Casio STL-S300H-1BEF Manual de Usario
Casio
reloj deportivo
STL-S300H-1BEF
Lee a continuación 📖 el manual en español para Casio STL-S300H-1BEF (7 páginas) en la categoría reloj deportivo. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/7
Operation Guide 3440 3441
MO1504-EB © 2015 CASIO COMPUTER CO., LTD.
E-1
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Keep the watch exposed to bright light
The electricity generated by the solar panel of the watch is
stored by a rechargeable battery. Leaving or using the
watch where it is not exposed to light causes the battery
to run down. Make sure the watch is exposed to light as
much as possible.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
• You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced signifi cantly
if the face is covered only partially.
l
l
l
l
l
l
l
l
l
l
l
Bright Light
Solar panel
E-2
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some
watch functions to be disabled. If the battery goes dead, you will have to
re-confi gure watch settings after recharging. To ensure normal watch operation, be
sure to keep it exposed to light as much as possible.
All
functions
enabled
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Charge
Rechargeable battery
Bright Light
Electrical
energy
Solar panel
(Converts light to
electrical power.)
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some or all
functions
disabled
Dis-
charge
Battery discharges in the dark.Battery charges in the light.
E-3
• The actual level at which some functions are disabled depends on the watch
model.
• Be sure to read “Power Supply” (page E-40) for important information you
need to know when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
• See “Power Saving Function” (page E-53) for more information.
About This Manual
• The operational procedures for Modules 3440 and 3441 are identical. All of the
illustrations in this manual show Module 3440.
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
E-4
[Module 3441][Module 3440]
C (Module 3440 charge indicator) CHG (Module 3441 charge indicator)
E-5
Contents
General Guide ………………………………………………………………………… E-8
To exit the demo mode …………………………………………………………E-10
Timekeeping ……………………………………………………………………………E-11
To set the time and date ………………………………………………………E-12
To change the Daylight Saving Time (summer time) setting ………………E-16
Stopwatch ………………………………………………………………………………E-17
To measure times with the stopwatch ………………………………………E-18
To position the lap time and split time on the display ………………………E-20
Recall Mode ……………………………………………………………………………E-22
To recall stopwatch records ……………………………………………………E-22
To delete a log …………………………………………………………………E-24
To delete all logs ………………………………………………………………E-25
E-6
Countdown Timer………………………………………………………………………E-26
To confi gure the countdown timer ……………………………………………E-27
To use the countdown timer ……………………………………………………E-29
World Time ………………………………………………………………………………E-30
To view the time in another city ………………………………………………E-31
To toggle a city code time between Standard Time and
Daylight Saving Time ………………………………………………………E-32
Alarms ……………………………………………………………………………………E-33
To set an alarm time ……………………………………………………………E-34
To test the alarm ………………………………………………………………E-35
To turn an alarm on and off ……………………………………………………E-36
To turn the Hourly Time Signal on and off ……………………………………E-37
Illumination ……………………………………………………………………………E-38
To illuminate the display manually ……………………………………………E-38
To specify the illumination duration……………………………………………E-39
E-7
Power Supply …………………………………………………………………………E-40
Reference ………………………………………………………………………………E-48
To turn the button operation tone on and off …………………………………E-52
To recover from the sleep state ………………………………………………E-54
To turn Power Saving on and off ………………………………………………E-54
Specifi cations …………………………………………………………………………E-57
E-8
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode
Stopwatch Mode
E-9
Recall Mode
Alarm Mode
Countdown Timer Mode
World Time Mode
Operation Guide 3440 3441
E-10
Demo Mode
In the Timekeeping Mode, holding down C for about three seconds will enter the
demo mode. In the demo mode, the screen cycles through the normal timekeeping,
stopwatch, and World Time screens in fi ve-second intervals.
To exit the demo mode
Press any button.
E-11
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
PM indicator
Day of week
Hour : Minutes Seconds
Year – Month – Day
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the time, it is important that you fi rst
select the correct city code for your Home City (the city where you normally use the
watch). If your location is not included in the preset city codes, select the preset city
code that is in the same time zone as your location.
• Note that all of the times for the World Time Mode city codes (page E-30) are
displayed in accordance with the time and date settings you confi gure in the
Timekeeping Mode.
E-12
To set the time and date
1. In the Timekeeping Mode, hold down A until the city
code starts to fl ash, which indicates the setting screen.
2. Use D and B to select the city code you want.
• Make sure you select your Home City code before
changing any other setting.
• For full information on city codes, see the “City
Code Table” at the back of this manual.
3. Press C to move the fl ashing in the sequence shown below to select the other
settings.
Seconds
12/24-Hour
Format Hour Minutes
DST
Month Year
City Code
DayPower Saving Illumination
Duration
Button
Operation Tone
E-13
• The following steps explain how to confi gure timekeeping settings only.
4. When the timekeeping setting you want to change is fl ashing, use D or B to
change it as described below.
Screen: To do this: Do this:
Change the city code Use D (east) and B
(west).
Toggle between Daylight Saving Time ( )
and Standard Time ( ) Press D.
Toggle between 12-hour ( ) and 24-hour
( ) timekeeping Press D.
Reset the seconds to Press D.
Change the hour and minutes Use
D (+) and B (–).
Change the year, month, or day Use
D (+) and B (–).
E-14
Screen: To do this: Do this:
/ Toggle the button operation tone between
(on) and (off) Press D.
Toggle the illumination duration between
(approximately 1.5 seconds) and
(approximately 3 seconds). Press D.
Toggle between Power Saving on ( ) and off
( ) Press D.
5. Press A to exit the setting screen.
• The day of the week is displayed automatically in accordance with the date (year,
month, and day) settings.
E-15
12-hour and 24-hour timekeeping
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits
for times in the range of noon to 11:59 p.m. and no indicator appears to the left of
the hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
any indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
E-16
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down A until the city
code starts to fl ash, which indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to cycle through the DST settings in the
sequence shown below.
'
4. When the setting you want is selected, press A to exit
the setting screen.
• The DST indicator appears to indicate that Daylight
Saving Time is turned on.
DST indicator
E-17
Stopwatch
The 1/100-second stopwatch can measure elapsed time
and lap/split times. Stopwatch times are stored in memory.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a lap/split time is
frozen on the display clears the lap/split time and
returns to elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing
& (page
E-8).
Note
• See page E-50 for information about the type of data
the watch stores in memory when you use the
stopwatch.
• Use the Recall Mode (page E-22) to view data stored in
memory.
Remaining memory
Split time
Lap time
E-18
To measure times with the stopwatch
Elapsed Time
D B D B B
Start Stop Resume Stop Reset
Lap/Split Times
D D D B B
Start Lap/Split Next Lap/
Split
Stop Reset
Lap/Split indicator
Lap time
Lap/Split indicator
Split time
E-19
Note
• Pressing D to perform a lap/split time operation freezes the lap/split time at that
point on the display for about eight seconds. After that, the display returns to
normal stopwatch time measurement.
• During a stopwatch time measurement operation, the current lap/split number is
shown at the top of the display, and the lap time and split time are shown in the
middle and at the bottom. You can change the positions of the lap time and split
time by pressing A while a stopwatch operation is in progress or stopped. For
details, refer to “To position the lap time and split time on the display” (page E-20).
Operation Guide 3440 3441
E-20
To position the lap time and split time on the display
Each press of A cycles the lap time and split time positions in the sequence shown
below.
• You can perform the above operation while stopwatch operation is ongoing or
stopped.
Lap time
Lap time
Hours Seconds
Minutes
Split time
Split time
Hours Seconds
Minutes
Split time
Lap time
Remaining memory
E-21
More than 10 hours
• Whenever the elapsed time exceeds 10 hours, the measurement changes from
1/100-second units to 1-second units.
E-22
Recall Mode
Use the Recall Mode to recall and delete records stored
by the Stopwatch Mode.
• Stopwatch records are stored in “logs” that are created
automatically by the watch. See “Memory Management”
on page E-48 for more information.
• The title screen of the newest log appears fi rst
whenever you enter the Recall Mode.
• Log numbers are automatically assigned in sequence,
starting from .
•
All of the operations in this section are performed in the
Recall Mode, which you enter by pressing C (page E-9).
To recall stopwatch records
In the Recall Mode, use A to scroll through the log title
screens, starting from the newest one, as shown below.
When the title screen of the log you want is displayed, use
D (+) and B (–) to cycle through the records contained
in the log.
Creation date
(Month – Day)
Log number
Time measurement
was performed
Log Title Screen
E-23
Stopwatch Record
Screen
Best Lap Time
Screen
Lap/Split number
Lap time
BEST indicator
Split time
Log Title Screen
E-24
• The locations of the lap time and split time in the Stopwatch Record screen are
determined by the display format you last selected in the Stopwatch Mode (page
E-17).
• The BEST indicator identifi es the record that contains the best lap time in the log.
• If a best lap time record is deleted automatically when the log becomes full, the
BEST indicator will not be transferred to the record with the next best lap time. See
“Memory Management” on page E-48 for more information about automatic deletion
of records.
To delete a log
1. In the Recall Mode, display the title screen or one of the records of the log you want
to delete.
2. While holding down B, hold down D for about two seconds until the watch beeps.
• “CLR” will fl ash on the display for two seconds and then the watch will beep.
Release B and D at this time.
• You cannot delete the log of an ongoing elapsed time measurement operation.
E-25
To delete all logs
While holding down B, hold down D for about fi ve seconds until the watch beeps
once and then a second time.
• “CLR” will fl ash on the display for two seconds and then the watch will beep once.
Keep B and D depressed and “ALL” will fl ash on the display for three seconds,
and then the watch will beep again. This indicates that all log data is cleared.
• You cannot delete logs while an elapsed timing operation is in progress.
E-26
Countdown Timer
Dual timers can be set with two different starting times.
The watch can be confi gured so the two timers alternate,
so when one reaches the end of its countdown, the other
timer starts. You can specify a “number of repeats” value,
which controls how many times the two-timer countdown
operation is performed (1 = once, 2 = twice, etc.). The
starting time of each timer can be set in fi ve-second steps
up to 99 minutes, 55 seconds.
You can specify up to 10 repeats. The watch emits a short
beep whenever either of the timers reaches the end of its
countdown during an ongoing timer operation. The watch
emits a 5-second beep when the end of the fi nal timer
operation (specifi ed by the number of repeats) is reached.
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 5 seconds or when you press any button.
Number of Repeats
Seconds
Timer 1Minutes
E-27
To confi gure the countdown timer
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to fl ash, which indicates the
setting screen.
• If the countdown start time is not displayed, use
the procedure under “To use the countdown timer”
(page E-29) to display it.
2. Press C to move the fl ashing in the sequence shown
below to select other settings.
Timer 1
Minutes Timer 1
Seconds Timer 2
Minutes Timer 2
Seconds
Number of Repeats
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
E-28
3. When the setting you want to change is fl ashing, use D and B to change it as
described below.
Setting Screen Button Operation
Minutes, Seconds UseD (+) and B (–) to change the setting.
Number of Repeats Use D (+) and B (–) to change the setting.
• To disable either timer, set 00'00" as its countdown start time.
4. Press A to exit the setting screen.
E-29
To use the countdown timer
Current repeat count Preset number of repeats
(Reset)
(Start/Stop)
Current timer time
Current time
Timer 1 or 2
Press D while in the Countdown Timer Mode to start the countdown timer.
• The countdown is performed by alternating between Timer 1 and Timer 2. A short
beep is emitted to signal a changeover from one timer to the other.
• Press D to pause a countdown. Press D again to resume.
• Pressing B while a countdown timer is stopped resets it to the start time specifi ed
by you.
• The watch emits a 5-second beep when the end of the fi nal timer operation
(specifi ed by the number of repeats) is reached.
• Even if you exit the Countdown Timer Mode, the countdown timer operation
continues and the watch beeps as required.
Especificaciones del producto
| Marca: | Casio |
| Categoría: | reloj deportivo |
| Modelo: | STL-S300H-1BEF |
¿Necesitas ayuda?
Si necesitas ayuda con Casio STL-S300H-1BEF haz una pregunta a continuación y otros usuarios te responderán
reloj deportivo Casio Manuales
24 Octubre 2024
27 Agosto 2024
27 Agosto 2024
24 Agosto 2024
18 Agosto 2024
12 Agosto 2024
26 Julio 2024
24 Julio 2024
21 Julio 2024
12 Julio 2024
reloj deportivo Manuales
- reloj deportivo Garmin
- reloj deportivo Adidas
- reloj deportivo Suunto
- reloj deportivo Silvercrest
- reloj deportivo Pyle
- reloj deportivo Crivit
- reloj deportivo Beurer
- reloj deportivo Timex
- reloj deportivo Bushnell
- reloj deportivo Medisana
- reloj deportivo Denver
- reloj deportivo Cateye
- reloj deportivo Cresta
- reloj deportivo Brigmton
- reloj deportivo Sunstech
- reloj deportivo Bryton
- reloj deportivo Polar
- reloj deportivo Fitbit
- reloj deportivo Kubo
- reloj deportivo Lamax
- reloj deportivo NGM
- reloj deportivo Sigma
- reloj deportivo TFA
- reloj deportivo TomTom
- reloj deportivo Withings
- reloj deportivo Ematic
- reloj deportivo Wahoo Fitness
- reloj deportivo Oppo
- reloj deportivo GolfBuddy
- reloj deportivo Guardo
- reloj deportivo Oregon Scientific
- reloj deportivo Misfit
- reloj deportivo EVOLVEO
- reloj deportivo Prixton
- reloj deportivo Goodis
- reloj deportivo Cubot
- reloj deportivo Fen
- reloj deportivo IZZO Golf
- reloj deportivo Bitween
- reloj deportivo Prologue
- reloj deportivo Soleus
- reloj deportivo Ronstan
Últimos reloj deportivo Manuales
18 Octubre 2024
17 Octubre 2024
11 Octubre 2024
10 Octubre 2024
7 Octubre 2024
5 Octubre 2024
5 Octubre 2024
5 Octubre 2024
4 Octubre 2024
29 Septiembre 2024