Crestron C2N-RTHS Manual de Usario

Crestron humidificador C2N-RTHS

Lee a continuación 📖 el manual en español para Crestron C2N-RTHS (2 páginas) en la categoría humidificador. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

C2N-RTHS

Temperature and Humidity Sensor

Installation Guide

Wiring

Make the necessary connections as called out in the illustration. Apply power after all

connections have been made.

CAUTION: Insufcient power can lead to unpredictable results or damage to the

equipment. Use the Crestron Power Calculator to help calculate how much power is

needed for the system (www.crestron.com/calculators).

NOTE: When wiring the Cresnet network, consider the following:

• Use Crestron Certied Wire.

• Use Crestron power supplies for Crestron equipment.

• Provide sufcient power to the system.

Wiring the C2N-RTHS

Description

The Crestron®

C2N-RTHS is a wall-mounted temperature and relative humidity sensor that

communicates directly with any Crestron control system via the Cresnet

® control network.

One-piece mounting makes the C2N-RTHS simple to install. The 1-1/2 in (38.1 mm)

diameter face protrudes just 1/8 in (3.2 mm) from the wall surface and is easily painted or

wallpapered to blend into the wall surface.

C2N-RTHS Specications

Installation

NOTES: Ensure the installation location is not close to a heat or humidity source and is

away from direct sunlight, skylights, and windows. When mounting the sensor outdoors,

do not place in direct sunlight, and do not place where the sensor will be directly

exposed to precipitation. Sensors are suitable for mounting in dry or damp locations as

dened by the National Electrical Code.

• Install and use this product in accordance with appropriate electrical codes and

regulations.

• A licensed electrician should install this product.

• Mount sensors on a vibration-free surface.

NOTE: Before using the C2N-RTHS, ensure the device is using the latest rmware.

Check for the latest rmware for the C2N-RTHS at www.crestron.com/rmware. Load

the rmware onto the device using Crestron Toolbox™ software.

Complete the following procedure to install the C2N-RTHS:

1. Locate an area on the wall that is free of miscellaneous wiring and studs.

2. Make a small hole near the center of the designated mounting site to verify that the

location is suitable.

3. Drill or cut a 1 in (26 mm) diameter circular hole in the wall at the desired position.

4. Route the Cresnet wires to the sensor. Use the four wire nuts included to connect

the wires (red to red, white to white, blue to blue, and black to black).

Cresnet Wiring for the C2N-RTHS

Additional Resources

Visit the product page on the Crestron website (www.crestron.com)

for additional information and the latest rmware updates. Use a QR

reader application on your mobile device to scan the QR image.

Black Ground

Red 24 V

White Y

Blue Z

Wire nuts

Cresnet

wires

Pigtail wires

from sensor

Mounting clips

1 in (26 mm) hole

C2N-RTHS Front and Angled View

NOTE: The miniature setup button and red LED are used for setting the network ID

for the initial conguration or when the device is being added or replaced. They are

also used for touch-settable ID (TSID).

Mounting clips

Setup

button

Red

LED

C2N-RTHS Rear and Angled Views

10 in

(254 mm)

5. Press t the sensor into the hole; the clips on either side of the sensor hold it in

place.

NOTE: The face of the sensor may be painted or wallpapered to match the wall.

Ensure that paint does not enter (or that wallpaper does not cover) the perimeter

gap or the holes for the setup button and LED.

SPECIFICATION DETAILS

Measuring Range

Temperature -40º to 176 ºF (-40º to 80 ºC)

Humidity 0% to 100% RH

Output Resolution 0.1 ºF (0.1 ºC); 1% RH

Accuracy ±1.0 ºF (0.5 ºC); 5% RH

Temperature Accuracy

Over Full Range ±0.9 °F (0.5 °C)

At Room Temperature +0.2/-0.7 °F (+0.1/-0.4 °C)

Humidity Accuracy ±5%

Connection ~10 in (~25 cm) 4-wire pigtail;

Connects to Cresnet control network

Power Requirements

Cresnet Power Usage 0.25 W (0.01 Amps @ 24 Vdc)

As of the date of manufacture, the device has been tested and found to comply with specications for

CE marking.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions:(1) This device may not cause harmful interference and (2) this device must accept any

interference received, including interference that may cause undesired operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for

compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada

The product warranty can be found at www.crestron.com/warranty.

The specic patents that cover Crestron products are listed at patents.crestron.com.

Certain Crestron products contain open source software. For specic information, please visit

www.crestron.com/opensource.

Crestron, the Crestron logo, Cresnet, and Crestron Toolbox are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks,

registered trademarks, and trade names may be used in this document to refer to either the entities

claiming the marks and names or their products. Crestron disclaims any proprietary interest in the

marks and names of others. Crestron is not responsible for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

Crestron Electronics, Inc. Installation Guide - DOC. 6232C

15 Volvo Drive Rockleigh, NJ 07647 (2009412)

Tel: 888.CRESTRON 10.16

Fax: 201.767.7576 Specications subject to

www.crestron.com change without notice.

Troubleshooting

The following table provides corrective actions for possible trouble situations. If further

assistance is required, please contact a Crestron customer service representative.

C2N-RTHS Troubleshooting

TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION

There is no temperature

or humidity reading.

The wiring is not

properly connected.

Check the connection;

refer to the “Wiring”

section.

The Cresnet ID is

incorrect.

Check the Cresnet ID.

The programming is

incorrect.

Check the SIMPL

Windows program.

Especificaciones del producto

Marca:	Crestron
Categoría:	humidificador
Modelo:	C2N-RTHS
Color del producto:	Black, Red
Ancho:	169 mm
Profundidad:	7.8 mm
Altura:	265 mm
Manual de usuario:	Ja
Color:	Nee
Edad recomendada (máx.):	99 jaar
Edad recomendada (mín.):	3 jaar
Mostrar.:	LCD
Diagonal de la pantalla:	10 "
Resolución:	- lpi
Tecnología de conectividad:	Bedraad
Género propuesto:	Jongen/meisje
Incluye ratón:	Nee
Incluye bolígrafo:	Ja
Tipo-producto:	Magnetisch takenbord voor kinderen
Tipo de Batería:	CR2020
Área de trabajo:	- mm
Altura máxima de lectura:	- mm
bolígrafo inalámbrico:	Ja
Pluma de precisión:	- mm
Peso de la tableta:	157 g