Concept2 Model D Manual de Usario

Lee a continuación 📖 el manual en español para Concept2 Model D (41 páginas) en la categoría bicicleta estática. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/41
2
ON A REGULAR BASIS
Firmware is the internal software that runs your Performance Monitor.
Your PM comes preinstalled with the latest firmware, however, new and
improved versions are offered regularly. We offer free software called
the Concept2 Utility that makes it easy to update your PM with the
latest firmware version at any time. Visit concept2.com/pm5firmware for
more information.
DAILY
Wipe stainless monorail top with a cloth or non-abrasive scouring pad
after use with a household all-purpose cleaner. Do not use bleach
products, mineral acids or coarse abrasives.
EVERY 50 HOURS OF USE (Weekly for Institutional Users):
Lubricate the chain with a teaspoon of purified mineral oil, 3-IN-ONE®
oil, or 20W motor oil. Apply oil to a paper towel, and rub the paper towel
along entire length of chain. Wipe off the excess. Repeat if needed. Do
not clean the chain with any kind of cleaner or solvent, e.g. WD-40®.
Use of this machine with a worn or weakened part, such as the chain,
sprockets, chain/swivel connector, handle U-bolt or shock cord, may
result in injury to the user. When in doubt about the condition of any
part, Concept2 strongly advises that it be replaced immediately. Use only
genuine Concept2 parts. Use of other parts may result in injury or poor
performance of machine.
The machine should be used on a stable, level surface.
The machine should NOT be bolted or permanently fixed to the floor.
Doing so may result in permanent damage to the frame.
Keep children, pets, fingers and clothing away from seat rollers. Seat
rollers can cause injury.
Perform proper maintenance as described in the Maintenance section of
this manual.
Pull straight back with both hands. Do not row with one hand only. Abuse
of the chain can result in injury.
Never twist chain or pull from side to side.
Place handle against the chain guide or in handle hooks before letting go.
Do not let handle fly into chain guide.
ALWAYS PUT THE FRAMELOCK IN THE LOCKED POSITION WHEN
THE FLYWHEEL AND MONORAIL SECTIONS ARE CONNECTED AND
BEFORE MOVING THE ROWERG. FAILURE TO DO SO MAY RESULT
IN INJURY IF THE UNIT IS LIFTED OR MOVED.
To avoid possible injury, use caution while attaching the monorail
section to the flywheel section and while operating the framelock.
DO NOT stand the RowErg up on end as it may tip over.
IMPORTANT USE AND SAFETY NOTES
EVERY 250 HOURS OF USE (Monthly for institutional users):
1. Inspect chain for stiff links. If thorough lubrication does not help, the
chain should be replaced.
2. Inspect chain-handle connection for wear. If the hole has become
elongated, or the U-bolt is worn halfway through, replace the entire
connection.
3. Tighten the shock cord if the handle does not return all the way to
the fan enclosure.
4. Check screws for tightness, including those used for assembly.
5. Loosen or tighten the nuts on the Performance Monitor arm joints
as necessary.
6. Check for dust inside flywheel with a flashlight. Vacuum if needed.
For complete maintenance information and instructions visit
concept2.com/service.
ENGLISH
WARNING! The safety level of the machine can be
maintained only if it is examined regularly for damage and wear.
Replace defective components immediately to ensure safety and
performance or keep machine out of use until repair.
RECOMMENDED MAINTENANCE
SCHEDULE

Especificaciones del producto

Marca: Concept2
Categoría: bicicleta estática
Modelo: Model D

¿Necesitas ayuda?

Si necesitas ayuda con Concept2 Model D haz una pregunta a continuación y otros usuarios te responderán




bicicleta estática Concept2 Manuales

bicicleta estática Manuales

Últimos bicicleta estática Manuales