Chief SLM207 Manual de Usario

Chief Accesorio para proyector SLM207

Lee a continuación 📖 el manual en español para Chief SLM207 (1 páginas) en la categoría Accesorio para proyector. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8802-000273 Rev01

a Duchossois Group Company

05/09

SSB-207, SSM-207, SLB-207 and SLM-207 Interface Brackets

SSB-207, SSM-207, SLB-207 and SLM-207 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down on a flat surface.

3. Place the interface bracket onto the bottom of the projector and align the outside holes in the bracket with the threaded inserts in the bottom

of the projector.

4. Place a nylon spacer on the lamp door. Slide spacer between the projector and bracket so it lines up with the threaded insert of your

projector and the counter sink hole in the bracket.

5. Using the M4 x 10mm mounting screws with washers and one M4 x 20mm screw, position screws and washers into the mounting holes.

Tighten all fasteners at this time, securing the bracket to the projector.

NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in the

All-Points Security Kit.

(1) Interface Bracket (1) Spacer, Nylon, .500 x .194 x .500

(4) 10-24 Thumb Nuts ** (3) Washer, Flat, M4

(1) All-Points Security Kit (1) Screw, Flat head, M4 x 20mm

(3) Screw, Pan head, M4 x 10mm

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the

encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style

interface bracket installation.

SLB-207 SLM-207

Towards front of

projector

Towards front of

projector

(Note: SSB-style interface bracket connections

)

(Note: SSM-style interface bracket connections

circled)

Especificaciones del producto

Marca:	Chief
Categoría:	Accesorio para proyector
Modelo:	SLM207
Color del producto:	Wit
Peso.:	160 g
Ancho:	65 mm
Profundidad:	115 mm
Altura:	40 mm
Longitud del cable:	1.8 m
Peso del embalaje:	195 g
Ancho del embalaje:	100 mm
Empaquetadura en profundidad:	135 mm
Altura del embalaje:	45 mm
Fuente-de-alimentación:	Kabel
Código de seguridad internacional (IP):	IP68
Instrucciones:	Ja
factor vorm:	Ambidextrous
País de origen:	China
Material:	Silicone
Destinado a:	Kantoor
Certificados de sostenibilidad:	CE
Soporta Windows:	Ja
Número:	1
Temperatura de almacenamiento:	-25 - 80 °C
Funciones de seguridad:	Dustproof, Waterproof
Número de botones:	5
Conexión:	USB Type-A
Soporta el sistema operativo Mac:	Ja
Cumplimiento de la sostenibilidad:	Ja
Color de superficie:	Monochromatisch
Tipo de desplazamiento:	Knoppen
Altura del paquete principal (exterior):	300 mm
Ancho del embalaje principal (exterior):	265 mm
Peso bruto del embalaje principal (exterior):	10800 g
Longitud del paquete principal (exterior):	510 mm
Cantidad por caja principal (exterior):	50 stuk(s)
Temperatura de funcionamiento (TT):	-20 - 70 °C
Humedad relativa de funcionamiento (VV):	0 - 100 procent
Código del Sistema Armonizado (SA):	84716070