Chief SLM2220 Manual de Usario
Chief
Accesorio para proyector
SLM2220
Lee a continuación 📖 el manual en español para Chief SLM2220 (1 páginas) en la categoría Accesorio para proyector. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8850-000148 RevB
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets
SSB-2220, SSM-2220, SLB-2220 and SLM-2220 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information. Unpack carton and verify kit contents. If any listed parts are
missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
**Only used when installing SLB/SSB interface brackets. ****Used when mounting surface of projector is recessed.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the encircled
locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style interface bracket
installation.
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND DAMAGE
TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down.
3. Place interface bracket onto bottom of projector with three threaded inserts face up and two towards front of projector. Secure interface bracket to
projector using selected screw for model of projector (countersink screw or pan head screw).
4. Countersink screw in center countersink hole and pan head mounting screw in flush mounting hole. Your projector may require one or three
spacers for aligning bracket flat to projector. (Some models may suspend over bottom and have space between bracket and projector.)
Hitachi CP-X270W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .190 x 1/2" and 1/2" x .190 x 3/8" on top of each other and
centered over right threaded insert in front of projector. Using two 1/2" x .218 x 1/4" ,1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers, stack and
place them over three threaded inserts on left.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position and align interface bracket to projector using M4 x 30mm countersink screw in middle of bracket, M4 x 30mm Phillips pan head screw in
right of bracket, and M4 x 16mm Phillips pan head screw in left of bracket. Tighten all fasteners at this time, securing the bracket to the projector.
Hitachi CP-S307W, CP-X380W, CP-X385W
1. Place projector upside down on table with projector lens facing away. Stack 1/2" x .218 x 1/4" and 1/2" x .258 x 3/16" spacers on top of each other
centered over right threaded insert in front of projector. Using two 1/2" x .258 x 3/16" spacers, place one over middle threaded insert and one over
left threaded insert of projector.
2. Place interface bracket onto projector and align spacers and mounting holes.
3. Position and align interface bracket to projector using M4 x 16mm countersink screw in middle of bracket, M4 x 20mm Phillips pan head screw in
right hole of bracket and M4 x 16mm Phillips pan head screw in left hole of bracket. Tighten all fasteners at this time, securing the bracket to the
projector.
NOTE: Security Screws can be substituted when mounting interface bracket to projector by using the parts and installation instructions in
the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) 1/2" x .218" x 1/4" Round Spacer **** (1) Screw, Phillips Flat Head,
Machine, M4 x 16mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 30mm ****
(4) 10 - 24 Thumb
Nuts** (3) 1/2" x .194" x 1/2" Round Spacer **** (1) Screw, Phillips Pan Head,
Machine, M4 x 16mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(1) All-Points Security
Kit (3) 1/2" x .194" x 3/8" Nylon Spacer **** (1) Screw, Phillips Flat Head Machine,
M4 x 25mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
(2) Washer, Flat, M4 (1) Screw, Phillips Pan Head, Machine,
M4 x 8mm **** (1) Screw, Phillips Pan Head,
Machine, M4 x 20mm **** (3) 1/2" x .257" x 3/16" Round
Spacer ****
SLB-2220 SLM-2220
Towards front of
projector
Towards front of
projector
(
N
ote: SSB-style interface bracket connections
a
r
e
e
n
c
ir
c
l
e
d
)
(Note: SSM-style interface bracket connection
s
a
re encircled)
Especificaciones del producto
| Marca: | Chief |
| Categoría: | Accesorio para proyector |
| Modelo: | SLM2220 |
¿Necesitas ayuda?
Si necesitas ayuda con Chief SLM2220 haz una pregunta a continuación y otros usuarios te responderán
Accesorio para proyector Chief Manuales
12 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
2 Septiembre 2024
Accesorio para proyector Manuales
- Accesorio para proyector Sony
- Accesorio para proyector Casio
- Accesorio para proyector Panasonic
- Accesorio para proyector BenQ
- Accesorio para proyector Optoma
- Accesorio para proyector Vision
- Accesorio para proyector Sanyo
- Accesorio para proyector Nec
- Accesorio para proyector Da-Lite
- Accesorio para proyector AV:link
- Accesorio para proyector Barco
- Accesorio para proyector Vogels
- Accesorio para proyector InFocus
- Accesorio para proyector Auna
- Accesorio para proyector Viewsonic
- Accesorio para proyector Newstar
- Accesorio para proyector Projecta
- Accesorio para proyector Peerless
- Accesorio para proyector Chipolino
- Accesorio para proyector Gabor
- Accesorio para proyector Konig & Meyer
- Accesorio para proyector Speaka
- Accesorio para proyector Tempest
- Accesorio para proyector Gravity
- Accesorio para proyector Kanto
- Accesorio para proyector V7
- Accesorio para proyector Unicol
- Accesorio para proyector Roadinger
- Accesorio para proyector My Wall
- Accesorio para proyector Smart Media
Últimos Accesorio para proyector Manuales
18 Octubre 2024
27 Septiembre 2024
22 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024