Champion CHSJ310 Manual de Usario

Champion Hierro CHSJ310

Lee a continuación 📖 el manual en español para Champion CHSJ310 (16 páginas) en la categoría Hierro. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/16
CHSJ310
USER MANUAL
EN - English
SE - Svenska
DK - Danske
NO - Norsk
FI - Suomi
Read this Manual carefully before use
IMPORTANT SAFETY INSTRUCTIONS
When using your at iron, basic safety precautions should always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USE
Use iron only for its intended use.
To protect against a risk of electric shock, do not immerse the iron in water or other liquids.
The iron should always be turned to “O” before plugging or unplugging from outlet. Never yank cord to disconnect from
outlet; instead, grasp plug and pull to disconnect.
Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely around iron
when storing.
Always disconnect iron from electrical outlet when lling it with water or emptying and when not in use.
Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of electric shock,
do not disassemble the iron, take it to a qualied service center for examination and repair. Incorrect reassembly can
cause a risk of electric shock when the iron is used.
Close supervision is necessary for any appliance being used by or near children. Do not leave iron unattended while
connected or on an ironing board.
Burns can occur from touching hot metal parts, hot water, or steam. Take caution when you turn a steam iron
upside down – there may be hot water in the reservoir.
If the malfunction indicator goes on, the at iron is not operating normally. Disconnect from the power supply and have
the at iron serviced by qualied service personnel.
Keep the iron and its cord out of reach of children less than 8 years of age when it is energized or cooling down.
When placing the iron on its stand, ensure that the surface on which the stand is placed is stable.
The iron must be used and rested on a stable surface.
SPECIAL INSTRUCTIONS
To avoid a circuit overload, do not operate another high wattage appliance on the same circuit.
If an extension cord is absolutely necessary, a 10-ampere cord should be used. Cords rated for less amperage may
overheat.
SAVE THESE INSTRUCTIONS
More specically:
DO NOT let children or untrained persons use the appliance without supervision.
NEVER immerse the iron, cable or plug in any liquid.
DO NOT leave the hot iron touching fabrics or very inammable surfaces.
DO NOT leave the appliance unnecessarily plugged in. Disconnect the plug from the mains when the appliance is not being used.
NEVER touch the appliance with wet or damp hands.
DO NOT use the power cord or the appliance in order to pull the plug out of the socket.
DO NOT leave the appliance exposed to the weather (rain, sun, etc.).
DO NOT leave the iron without supervision when it is connected to the power supply.
DO NOT ll the reservoir with water before removing the plug from the socket.
PLEASE NOTE!
Do not use chemical additive, scented substances or decalciers. Failure to comply with the above-mentioned regulations leads
to the loss of guarantee.
EN
DESCRIPTION OF DEVICE
(1). Nozzle
(3). Steam knob
(5). Spray button
(7). PCB button
(9). Cord
(11). Heel
(13). Water tank
(15). Display panel
(17). Self-clean button
(19). Bundle plate
(2). Inlet water cover
(4). Steam/Dry Iron switch
(6). Shot-steam button
(8). Top cover
(10). Cord bushing
(12). Heel root
(14). Isolating plate
(16). Ornament
(18). Soleplate
(20) Water cup
EN
ANTI-CALC SYSTEM
A special resin lter inside the water reservoir softens the water and prevents scale build-up in the plate. The resin lter is per-
manent and does not need replacing. Please note: Use tap water only. Distilled and/demineralized water makes the “Zero-Calc”
anti-calc system ineective by altering its physicochemical characteristics. Do not use chemical additives, scented substances or
decalciers. Failure to comply with the above-mentioned regulations leads to the loss of guarantee.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate fabrics. Always iron these fabrics at low temperatures.
The plate may cool down to the point where no more steam comes out, but rather drops of boiling water that can leave marks or
stains. In these cases, the Anti-drip system automatically activates to prevent vaporization, so that you can iron the most delicate
fabrics without risk of spoiling or staining them.
AUTOMATIC SHUT OFF
The automatic shut o device trips after the iron has been left for approx. 8 minutes in the upright position or unused for approx.
30 seconds in the horizontal position. The light comes on to indicate that shut o has tripped. As soon as you move the iron, the
device turns o and the iron starts working again.
GENERAL INSTRUCTIONS
When using the iron for the rst time, you may notice a slight emission of smoke and hear some sounds made by the expanding
plastics. This is quite normal and it stops after a short time. We also recommend passing the iron over an ordinary cloth before
using it for the rst time.
PREPARATIONS
Tvätten skall strykas i enlighet med de internationella symbolerna på plaggets etikett, eller om detta saknas , i
enlighet med typen av tyg.
Start ironing the garments requiring a low temperature. This reduces the waiting times (the iron takes less time to heat up than to
cool down) and eliminates the risk of scorching the fabrict.
STEAM IRONING
Filling the reservoir
1. Check that the plug is disconnected from the socket.
2. Move the steam selector (3) to “0” [Fig. 1].
3. Open the lid (2).
4. Raise the tip of the iron to help the water enter the opening without overowing.
5. Slowly pour the water into the reservoir using the special measure (18) and taking care not to go over the maximum level
indicated by “MAX” on the reservoir [Fig. 2].
6. Close the lid (2).
Selecting the temperature
1. Put the iron in a vertical position.
2. Put the plug in the socket.
3. Adjust the thermostat knob (14) according to the international symbol on the garment label [Fig. 3]. The plate temperature
pilot light (12) indicates that the iron is heating up. Wait until the plate temperature pilot light goes o before ironing.
Warning: during ironing, the plate temperature pilot light (12) comes on at intervals, indicating that the selected temperature is
maintained. If you lower the thermostat temperature after ironing at a high temperature, do not start ironing until the plate
temperature control light comes on again.
Selecting the steam
1. The quantity of steam is regulated by the steam selector (3).
2. Move the steam selector to a position between minimum and maximum depending on the quantity of steam required and
the temperature selected [Fig. 1].
Warning: The iron gives o steam continuously only if you hold the iron horizontally. You can stop the continuous steam by placing
the iron in a vertical position or by moving the steam selector to “0”. As indicated on the thermostat knob (14) and in the initial
table, you can only use steam at the highest temperatures. If the selected temperature is too low, water may drip onto the plate.
LABEL FABRIC TYPE THERMOSTAT
.Synthetic . Low temperature
.. Silk - wool .. Medium temperature
... Cotton - linen ... High temperature

Especificaciones del producto

Marca: Champion
Categoría: Hierro
Modelo: CHSJ310

¿Necesitas ayuda?

Si necesitas ayuda con Champion CHSJ310 haz una pregunta a continuación y otros usuarios te responderán




Hierro Champion Manuales

Hierro Manuales

Últimos Hierro Manuales