Casio 5371 Manual de Usario

Casio Mirar 5371

Lee a continuación 📖 el manual en español para Casio 5371 (15 páginas) en la categoría Mirar. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/15

E-1

ENGLISH

Congratulations upon your selection of this CASIO watch.

Applications

The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.

Measured values are then shown on the display. Such features make this watch useful when hiking,

mountain climbing, or when engaging in other such outdoor activities.

Warning !

• The measurement functions built into this watch are not intended for taking measurements that

require professional or industrial precision. Values produced by this watch should be considered

as reasonable representations only.

•

When engaging in mountain climbing or other activities in which losing your way can create a

dangerous or life-threatening situation, always use a second compass to conﬁ rm direction readings.

• Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss

suffered by you or any third party arising through the use of this product or its malfunction.

E-2

Important!

• The watch’s Altimeter Mode calculates and displays relative altitude based on barometric pressure

readings produced by its pressure sensor. This means that readings taken at different times at the

same location may produce different altitude values due to changes in barometric pressure. Also note

that the value displayed by the watch may be different from the actual elevation and/or sea level

elevation indicated for the area where you are located.

• When using the altimeter of this watch for mountain climbing or other activities, it is highly

recommended that you check a map, local altitude indications, or some other source for your current

correct altitude and regularly calibrate the altimeter with the latest information. For more information,

see “To specify a reference altitude value” (page E-66).

• Whenever you use the digital compass of this watch for serious trekking, mountain climbing, or other

activities, be sure always to take along another compass to conﬁ rm readings. If the readings produced

by the digital compass of this watch are different from those of the other compass, perform bidirectional

calibration of the digital compass to ensure more accurate readings.

• Direction readings and digital compass calibration will not be possible if the watch is in the vicinity of a

permanent magnet (magnetic accessory, etc.), metal objects, high-voltage wires, aerial wires, or

electrical household appliances (TV, computer, cellphone, etc.)

E-3

About This Manual

• Depending on the model of your watch, digital display text appears

either as dark ﬁ gures on a light background, or light ﬁ gures on a dark

background. All examples in this manual are shown using dark ﬁ gures

on a light background.

• Button operations are indicated using the letters shown in the

illustration.

• Note that the product illustrations in this manual are intended for

reference only, and so the actual product may appear somewhat

different than depicted by an illustration.

Crown

Small hand

Second Hand

Minute HandHour Hand

Crown

Small hand

Second Hand

Minute HandHour Hand

E-4

Using the Crown

This watch has a lock-type crown.

Important!

• You should keep the crown locked during normal daily use. Leaving the crown unlocked creates the

risk of unintended operations or even damage due to impact.

To lock the crown

1. Push the crown back in (see “To pull out, rotate, or push the crown in”

below).

• Note that attempting to lock the crown when it is not pushed in can

cause unexpected watch operation.

2. Rotate the crown so Mark 1 is aligned with Mark 2.

3. While pushing in on the crown (a), rotate it to the right (b) until it stops,

and align Mark 1 with Mark 3.

4. Gently pull on the crown to make sure it is securely locked and does

not come out.

To unlock the crown

Rotate the crown so Mark 1 aligns with Mark 2.

Mark 2

Mark 1

Mark 3

Mark 2

Mark 1

Mark 3

E-5

To pull out, rotate, or push the crown in

Important!

• Before performing any of these operations, ﬁ rst unlock the crown.

The illustrations below show the different crown operations.

Pull out Rotate Push in

E-6

High-speed Movement

You can use either of the crown operations described below to move watch hands or indicators at high

speed.

HS1: Can be used to move both hands and display indicators.

HS2: Can be used when setting the hour and minute manually to move the hands at high speed.

To start HS1 high-speed movement

While the crown is pulled out, rotate it rapidly three turns away from you (for

forward movement) or towards you (for reverse movement). High-speed

movement will continue even if you release the crown.

To start HS2 high-speed movement

While HS1 high-speed movement is in progress, again rotate the crown rapidly

three turns in the same direction as the current HS1 movement (away from you

for forward movement or towards you for reverse movement).

To stop high-speed movement

Rotate the crown in the direction that is opposite that of the current high-speed

movement or press any button.

E-7

Note

• If you do not perform any operation for more than two minutes after pulling out the crown, the indicator

shown below will appear and crown operations will become disabled. If this happens, push the crown

back in and then pull it out again to re-enable crown operations.

• Even if the indicator shown below appears immediately after you pull out the crown, crown operations

are disabled. If this happens, push the crown back in and lock it.

1 second

• You can use high-speed movement in the following cases: when changing the time and/or date setting

in the Timekeeping Mode, Countdown Timer Mode, or Alarm Mode, or when performing magnetic

declination angle calibration, altitude calibration, barometric pressure calibration, or temperature

calibration operations.

Operation Guide 5371

E-8

Things to check before using the watch

1. Check the battery power level.

In any mode, hold down B for at least two seconds. The battery power indicator will appear on the digital

display, and then the watch will enter the Timekeeping Mode.

The battery power level will be indicated as H or M on the left

side of the digital display.

Go to step 2.

Power is low. Charge the watch by placing it in a location

where it is exposed to light. For details, see “Charging the

Watch” (page E-14).

NO YES

YES

Does any one of the following conditions exist?

• L flashing on the digital display.

• “ ” is flashing on the display.CHARGE

The watch is charged

sufficiently.

Battery power

indicator

•When L is ﬂ ashing, the second hand will jump at two-second intervals.

•When CHARGE is ﬂ ashing, all hands will move to and stop at 12 o’clock.

E-9

2. Check the Home City and the daylight saving time (DST) setting.

Use the procedure under “To conﬁ gure Home City and summer time settings” (page E-34) to conﬁ gure

your Home City and daylight saving time settings.

Important!

• Proper time calibration signal reception, and World Time Mode data depend on correct Home City,

time, and date settings in the Timekeeping Mode. Make sure you conﬁ gure these settings correctly.

3. Set the current time.

• To set the time using a time calibration signal

See “To get ready for a receive operation” (page E-22).

• To set the time manually

See “Conﬁ guring Current Time and Date Settings Manually” (page E-36).

The watch is now ready for use.

• For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic

Timekeeping” (page E-20).

E-10

Contents

About This Manual …………………………………………………………………………………………… E-3

Using the Crown ……………………………………………………………………………………………… E-4

To lock the crown ……………………………………………………………………………………… E-4

To unlock the crown …………………………………………………………………………………… E-4

To pull out, rotate, or push the crown in ……………………………………………………………… E-5

Things to check before using the watch ………………………………………………………………… E-8

Charging the Watch ………………………………………………………………………………………… E-14

To recover from the sleep state …………………………………………………………………… E-19

Radio Controlled Atomic Timekeeping ………………………………………………………………… E-20

To get ready for a receive operation ……………………………………………………………… E-22

To perform manual receive ………………………………………………………………………… E-24

To check the latest signal reception results ……………………………………………………… E-26

To turn auto receive on or off ……………………………………………………………………… E-27

Mode Reference Guide …………………………………………………………………………………… E-29

Timekeeping ………………………………………………………………………………………………… E-33

Conﬁ guring Home City Settings ………………………………………………………………………… E-34

To conﬁ gure Home City and summer time settings ……………………………………………… E-34

Conﬁ guring Current Time and Date Settings Manually ……………………………………………… E-36

To change the current time and date settings manually ………………………………………… E-36

To switch between 12-hour and 24-hour timekeeping …………………………………………… E-38

E-11

Hand Home Position Adjustment ……………………………………………………………………… E-39

To adjust home positions …………………………………………………………………………… E-39

Moving the Hands for Easy Viewing of the Digital Dials …………………………………………… E-40

To shift the hands and view digital info …………………………………………………………… E-40

Specifying Altitude, Barometric Pressure, and Temperature Units ……………………………… E-42

To specify altitude, barometric pressure, and temperature units ……………………………… E-42

Taking Barometric Pressure Readings ………………………………………………………………… E-43

To take barometric pressure readings …………………………………………………………… E-43

To show and hide barometric pressure differential ……………………………………………… E-45

To enable or disable the barometric pressure change indicator ……………………………… E-50

To calibrate the pressure sensor …………………………………………………………………… E-51

Taking Direction Readings ……………………………………………………………………………… E-53

To take a direction reading ………………………………………………………………………… E-53

To perform bidirectional calibration ………………………………………………………………… E-57

To perform magnetic declination correction ……………………………………………………… E-58

Using the Altimeter Mode ………………………………………………………………………………… E-62

To specify the altitude reading interval …………………………………………………………… E-63

To take altitude readings …………………………………………………………………………… E-64

To specify a reference altitude value ……………………………………………………………… E-66

To specify the altitude differential measurement range ………………………………………… E-68

To use the altitude differential value ……………………………………………………………… E-69

E-12

Taking Temperature Readings …………………………………………………………………………… E-73

To take temperature readings ……………………………………………………………………… E-73

To calibrate the temperature sensor ……………………………………………………………… E-75

Checking the Current Time in a Different Time Zone ………………………………………………… E-76

To enter the World Time Mode …………………………………………………………………… E-76

To conﬁ gure World Time City and summer time settings ……………………………………… E-77

To swap your Home City and World Time City …………………………………………………… E-79

To access the UTC (Universal Time Coordinated) time zone ………………………………… E-79

Checking the Tide Level and Moon Ages (Tide/Moon) ……………………………………………… E-80

To view the current tide level ……………………………………………………………………… E-80

To view a Moon age ………………………………………………………………………………… E-81

To view tide level and Moon age for a speciﬁ c date and time ………………………………… E-82

To calibrate the high tide time ……………………………………………………………………… E-85

Using the Stopwatch ……………………………………………………………………………………… E-88

To enter the Stopwatch Mode ……………………………………………………………………… E-88

To perform an elapsed time operation …………………………………………………………… E-88

To pause at a split time ……………………………………………………………………………… E-88

To measure two ﬁ nishes …………………………………………………………………………… E-89

E-13

Using the Countdown Timer ……………………………………………………………………………… E-90

To enter the Countdown Timer Mode ……………………………………………………………… E-90

To specify the countdown start time ……………………………………………………………… E-90

To perform a countdown timer operation ………………………………………………………… E-91

To stop the alarm …………………………………………………………………………………… E-91

Using the Alarm …………………………………………………………………………………………… E-92

To enter the Alarm Mode …………………………………………………………………………… E-92

To set an alarm time ………………………………………………………………………………… E-93

To turn an alarm and the Hourly Time Signal on and off………………………………………… E-94

To stop the alarm …………………………………………………………………………………… E-94

To test the alarm …………………………………………………………………………………… E-94

Illumination ………………………………………………………………………………………………… E-95

To turn on illumination manually …………………………………………………………………… E-95

To change the illumination duration ……………………………………………………………… E-96

To enable or disable the auto light switch ………………………………………………………… E-97

Other Settings ……………………………………………………………………………………………… E-99

To turn the button operation tone on or off ……………………………………………………… E-99

To turn Power Saving on or off …………………………………………………………………… E-99

Troubleshooting …………………………………………………………………………………………… E-100

Speciﬁ cations ……………………………………………………………………………………………… E-108

E-14

Charging the Watch

The face of the watch is a solar panel that generates power from light. The generated power charges a

built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed

to light.

Charging Guide

Whenever you are not wearing the

watch, leave it in a location where it

is exposed to light.

• Best charging performance is

achieved by exposing the watch to

the strongest light available.

When wearing the watch, make sure

that its face is not blocked from light

by the sleeve of your clothing.

• The watch may enter a sleep state

(page E-19) if its face is blocked

by your sleeve even only partially.

Warning!

Leaving the watch in bright light for charging can cause it to become quite hot.

Take care when handling the watch to avoid burn injury. The watch can become particularly hot

when exposed to the following conditions for long periods.

• On the dashboard of a car parked in direct sunlight

• Too close to an incandescent lamp

• Under direct sunlight

E-15

Important!

• Allowing the watch to become very hot can cause its liquid crystal display to go blank (totally black or

totally white, depending on the watch model). The appearance of the LCD should become normal

again when the watch returns to a lower temperature.

• Turn on the watch’s Power Saving function (page E-19) and keep it in an area normally exposed to

bright light when storing it for long periods. This helps to ensure that power does not run down.

• Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is

blocked from exposure to light can cause power to run down. Expose the watch to bright light

whenever possible.

Power Levels

In any mode, hold down B for at least two seconds. The battery power indicator will appear on the digital

display, and then the watch will enter the Timekeeping Mode.

You can get an idea of the watch’s power level by observing the battery power indicator on the display.

Level Battery Power Indicator Function Status

(H) All functions enabled.

(M) All functions enabled.

Battery power

indicator

Battery power

indicator

Operation Guide 5371

E-16

Level Battery Power Indicator Function Status

(L)

Functions below are disabled.

• Auto and manual receive

• Sensor operation

• Moon age

• Tide Graph, barometric pressure change

indicator

When the above functions are disabled,

the small hand stays at 9 o’clock.

• Illumination

• Beeper

Second hand jumps every two seconds.

(

CHARGE

)

All hands stopped at 12 o’clock.

All functions disabled.

5 – – –

All hands stopped at 12 o’clock.

All functions disabled and settings return

to their initial factory defaults.

• The ﬂ ashing L indicator at Level 3 (L) tells you that battery power is very low, and that exposure to

bright light for charging is required as soon as possible.

• Once the battery reaches Level 2 (M) after falling to Level 5, reconﬁ gure the current time, date, and

other settings.

• Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (M).

E-17

• Leaving the watch exposed to direct sunlight or some other very strong light source can cause the

battery power indicator to show a reading temporarily that is higher than the actual battery level. The

correct battery level should be indicated after a few minutes.

• The current time and all other settings return to their initial factory defaults whenever battery power

drops to Level 5 and when you have the battery replaced.

A dark environment while battery power is at Level 4 will cause the level to drop to Level 5. Expose the

watch to bright light whenever possible.

Low battery alert

When battery power reaches Level 3, the second hand of the watch will

jump at 2-second intervals in the Timekeeping Mode to let you know that

charging is required.

Power Recovery Mode

• Performing multiple sensor, illumination, or beeper operations during a short period may cause the

recovery indicator (RECOVER) to start ﬂ ashing on the display. This indicates that the watch is in the

power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and sensor

operations will be disabled until battery power recovers.

• Battery power will recover in about 15 minutes. At this time, the recovery indicator (

RECOVER) will stop

ﬂ ashing. This indicates that the functions listed above are enabled again.

Jumps at two-second

intervals

Jumps at two-second

intervals

E-18

• Frequent ﬂ ashing of the recovery indicator (RECOVER) indicates that battery power is low. Expose the

watch to bright light as soon as possible.

• Even if battery power is at Level 1 (

H) or Level 2 (M), the Digital Compass Mode, Barometer Mode,

Thermometer Mode or Altimeter Mode sensor may be disabled if there is not enough power available

to power it sufﬁ ciently. This is indicated when the recovery indicator (

RECOVER) are ﬂ ashing.

• Frequent ﬂ ashing of the recovery indicator (RECOVER) probably means that remaining battery power

is low. Leave the watch in bright light to allow it to charge.

Charging Times

Exposure Level (Brightness)

Daily

Operation

Level Change *2

Level 5 Level 4 Level 3 Level 2 Level 1

Outdoor sunlight (50,000 lux) 8 min. 3 hours 22 hours 6 hours

Sunlight through a window (10,000 lux)

30 min. 7 hours 82 hours 22 hours

Daylight through a window on a

cloudy day (5,000 lux) 48 min. 10 hours 133 hours 36 hours

Indoor ﬂ uorescent lighting (500 lux) 8 hours 118 hours – – – – – –

*1 Approximate amount of exposure time required each day to generate enough power for normal daily

operation.

*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.

• The above exposure times all are for reference only. Actual exposure times depend on lighting

conditions.

• For details about the operating time and daily operating conditions, see the “Power Supply” section of

the Speciﬁ cations (page E-111).

E-19

Power Saving

When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain

period in an area where it is dark. The table below shows how watch functions are affected by Power

Saving.

• For information about enabling and disabling power saving, see “To turn Power Saving on or off” (page

E-99).

• There actually are two sleep state levels: “display sleep” and “function sleep”.

Elapsed Time in Dark Hands and Display Operation

60 to 70 minutes (display sleep) Blank display, second hand

stopped.

Except for display and second hand, all

functions enabled.

6 or 7 days (function sleep) Blank display, all hands

stopped at 12 o’clock.

Except for timekeeping, all functions

disabled.

• The watch will not enter a sleep state between 6:00 a.m. and 9:59 p.m. If the watch is already in a sleep

state when 6:00 a.m. arrives, however, it will remain in the sleep state.

• The watch will not enter a sleep state while it is in the Stopwatch Mode or Countdown Timer Mode.

• The watch will not enter a sleep state while barometric pressure change indicator is enabled (page

E-50).

To recover from the sleep state

Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page

E-96).

E-20

Radio Controlled Atomic Timekeeping

This watch receives a time calibration signal and updates its time setting accordingly. However, when

using the watch outside of areas covered by time calibration signals, you will have to adjust the settings

manually as required. See “Conﬁ guring Current Time and Date Settings Manually” (page E-36) for more

information.

This section explains how the watch updates its time settings when the city code selected as the Home

City is in Japan, North America, Europe, or China, and is one that supports time calibration signal

reception.

If your Home City Code setting is this: The watch can receive the signal from the

transmitter located here:

LONDON (LON), PARIS (PAR), ATHENS (ATH) Anthorn (England), Mainﬂ ingen (Germany)

HONG KONG (HKG) Shangqiu City (China)

TOKYO (TYO) Fukushima, Fukuoka/Saga (Japan)

NEW YORK (NYC), CHICAGO (CHI), DENVER (DEN), LOS

ANGELES (LAX), ANCHORAGE (ANC), HONOLULU (HNL) Fort Collins, Colorado (United States)

Important!

• The areas covered by ANC and HNL

are quite far from the calibration signal transmitters, so certain

conditions may cause reception problems.

E-21

Approximate Reception Ranges

UK and German Signals

Anthorn

500 kilometers

1,500 kilometers

The Anthorn signal is

receivable within this area Mainflingen

North American Signal

Japanese Signals Chinese Signal

500 kilometers Changchun

Beijing

Shangqiu

Shanghai

Chengdu

Hong Kong

1,500 kilometers

2,000 miles

(3,000 kilometers)

600 miles

(1,000 kilometers)

Fort Collins

1,000 kilometers

For the Honolulu and Anchorage time zones, the

signal can be received when reception conditions

are favorable.

Fukuoka/Saga

500 kilometers

Fukushima

E-22

• Even when the watch is within range of a transmitter, signal reception may be impossible due to the

effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,

etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the

inﬂ uence of the conditions listed above becomes even greater.

• Signal reception may not be possible at the distances noted below during certain times of the year or

day. Radio interference may also cause problems with reception.

Mainﬂ ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)

Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)

Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)

Shangqiu (China) transmitter: 500 kilometers (310 miles)

• As of December 2013, China does not use Daylight Saving Time (DST). If China does go to the Daylight

Saving Time system in the future, some functions of this watch may no longer operate correctly.

To get ready for a receive operation

1. Conﬁ rm that the watch is in the Timekeeping Mode. If it isn’t, use B to enter the Timekeeping Mode

(page E-31).

2. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing

towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.

• Signal reception normally is better at night.

• The receive operation takes from two to ten minutes, but

in some cases it can take as long as 20 minutes. Take

care that you do not perform any button operation or

move the watch during this time.

12 o’clock

E-23

• Signal reception may be difﬁ cult or even impossible under the conditions described below.

Inside or

among

buildings

Inside a

vehicle

Near

household

appliances,

ofﬁ ce

equipment,

or a mobile

phone

Near a

construction

site, airport

Near

high-tension

power lines

Among or

behind

mountains

3. What you should do next depends on whether you are using auto receive or manual receive.

• Auto receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”

below for details.

• Manual receive: Perform the operation under “To perform manual receive” on page E-24.

Auto Receive

• With auto receive, the watch performs the receive operation each day automatically up to six times (up

to ﬁ ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to

the Timekeeping Mode time). When any receive operation is successful, none of the other receive

operations for that day are performed.

• When a calibration time is reached, the watch will perform the receive operation only if it is in the

Timekeeping Mode. The receive operation is not performed if a calibration time is reached while you

are conﬁ guring settings.

Operation Guide 5371

Especificaciones del producto

Marca:	Casio
Categoría:	Mirar
Modelo:	5371
Color del producto:	Zwart
Peso.:	6760 g
Ancho:	450 mm
Profundidad:	352 mm
Altura:	144 mm
Amable:	Draaitafel (dj) met directe aandrijving
Número de velocidades:	2
Puerto USB:	Ja
Forma:	S-vormige toonarm
Cubrir:	Ja
conexión USB:	Ja
Relación señal-ruido:	50 dB
velocidad nominal:	33 1/3, 45 RPM
PC conectada:	Ja
voltaje-de-entrada-de-CA:	115/230 V
Frecuencia-de-entrada-de-CA:	50/60 Hz
Consumo de energía (típico):	13 W
Tipo de motor:	DC-motor
Número de fases:	2
Incluye funda antipolvo:	Ja
Sistema de frenos:	Elektronische rem
Número de polos:	8
Material-del-tocadiscos:	Aluminium
longitud del brazo:	230.5 mm
Mantenga un registro del ángulo:	3 °
Sobresalir:	16 mm
tipo de brazo de dibujos animados:	Statisch gebalanceerde toonarm
Momento inicial:	1 kg/cm
Tipo motorborstel:	Borstelloos
Bereik anti-patinaje:	0 - 7 g
Remsnelheid (máx.):	1 s