Chord DI-P1 Manual de Usario

Chord sistema de alta fidelidad DI-P1

Lee a continuación 📖 el manual en español para Chord DI-P1 (2 páginas) en la categoría sistema de alta fidelidad. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
DI P1-
Passive Direct Injection Box
Item ref: 173 92.2 UK
User Manual
Introduction
Thank you for choosing the Chord DI-P1 passive D.I. box as part of your audio signal chain. The DI-P1 converts high impedance audio from
instruments or line outputs to w impedance balanced output to be fed directly into a mixing console or amplifier input. Low impedance (Lo-Z) is a lo
capable of longer cable runs via XLR connection with lower signal degradation than high impedance.
Input panel Output panel
INPUT: 6. Hi- put : - OAT-LIFT switch 3mm Z in GND GND FL
PAD: Attenuation switch
THRU Hi-Z out LOW- OUT 600 : Balanced XLR output : 6.3mm Z Ω
Operation
Connect the instrument ( other high impedance audio source) to the DI-P1 via the 6.3mm INPUT jack. or
To feed backline amplifier or further high impedance input, use the adjacent 6.3mm THRU jack. to a
Connect the L -Z OUT connection directly to the mixing console or amplifier input using balanced XLR leads. OW
High level input signals can be attenuated so as not to overdrive the mixer or amp inputs by using the PAD switch.
0dB setting leaves the input unaffected, whereas -20dB and -40dB settings reduce the signal level progressively.
The DI-P1 has an inbuilt noise filter to help eliminate RF and mains hum. In some ses, it is necessary to isolate the signal ground to help reduce ca
such noise and the GND switch has 3 options to help with this. GND setting is fully grounded, FLOAT setting isolates the signal ground from the case
but retains the noise filter and LIFT setting isolates the signal ground altogether without the filter.
In the event of noise appearing in the signal chain, try these settings to see if FLOAT or LIFT can improve the signal quality.
Specifications
Errors and omissions excepted.
Copyright© 2019. AVSL Group Ltd.
Input
6.3mm jack (unbalanced)
Outputs
XLRM (balanced), 6.3mm k through (unbal) jac
Input impedance
>100k Ohms
Output impedance
600 Ohms
Controls
0/-20/-40dBu pad & Ground-Float-Lift switch
Dimensions
86 x 70 x 45mm
Weight
234g
Disposal: ol on the The “Crossed Wheelie Bin” symb
product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other
household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local
council guidelines.

Especificaciones del producto

Marca: Chord
Categoría: sistema de alta fidelidad
Modelo: DI-P1

¿Necesitas ayuda?

Si necesitas ayuda con Chord DI-P1 haz una pregunta a continuación y otros usuarios te responderán


sistema de alta fidelidad Chord Manuales

Chord

Chord DI-P1 Manual de Usario

27 Julio 2024

sistema de alta fidelidad Manuales

Últimos sistema de alta fidelidad Manuales

Morel

Morel MXT280C Manual de Usario

27 Octubre 2024
Rotel

Rotel RSP-975 Manual de Usario

27 Octubre 2024
Motu

Motu Audio Express Manual de Usario

27 Octubre 2024
Rockford Fosgate

Rockford Fosgate HD9813SGU-STAGE2 Manual de Usario

26 Octubre 2024
Thomson

Thomson MIC123BT Manual de Usario

26 Octubre 2024
Samsung

Samsung MAX-KC930 Manual de Usario

25 Octubre 2024
Samsung

Samsung MM-ZL7 Manual de Usario

25 Octubre 2024
Philips

Philips FWM996X Manual de Usario

24 Octubre 2024
Sony

Sony MHC-RV333D Manual de Usario

21 Octubre 2024
Sony

Sony MHC-FR10 Manual de Usario

20 Octubre 2024