Cisco Aironet 1142N Manual de Usario

Cisco punto de acceso Aironet 1142N

Lee a continuación 📖 el manual en español para Cisco Aironet 1142N (36 páginas) en la categoría punto de acceso. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/36
GETTING S GTARTED UIDE
Cisco Aironet 1140 Series Autonomous Access Point
1About this Guide
2Safety Instructions
3Overview
4Obtaining and Assigning an IP Address
5Mounting the Access Point
6Configuring Basic Settings
7Troubleshooting
8Access Point Specifications
9Obtaining Documentation and Submitting a Service Request
10 Declarations of Conformity and Regulatory Information
2
78-18997-01
1 About this Guide
This Guide explains how to install and configure your Cisco Aironet 1140 Series Autonomous Access
Point. This guide also provides mounting instructions and limited troubleshooting procedures.
2 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings
document that is shipped with your access point. The translated warnings are also in the Translated
Safety Warnings for Cisco Aironet Access Points, which is available on your documentation CD and
cisco.com.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury.
Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the
statement number provided at the end of each warning to locate its translation in the
translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Read the installation instructions before you connect the system to its power source.
Statement 1004
Warning
This product must be connected to a Power-over-Ethernet (PoE) IEEE 802.3af compliant
power source or an IEC60950 compliant limited power source.
Statement 353
Warning
This equipment must be externally grounded using a customer-supplied ground wire
before power is applied. Contact the appropriate electrical inspection authority or an
electrician if you are uncertain that suitable grounding is available.
Statement 366
3
Warning
Installation of the equipment must comply with local and national electrical codes.
Statement 1074
Warning
This product relies on the buildings installation for short-circuit (overcurrent)
protection. Ensure that the protective device is rated not greater than:
20A.
Statement 1005
Warning
Do not operate your wireless network device near unshielded blasting caps or in an
explosive environment unless the device has been modified to be especially qualified for
such use.
Statement 245B
Warning
In order to comply with FCC radio frequency (RF) exposure limits, antennas should be
located at a minimum of 7.9 inches (20 cm) or more from the body of all persons.
Statement 332
Caution When mounting the access point to a wall or ceiling, be sure to use appropriate fasteners.
The fasteners used must be capable of maintaining a minimum pullout force of 20 lbs (9
kg) and must use all 4 indented holes on the low-profile mounting bracket.
Caution This product and all interconnected equipment must be installed indoors within the same
building, including the associated LAN connections as defined by Environment A of the
IEEE 802.af Standard.
Note The access point is suitable for use in environmental air space in accordance with section
300.22.C of the National Electrical Code and sections 2-128, 12-010(3), and 12-100 of the
Canadian Electrical Code, Part 1, C22.1. You should not install the power supply or power
injector in air handling spaces.
Note Use only with listed ITE equipment.

Especificaciones del producto

Marca: Cisco
Categoría: punto de acceso
Modelo: Aironet 1142N

¿Necesitas ayuda?

Si necesitas ayuda con Cisco Aironet 1142N haz una pregunta a continuación y otros usuarios te responderán




punto de acceso Cisco Manuales

punto de acceso Manuales

Últimos punto de acceso Manuales