

YHZ : Halifax

YYT : St.Johns

3. Press A to exit the setting screen.

City code

Hour : Minutes

PM indicator

Seconds

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour

from Standard Time. Remember that not all countries or even local areas use

Daylight Saving Time.

To change the Daylight Saving Time (summer time) setting

1. In the Timekeeping Mode, hold down untilA

the city code starts to flash, which indicates

the setting screen.

2. Press C and the DST setting screen appears.

3. Use D to cycle through the DST settings in

the sequence shown below.

DST off (

OFF

) DST on (

)

DST indicator

4. When the setting you want is selected, press to exit the setting screen.A

• The DST indicator appears to indicate that Daylight Saving Time is turned on.

12-hour and 24-hour timekeeping

•With the 12-hour format, the P (PM) indicator appears to the left of the hour

digits for times in the range of noon to 11:59 p.m. and no indicator appears

to the left of the hour digits for times in the range of midnight to 11:59 a.m.

•With the 24-hour format, times are displayed in the range of 0:00 to 23:59,

without the (PM) indicator.P

•The 12-hour/24-hour timekeeping format you select in the Timekeeping

Mode is applied in all other modes.

Others

•The day of the week is displayed automatically in accordance with the date

(year, month and day) settings.

•Button operation tone on and off

•Illumination duration

•Power Saving on and off

World Time

World Time shows the current time in 48 cities

(31 time zones) around the world.

•The times kept in the World Time Mode are

synchronized with the time being kept in the

Timekeeping Mode. If you feel that there is an

error in any World Time Mode time, check to

make sure you have the correct city selected

as your Home City. Also check to make sure

that the current time as shown in the

Timekeeping Mode is correct.

•Select a city code in the World Time Mode to display the current time in any

particular time zone around the globe. See the UTC Differential/City Code“

List” for information about the UTC differential settings that are supported.

•All of the operations in this section are performed in the World Time Mode,

which you enter by pressing C.

City code

Current time in

selected city

To view the time in another city

While in the World Time Mode, use the (eastward) and (westward)D B

buttons to scroll through the city codes (time zones). Holding down either

button scrolls at high speed.

•Pressing the D B and buttons at the same time will jump to the UTC time

zone.

To toggle a city code time between Standard Time and Daylight

Saving Time

1. In the World Time Mode, use D B and to

display the city code (time zone) whose

Standard Time/Daylight Saving Time setting

you want to change.

2. Hold down A to toggle between Daylight

Saving Time (DST indicator displayed) and

Standard Time (DST indicator not displayed).

•The DST indicator is shown on the World Time

Mode screen while Daylight Saving Time is

turned on.

DST indicator

•You can turn on DST individually for each city code, except UTC.

•Turning on DST for the city code that is currently selected as your Home

City will turn on DST for normal timekeeping.

Alarms

You can set up to five independent daily alarms

with hour and minutes. When an alarm is turned

on, the alarm tone sounds when the alarm time is

reached. One of the alarms is a snooze alarm,

while the other four are daily alarms.

You also can turn on an Hourly Time Signal that

causes the watch to beep twice every hour on the

hour.

•There are five alarm screens numbered AL1,

AL2 AL3 AL4, and for the daily alarm,

and a snooze alarm screen indicated by

SNZ.

The Hourly Time Signal screen is indicated by

SIG.

•All of the operations in this section are

performed in the Alarm Mode, which you enter

by pressing C.

Alarm number

Alarm time

(Hour : Minutes)

Current Time

To set an alarm time

1. In the Alarm Mode, use D to scroll through

the alarm screens until the one whose time

you want to set is displayed.

•To set a daily alarm, display alarm screen AL1, , AL2 AL3 or

AL4. To set the snooze alarm, display the screen.SNZ

•The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down until the hour setting of the alarmA

time starts to flash, which indicates the setting screen.

•This operation turns on the alarm automatically.

Toggle between 12-hour ( )

and 24-hour ( )

timekeeping

Reset the seconds to zero ( )

Change the hour and minutes

Change the year, month and day

Toggle between Button

Operation Tone on( ) and off

( )

Toggle the display illumination

duration between 1.5 seconds

( )) and three seconds (

Toggle between Power Saving

on ( ) and off ( )

Press D.

Use ).D (+) and B (–

Press D.

Screen: To do this: Do this:

3. Press C to move the flashing in the sequence shown below.

Hour Minutes

4. Use D (+) and B (–) to change the hour and minutes.

•With the 12-hour format, set the time correctly as a.m. or p.m. (P

indicator).

5. Press A to exit the setting screen.

Operation Guide 3180

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the

mode the watch is in. In the case of the snooze alarm, the alarm operation is

performed a total of seven times, every five minutes, until you turn the alarm

off.

•Alarm and Hourly Time Signal operations are performed in accordance with

the Timekeeping Mode time.

•To stop the alarm tone after it starts to sound, press any button.

•Performing any one of the operations below during a 5-minute interval

between snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the

SNZ

setting screen

To test the alarm

In the Alarm Mode, hold down to sound the alarm.D

To turn an alarm on and off

1. In the Alarm Mode, use to select an alarm.D

2. Press B to toggle it on and off.

•Turning on a alarm (AL1 AL2 AL3, , ,

AL4 SNZ or ) displays the alarm on indicator

( ) on its Alarm Mode screen.

•In all modes, the alarm on indicator is shown

for any alarm that is currently turned on.

•The alarm on indicator flashes and graphic

rotates while the alarm is sounding.

•The snooze alarm indicator ( ) flashes and

graphic rotates while the snooze alarm is

sounding and during the 5-minute intervals

between alarms.

Alarm on

indicator

Snooze alarm

indicator

ON Graphic

Area

To turn the Hourly Time Signal on and off

1. In the Alarm Mode, use to select theD

Hourly Time Signal (SIG).

2. Press B to toggle it on and off.

•The Hourly Time Signal on indicator ( ) is

shown on the display in all modes while this

function is turned on.

Hourly time signal

on indicator

Stopwatch

The stopwatch lets you measure elapsed time,

split times, and two finishes.

•The display range of the stopwatch is 23 hours,

59 minutes, 59.99 seconds.

•The stopwatch continues to run, restarting from

zero after it reaches its limit, until you stop it.

•The stopwatch measurement operation

continues even if you exit the Stopwatch Mode.

•Exiting the Stopwatch Mode while a split time is

frozen on the display clears the split time and

returns to elapsed time measurement.

•All of the operations in this section are

performed in the Stopwatch Mode, which you

enter by pressing C.

1/100 second

Hours

Minutes

Seconds

Start

Stop Re-start ClearStop

D D B

➤➤➤➤

Split

(SPL displayed)

Split release ClearStop

B D BB

➤➤➤➤

Split

First runner finishes.

Display time of first

runner.

Stop

Second runner

finishes.

ClearSplit release

Display time of

second runner.

D B BB

➤➤➤➤

To measure times with the stopwatch

Elapsed Time

Split Time

Two Finishes

Countdown Timer

You can set the countdown timer within a range

of one minute to 24 hours. An alarm sounds

when the countdown reaches zero.

•All of the operations in this section are

performed in the Countdown Timer Mode,

which you enter by pressing C.

Hours

Minutes

Seconds

To configure the countdown timer

1. While the countdown start time is on the

display in the Countdown Timer Mode, hold

down A until the current countdown start time

starts to flash, which indicates the setting

screen.

•If the countdown start time is not displayed,

use the procedure under “To use the

countdown timer” to display it.

2. Press C to move the flashing in the sequence shown below.

Hours Minutes

3. Use D (+) and B (–) to change the Hours and Minutes.

•To specify a countdown start time of 24 hours, set .

4. Press A to exit the setting screen.

To use the countdown timer

Press D while in the Countdown Timer Mode to

start the countdown timer.

•The countdown timer operation continues even

if you exit the Countdown Timer Mode.

•Press D while a countdown operation is in

progress to pause it. Press again to resumeD

the countdown.

•To stop a countdown operation completely, first

pause it (by pressing D B), and then press .

This returns the countdown time to its starting

value.

Countdown End Beeper

The countdown end beeper lets you know when the countdown reaches zero.

The beeper stops after about 10 seconds or when you press any button.

Seconds

Current

timer time

Timer start

time

Illumination

This watch has an EL (electro-luminescent) panel

that causes the entire display to glow for easy

reading in the dark. The watch’s auto light switch

turns on illumination automatically when you

angle the watch toward your face.

•The auto light switch must be turned on

(indicated by the auto light switch on indicator)

for it to operate.

•See “ ”Illumination Precautions for other

important information about using illumination.

To illuminate the display manually

In any mode, press to turn on illumination.L

•The above operation turns on illumination

regardless of the current auto light switch

setting.

Auto light switch

on indicator

•You can use the procedure below to select either 1.5 seconds or 3 seconds

as the illumination duration. When you press , the illumination will remainL

on for about 1.5 seconds or 3 seconds, depending on the current

illumination duration setting.

To specify the illumination duration

1. In the Timekeeping Mode, hold down untilA

the display contents start to flash. This is the

setting screen.

2. Press 10 times to display the currentC

illumination duration (LT1 or LT3).

3. Press to toggle the setting between DLT1

(1.5 seconds) and (three seconds).LT3

4. Press to exit the setting screen.A

Especificaciones del producto

Marca:	Casio
Categoría:	Mirar
Modelo:	3180

¿Necesitas ayuda?

Si necesitas ayuda con Casio 3180 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Mirar Casio Manuales

Casio Edifice EQB-1000TR-2AER Manual de Usario

24 Octubre 2024

Casio Collection MTP-1259PD-7BEF Manual de Usario

24 Octubre 2024

Casio G-Shock GA-810B-1A9ER Manual de Usario

24 Octubre 2024

Casio Collection SGW-450HD-1BER Manual de Usario

24 Octubre 2024

Casio Edifice EQB-1000XD-1AER Manual de Usario

24 Octubre 2024

Casio Collection MTP-1222A-2AVEF Manual de Usario

24 Octubre 2024

Casio G-Shock GMW-B5000G-2ER Manual de Usario

24 Octubre 2024

Casio Radio Controlled WV-200E-1AVEF Manual de Usario

24 Octubre 2024

Casio Collection LWS-2000H-2AVEF Manual de Usario

24 Octubre 2024

Casio Pro Trek PRW-60YBM-1AER Manual de Usario

24 Octubre 2024

Mirar Manuales

Últimos Mirar Manuales

Lorus W207 Manual de Usario

27 Octubre 2024

Invicta Specialty 31308 Manual de Usario

27 Octubre 2024

Timex Ironman TW5M244009J Manual de Usario

26 Octubre 2024

Timex MK1 TW2R68800VQ Manual de Usario

26 Octubre 2024

Braun BN0021 Manual de Usario

24 Octubre 2024

Braun AW60 Manual de Usario

24 Octubre 2024

Braun BN0042 Manual de Usario

24 Octubre 2024

Skmei 0984A Manual de Usario

22 Octubre 2024

Suunto SPARTAN ULTRA 1.2 Manual de Usario

21 Octubre 2024

Skmei 0955 Manual de Usario

21 Octubre 2024