Chief SSB3131 Manual de Usario

Chief Accesorio para proyector SSB3131

Lee a continuación 📖 el manual en español para Chief SSB3131 (1 páginas) en la categoría Accesorio para proyector. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

I N S T A L L A T I O N I N S T R U C T I O N S

Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes

no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use

of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or

implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief Manufacturing, a products division of Milestone AV Technologies

8401 Eagle Creek Parkway, Savage, MN 55378

• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918

8850-000140 Rev01

a Duchossois Group Company

05/09

SSB-180, SSM-180, SLB-180 and SLM-180 Interface Brackets

SSB-180, SSM-180, SLB-180 and SLM-180 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific

installation instructions provided with the mount for additional installation information.

Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.

WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!

Installation Instructions

WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND

DAMAGE TO EQUIPMENT! DO NOT over tighten screws when installing interface bracket.

NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.

1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.

2. Turn projector upside down.

3. Remove the two rear feet of the projector.

4. Place the interface bracket onto the bottom of the projector and align the three mounting holes in the bracket with the three thread inserts

in the bottom of the projector.

5. Using M4 x 6mm and M4 x 8mm screws with M4 flat washers, secure interface bracket to projector and tighten all fasteners at this time.

NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation

instructions in the All-Points Security Kit.

(1) Interface Bracket (3) M4 Flat washer

(3) 10 - 24 Thumb Nuts** (1) M4 -6mm Phillips Pan Screws

(1) All-Points Security Kit (2) M4 -8mm Phillips Pan Screws

**Only used when installing SLB/SSB interface brackets.

NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the

encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style

interface bracket installation.

(

)

(Note: SS

)

SLM-180

SLB-180

Towards front of

projector

Towards front of

projector

Especificaciones del producto

Marca:	Chief
Categoría:	Accesorio para proyector
Modelo:	SSB3131
Color del producto:	Black, Orange
Peso.:	3600 g
Número de velocidades:	6
Fuente-de-alimentación:	AC
Potencia de entrada:	1010 W
Velocidad ajustable:	Ja
tipo de lijadora:	Schuurmachine
voltaje-de-entrada-de-CA:	127 V
Frecuencia-de-entrada-de-CA:	60 Hz
Velocidad de ralentí de los neumáticos (min):	210 m/min
Neumático de ralentí (máx.):	450 m/min
Amperaje:	8 A