CDA KC73WH Manual de Usario
Lee a continuación 📖 el manual en español para CDA KC73WH (4 páginas) en la categoría Hundir. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
www.cda.eu
Ceramic Sinks
Installation
2
Installation
Before Installation
Oer up the sink to the worktop and/or the cabinets to confirm that
the external dimensions of the bowl are compatible with the cabinets
themselves.
Confirm that with the sink in position:
• There is adequate space to install any taps or other required
accessories.
• There is adequate space to install the waste pipework and that any
necessary modification to internal shelves to accommodate the waste
(and trap) is acceptable.
• Access to any water stop-cock or other services will still be adequate
after the installation.
Cutting the tap hole
Only cut/punch the tap hole from the top face of the sink.
• Select the tap hole position based on whether left hand or right hand
drainer is required.
• Locate the centre of the required tap hole by transferring
measurements from the cast in features on the underside. Cover the
top of the tap hole cut-out area with masking tape.
• Caution: Ensure that the sink is supported under the hole to be cut
out.
• Using a centre punch and hammer, make an initial cut in the glaze at
the centre of the required hole.
• Still using the punch and hammer enlarge the cut to the full hole size
required for the tap by carefully chipping away.
3
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
Installation
• Refer to the cut-out sizes on the back of this manual and use them
to mark out where the worktop needs to be cut. Double-check the
dimensions before cutting the worktop aperture.
• After cutting out the worktop aperture, we recommend you seal the
cut edges with silicone (or similar) sealant to help prevent ingress of
water.
• It is often easier to mount the taps, waste-fitting and overflow onto the
sink prior to fitting the sink to the worktop.
• Position the sink on the worktop, bedding it into a bed of silicone
sealant.
• After positioning the sink, leave it untouched for 24 hours to allow
the sealant to cure before any water is run into it.
• The taps, waste-fitting and overflow can now be mounted onto the
sink (if not already done) and fully connected to their respective
services.
• To check the waste for leaks, close the plug/basket of the waste
fitting, open the tap and fill the sink to the level of the overflow; turn
o the tap and wait several minutes to verify that the water doesn’t
drain away.
• Empty the sink.
After fitting, ensure that the enclosed “Ceramic Sinks Use and
Maintenance” guide is retained for the customer and/or user of the
sink.
Especificaciones del producto
| Marca: | CDA |
| Categoría: | Hundir |
| Modelo: | KC73WH |
¿Necesitas ayuda?
Si necesitas ayuda con CDA KC73WH haz una pregunta a continuación y otros usuarios te responderán
Hundir CDA Manuales
1 Septiembre 2024
31 Agosto 2024
28 Agosto 2024
28 Agosto 2024
28 Agosto 2024
27 Agosto 2024
27 Agosto 2024
27 Agosto 2024
27 Agosto 2024
27 Agosto 2024
Hundir Manuales
- Hundir Smeg
- Hundir Teka
- Hundir Hotpoint-Ariston
- Hundir Kernau
- Hundir Concept
- Hundir Blanco
- Hundir Rangemaster
- Hundir Gustavsberg
- Hundir Franke
- Hundir Leisure
- Hundir Nodor
- Hundir Elkay
- Hundir Schock
- Hundir Caple
- Hundir Roca
- Hundir Foster
- Hundir Advance Tabco
- Hundir Eagle Group
- Hundir Sani-Lav
- Hundir Laveo
- Hundir Deante
- Hundir Artusi
- Hundir Tot Mate
- Hundir Kuchinox
- Hundir Oliveri
- Hundir Shaws
Últimos Hundir Manuales
16 Octubre 2024
14 Octubre 2024
13 Octubre 2024
13 Octubre 2024
13 Octubre 2024
13 Octubre 2024
5 Octubre 2024
4 Octubre 2024
4 Octubre 2024
3 Octubre 2024