Chief SSM002 Manual de Usario

Lee a continuación 📖 el manual en español para Chief SSM002 (1 páginas) en la categoría Accesorio para proyector. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 F:877.894.6918 / 952.894.6918
8850-000002 RevB
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-002, SSM-002, SLB-002 and SLM-002 Interface Brackets
SSB-002, SSM-002, SLB-002 and SLM-002 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB Interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place the interface bracket onto the bottom of the projector and align the holes in the bracket with the threaded inserts in the bottom of the
projector.
4. Using the 8-32 x 1/2" mounting screws and #8 external lock washers, secure interface bracket to projector and tighten all fasteners at this
time.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (4) LOCKWASHER, #8, External
(6) 10-24 Thumb Nuts ** Quantity of (4) for SSB
brackets
(4) SCREW, Phillips Pan Head, 8-32 x 1/2"
(1) All-Points Security Kit
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-002 SLM-002
Towards front of
projector
Towards front of
projector
(Note: SSM-style interface bracket connection
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(Note: SSB-style interface bracket connections
a
e
e
c
i
r
c
l
e
d
)

Especificaciones del producto

Marca: Chief
Categoría: Accesorio para proyector
Modelo: SSM002

¿Necesitas ayuda?

Si necesitas ayuda con Chief SSM002 haz una pregunta a continuación y otros usuarios te responderán




Accesorio para proyector Chief Manuales

Accesorio para proyector Manuales

Últimos Accesorio para proyector Manuales