Clas Ohlson ML520-11 Manual de Usario
Clas Ohlson
Snijmachine
ML520-11
Lee a continuación 📖 el manual en español para Clas Ohlson ML520-11 (12 páginas) en la categoría Snijmachine. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/12
EnglishSvenskaNorskSuomiDeut s ch
Art.no Model
30-9376 ML520-11 Ver. 20140505
Tile Cutter
Kakelskärare
Flisekutter
Laattaleikkuri
Fliesenschneider
2
English
Adjustable guide.
Cutting angle 0–60 degrees.
Tile Cutter
Art. no 30-9376
Please read the entire instruction manual before using and save it for future use.
We apologise for any text or photo errors and any changes of technical data.
If you have any questions concerning technical problems please contact our
Customer Service Department (see address on reverse.)
Presentation
• A tile cutter for professionals. It cuts and snaps in two simple steps.
• Magnesium alloy base plate with hardened metal scoring wheel.
Can produce square or angled cuts (0–60°).
• Max. cutting length 500 mm, max. tile thickness 16 mm.
3
English
Straight Cuts
Set the position of the cut with the guide.
Hold the tile firmly with one hand, and with
the other apply an even and moderate
pressure down on the handle while running
the scoring wheel across the glazed surface.
The scoring wheel should just cut the glaze.
Once the glaze has been scored it is time to
snap the tile. Place the tile, glazed surface
up, on the base plate. Position the score
just under the base plate’s centre line.
Rest the breaker-bar on the tile and close to
the guide and make sure that the breaker-bar
ends are equidistant from the score.
Gently apply pressure to the handle. Do not
use more force than necessary to snap the tile
along the score!
Important!
Make sure that the scoring wheel
does not touch the base plate when snapping
the tile. If you press too hard on the handle
while snapping the tile, the tile may break
unevenly and possibly crack into several pieces.
Angled Cuts
Angled cuts are carried out in generally in
the same way as straight cuts. The only
difference is that you must set the desired
angle before scoring the tile. Use the guide
ruler and fence. Loosen the wing nut,
adjust the angle and tighten the wing nut
again before scoring.
Important! Once again, make sure that
the scoring wheel does not touch the base
plate when snapping the tile.
Replacement of Scoring Wheel
Replacing the scoring wheel requires a posidrive,
screwdriver and a 10 mm spanner to loosen
the bolt and nut which hold the scoring wheel
in place.
Especificaciones del producto
| Marca: | Clas Ohlson |
| Categoría: | Snijmachine |
| Modelo: | ML520-11 |
¿Necesitas ayuda?
Si necesitas ayuda con Clas Ohlson ML520-11 haz una pregunta a continuación y otros usuarios te responderán
Snijmachine Clas Ohlson Manuales
14 Agosto 2024
Snijmachine Manuales
- Snijmachine Electrolux
- Snijmachine Bosch
- Snijmachine Ade
- Snijmachine Ariete
- Snijmachine Bartscher
- Snijmachine Orbegozo
- Snijmachine Fagor
- Snijmachine Gorenje
- Snijmachine Silvercrest
- Snijmachine Makita
- Snijmachine Domo
- Snijmachine Trisa
- Snijmachine Skil
- Snijmachine Fritel
- Snijmachine Cuisinart
- Snijmachine Dremel
- Snijmachine Trebs
- Snijmachine Mach
- Snijmachine H.Koenig
- Snijmachine Zelmer
- Snijmachine Powerplus
- Snijmachine Graef
- Snijmachine Sammic
- Snijmachine Bifinett
- Snijmachine Gastroback
- Snijmachine Powerfix
- Snijmachine Team
- Snijmachine CaterChef
- Snijmachine Efbe-schott
- Snijmachine Gourmetmaxx
- Snijmachine Ritter
- Snijmachine Domoclip
- Snijmachine Baker's Mark
- Snijmachine Avantco
- Snijmachine Kogan
- Snijmachine Wolfcraft
- Snijmachine Esperanza
- Snijmachine Berkel
- Snijmachine Louis Tellier
- Snijmachine Pro-Cut
- Snijmachine Jokari
- Snijmachine Prince Castle
- Snijmachine Weston
Últimos Snijmachine Manuales
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
17 Septiembre 2024
14 Septiembre 2024