Cisco Aironet 2602E Manual de Usario
Cisco
Access point
Aironet 2602E
Lee a continuación 📖 el manual en español para Cisco Aironet 2602E (40 páginas) en la categoría Access point. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/40
G ETTING S GTARTED UIDE
Cisco Aironet 2600 Series Access Points
July, 2012
P/N: 78-20842-01
1About this Guide
2Introduction to the Access Point
3Safety Instructions
4Unpacking
5Configurations
6Access Point Ports and Connectors
7Configuring the Access Point
8Mounting the Access Point
9Deploying the Access Point on the Wireless Network
10 Troubleshooting
11 Declarations of Conformity and Regulatory Information
12 Configuring DHCP Option 43 and DHCP Option 60
13 Access Point Specifications
2
1 About this Guide
This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series
Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point in this
document.
2 Introduction to the Access Point
The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream
rates over a deployable distance with high reliability when serving clients. The 2600 series provides
high reliability and overall wireless performance.
The 2600 series offers dual-band radios (2.4 GHz and 5 GHz) with integrated and external antenna
options. The access points support full inter-operability with leading 802.11n clients, and support a
mixed deployment with other access points and controllers.
The 2600 series access point is available in both controller-based (Unified) and standalone
(Autonomous) configurations and supports:
•Simultaneous single-band or dual-band (2.4 GHz/5 GHz) radios
•Integrated antennas on 2602I access point models (AIR-CAP2602I-x-K9)
•External antennas for rugged 2602E access point models (AIR-CAP2602E-x-K9)
Note The ‘x’ in the model numbers represents the regulatory domain. Refer to “Regulatory
Domains” section on page 6 for a list of supported regulatory domains.
The features of the 2600 series are:
•Processing sub-systems (including CPUs and memory) and radio hardware which supports:
–
Network management
–
CleanAir—Automatic detection, classification, location and mitigation of RF interference
(not available on autonomous or standalone models)
–
ClientLink 2.0—BeamForming to 802.11n clients as well as legacy 802.11a/g OFDM clients
–
VideoStream
–
Location
–
WIDS/WIPS
–
Security
–
Radio Resource Management (RRM)
–
Rogue detection
3
–
Management Frame Protection (MFP)
–
Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps
data-rates
•32 MB flash size
•802.11af/at
–
CDP (Cisco Discovery Protocol)
•2.4 GHz and 5 GHz 802.11n radios with the following features:
–
3TX x 4RX
–
3-spatial streams, 450 Mbps PHY rate
–
Spectrum intelligence
–
DPD (Digital Pre-Distortion) technology
–
Cisco Vector Beamforming—Implicit Co-phase beamforming for .11ag clients and 1
spatial-stream and 2 spatial-stream clients
–
Radio hardware is capable of explicit compressed beamforming (ECBF) per 802.11n standard
3 Safety Instructions
Translated versions of the following safety warnings are provided in the translated safety warnings
document that is shipped with your access point. The translated warnings are also in the Translated
Safety Warnings for Cisco Aironet Access Points, which is available on Cisco.com.
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that could cause bodily injury.
Before you work on any equipment, be aware of the hazards involved with electrical
circuitry and be familiar with standard practices for preventing accidents. Use the
statement number provided at the end of each warning to locate its translation in the
translated safety warnings that accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
Read the installation instructions before you connect the system to its power source.
Statement 1004
Especificaciones del producto
Marca: | Cisco |
Categoría: | Access point |
Modelo: | Aironet 2602E |
¿Necesitas ayuda?
Si necesitas ayuda con Cisco Aironet 2602E haz una pregunta a continuación y otros usuarios te responderán
Access point Cisco Manuales
15 Agosto 2024
9 Agosto 2024
5 Agosto 2024
4 Agosto 2024
31 Julio 2024
31 Julio 2024
28 Julio 2024
26 Julio 2024
24 Julio 2024
22 Julio 2024
Access point Manuales
- Access point HP
- Access point Allied Telesis
- Access point Airlive
- Access point Edimax
- Access point Asus
- Access point Sitecom
- Access point TP Link
- Access point Fortinet
- Access point DataVideo
- Access point Totolink
- Access point Engenius
- Access point Netis
- Access point Draytek
- Access point Devolo
- Access point Linksys
- Access point Buffalo
- Access point Netgear
- Access point LevelOne
- Access point Dell
- Access point Planet
- Access point Zebra
- Access point D-Link
- Access point Aruba
- Access point Tenda
- Access point Ubiquiti Networks
- Access point Trendnet
- Access point Mikrotik
- Access point EQ3
- Access point Homematic IP
- Access point Hawking Technologies
- Access point LigoWave
- Access point StarTech.com
- Access point Intellinet
- Access point SMC
- Access point Cambium Networks
- Access point AMX
- Access point Mach Power
- Access point Comtrend
- Access point Extreme Networks
- Access point Atlantis Land
Últimos Access point Manuales
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
14 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024