Chord CPA 2500 Manual de Usario

Chord receptor CPA 2500

Lee a continuación 📖 el manual en español para Chord CPA 2500 (12 páginas) en la categoría receptor. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

welcome

Thank you for buying a Chord product.

Before you start to enjoy using to your Chord product, please take a couple of minutes to read how to connect your audio

equipment and loudspeakers to your pre-amplifier or integrated amplifier and how to maximise your listening experience.

user guide for CPA 2500 pre-amplifier

The pre-amplifier is the control centre of your system. By connecting your audio sources to it you can choose the source you

want at any particular time and control it.

You can also adjust the balance and volume before the signal is sent to a power amplifier. Your pre-amplifier can be

operated manually or via the Chord remote control.

background

We want you to be confident using your new Chord amplifier.

You’re probably an audiophile with extensive knowledge of audio equipment. However, you may not be!

So in the following section we explain a few basics to help you get started, or get you back up to speed if you’re a little rusty.

connecting your equipment

Chord amplifiers are supplied with and designed to be connected using balanced inputs. The interconnecting cables you use will

depend on the available input and output sockets on your other equipment. We have installed unbalanced inputs on all Chord

equipment, thus enabling you to mix Chord and other manufacturer’s equipment. Whichever cable you choose it is important

to make sure it is fully screened to avoid any noise problems.

Balanced inputs carry twice the strength of signal of unbalanced inputs and are able to be fed down long lengths

of cable with less deterioration of signal. They are also less prone to interference than unbalanced inputs.

Balanced inputs have three pins and use Neutric XLR style connectors. Pin 1 is earth, pin 2 is positive and pin 3

is negative.

Unbalanced inputs use RCA phono connectors which are gold plated with teflon high performance

dielectric insulators for optimum performance.

Speakers

Power Amplifier

or integrated

amplifier

Pre-amplifier

Audio Source

when setting up

To ensure that your Chord integrated amplifier works efficiently and safely, please pay particular attention to the following

issues.

ventilation

Your Chord integrated amplifier should have at least 5cm of clear space all around it to ensure a free flow of air at all times.

When driven continuously at well above average levels, the temperature at the back of the unit may exceed 50ºC. This is

normal and no cause for concern, although it does highlight the need for adequate ventilation around the unit. We recommend

that you do not place your integrated amplifier directly on a carpet.

mains lead and plug

All Chord equipment comes supplied with the correct mains lead and plug. This should be used at all times.

if you need to fit a plug for UK/Europe

Connect the blue wire to the neutral terminal Connect the

brown wire to the live terminal Connect the yellow/green

wire to the earth terminal

if you need to fit a plug for US/Canada

Connect the white wire to the neutral terminal

Connect the black wire to the live terminal Connect

the green to the earth terminal

earthing issues in Europe

In some European countries a hum may occur if your integrated/pre-amplifier is connected to mains sockets that do not have an

earth. If this is the case please ensure that:

1. Your integrated/pre-amplifier is connected via a multi-way mains block which contains an earth point at each socket outlet.

This is to ensure that the chassis metalwork of each item is connected together.

2. Use the connecting points on your Chord unit and connect to an available earth point.

3. We recommend that an earthing method for your building is implemented.

safety warnings

It is important that your integrated/pre-amplifier is earthed at all times via its own mains lead. Failure to do this may be

hazardous. The power supply components within the amplifier are designed to be operated at lethal voltages and energy levels.

Circuit designs that embody these components conform with applicable safety requirements. Precautions must be taken to

prevent accidental contact with power-line potentials. Do not connect grounded test equipment.

These units comply with EN 50081-1 and IEC 801/2

Especificaciones del producto

Marca:	Chord
Categoría:	receptor
Modelo:	CPA 2500
Colocación del dispositivo:	Ingebouwd
Color del producto:	Zwart
Ancho:	592 mm
Profundidad:	522 mm
Altura:	45 mm
Tipo de material (arriba):	Glas
Número de quemadores/zonas de cocción:	4 zone(s)
tipo de placa:	Keramisch
Ancho de la placa:	59.2 cm