CDA KVF21R Manual de Usario
Lee a continuación 📖 el manual en español para CDA KVF21R (4 páginas) en la categoría Hundir. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : F : E : 01949 862 012 01949 862 003 customer.care@cda.eu www.cda.euW : www.cda.eu
kvf21 & kvf22
Stainless Steel
Flush Mount Sinks
Installation
2
Installation
Before Installation
Thoroughly check the sink and any fittings for signs of transport (or
other) damage. Please note: After fitting, sinks cannot be returned for
credit or replacement.
Oer up the sink to the worktop and/or the cabinets to confirm that
the external dimensions of the bowls are compatible with the cabinets
themselves.
Confirm that with the sink in position:
• There is adequate space to install any taps or other required
accessories.
• There is adequate space to install the waste pipework and that any
necessary modification to internal shelves to accommodate the waste
(and trap) is acceptable.
• Access to any water stop-cock or other services will still be adequate
after the installation.
Installation
• Refer to the cut-out sizes on the back of this manual and use them
to mark out where the worktop needs to be cut. Double-check the
dimensions before cutting the worktop aperture.
• After cutting out the worktop aperture, we recommend you seal the
cut edges with silicone (or similar) sealant to help prevent ingress of
water.
• It is often easier to mount the taps, waste-fitting and overflow onto the
sink prior to fitting the sink to the worktop.
• The edges of the sink should be bedded onto a bead of silicone
(or similar) sealant, to create a barrier to the ingress of water and
3
E & O E. All instructions, dimensions and illustrations are provided for guidance only. CDA reserve the
right to change specifications without prior notice.
other items between sink and
worktop.
• After positioning the sink on the
worktop, position the fixing brackets
as shown in Fig. 1, then tighten their
screws.
• Do not use a power tool to tighten
the screws; by using a hand tool
it is easier to ensure that they are
tightened just enough to clamp
down on the worktop and no more.
• After fixing, ensure the sealant forms a continuous bead to prevent
water ingress.
• Remove any excess sealant using an appropriate method as
recommended by the sealant manufacturer.
• The taps, waste-fitting and overflow can now be mounted onto the
sink (if not already done) and fully connected to their respective
services.
• To check the waste for leaks, close the plug/basket of the waste
fitting, open the tap and fill the sink to the level of the overflow; turn
o the tap and wait several minutes to verify that the water doesn’t
drain away.
• Empty the sink.
After fitting, ensure that the enclosed “Stainless Steel Sinks Use and
Maintenance” guide is retained for the customer and/or user of the
sink.
Fig. 1
Especificaciones del producto
| Marca: | CDA |
| Categoría: | Hundir |
| Modelo: | KVF21R |
¿Necesitas ayuda?
Si necesitas ayuda con CDA KVF21R haz una pregunta a continuación y otros usuarios te responderán
Hundir CDA Manuales
1 Septiembre 2024
31 Agosto 2024
27 Agosto 2024
26 Agosto 2024
24 Agosto 2024
24 Agosto 2024
23 Agosto 2024
21 Agosto 2024
21 Agosto 2024
21 Agosto 2024
Hundir Manuales
- Hundir Smeg
- Hundir Teka
- Hundir Hotpoint-Ariston
- Hundir Kernau
- Hundir Concept
- Hundir Blanco
- Hundir Rangemaster
- Hundir Gustavsberg
- Hundir Franke
- Hundir Leisure
- Hundir Nodor
- Hundir Elkay
- Hundir Schock
- Hundir Foster
- Hundir Advance Tabco
- Hundir Sani-Lav
- Hundir Deante
- Hundir Artusi
- Hundir Kuchinox
- Hundir Oliveri
- Hundir Shaws
Últimos Hundir Manuales
16 Octubre 2024
14 Octubre 2024
13 Octubre 2024
13 Octubre 2024
13 Octubre 2024
13 Octubre 2024
5 Octubre 2024
4 Octubre 2024
4 Octubre 2024
3 Octubre 2024