CRUX RVCCH-75DC Manual de Usario
CRUX
cámara de marcha atrás
RVCCH-75DC
Lee a continuación 📖 el manual en español para CRUX RVCCH-75DC (6 páginas) en la categoría cámara de marcha atrás. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/6
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
1 of 3
• Adds reverse camera input to the Uconnect Touchscreen Radio
• Aermarket tailgate handle camera included
• Automacally switches to Rear-view when car is in Reverse mode
• Plug & Play Installaon
PRODUCT FEATURES:
PARTS INCLUDED:
RVCCH-75DC Module RVCCH-75DC Harness CDR-02 Camera
INSTALLATION DIAGRAM:
WHITE Wire
Parking Guideline
To Radio
OEM Radio
Harness
DP
ON
DIP
SWITCH
LED*
*LED RED = Power ON Status
LED BLUE = Data Bus ON Status
RVC Video
Signal Input
RED Wire Push in Connectors
all the way
Line up Arrows
Regulator
20 Ft. Coax Cable
RED Wire
Tape O
(Not Used)
BLACK
Wire
BLACK
(Ground)
8-Pin Molex Represents Solder Joint
Connect RCAs and secure
with tape all around
WHITE Wire
(Camera Power Output
+12V 250mA)
OR*
*Connect BLACK (ground) wire to chassis ground.
If video noise is present, we recommend connecting the
ground wire to the BLACK ground wire on the RVCCH-75DC harness.
Chassis Ground
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
2 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
INSTALLING THE CDR-02 CAMERA AND CABLE
1. Remove the OE tailgate handle.
2. Remove the OE lock cylinder and install in the CDR-02 camera housing.
3. Install the new tailgate handle and run the cables to the radio.
4. Remove the factory radio to gain access to the factory connectors.
5. Route the wires towards the radio and make the power and video connecons. For powering up the camera, use the 12V
OUTPUT (White Wire). (See Wiring Diagram on page 1)
6. Connect the camera ground wire to chassis ground. If video noise is present, we recommend connecng a ground wire
from the camera to the BLACK wire on the RVCCH-75DC T-harness.
7. The CDR-02 has a built-in parking guide lines opon and is defaulted to ON from the factory. To turn OFF the parking guide
lines, cut the thin WHITE wire located on the camera cable 4 feet from the camera. Unplug the barrel connectors on the
cable for 10 seconds. Align the arrows on the barrel connectors and rmly plug them together.
8. Test the camera before re-installing the radio.
CODING THE RADIO FOR A REAR VIEW CAMERA
The radio has to be coded to accept a reverse camera. Please follow the coding procedure below:
1) Turn key o and remove the key from ignion.
2) Open the driver door then close it (make sure all doors, li gate and hood are also closed).
3) Look at the module and wait for LEDs to turn o then disconnect the module.
4) Before plugging back the module, turn all DIP switches to ON then OFF.
5) Set DIP switches to the sengs provided above.
6) Reconnect module and wait for the LEDs to turn o.
7) Start engine and the coding operaon is now complete.
8) Put the gear in reverse to test the camera.
DIP SWITCH FUNCTIONS:
DIP 1 = Set to OFF
DIP 2 = Rear View Camera ON / OFF
DIP 3 = Set to OFF
DIP 4 = Set to OFF
DIP 5 = Defaulted to OFF*
DIP 6 = Defaulted to ON*
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
*DIP 5 & 6
If the radio is having turn-on issues, please try the following:
Aempt 1: Set 5 & 6 to ON
Aempt 2: Set 5 to ON and 6 to OFF
Aempt 3: Set 5 to OFF and 6 to ON
1 2 3 4 5 6
ON
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
3 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
VEHICLE APPLICATIONS:
RAM
2013 - 2017 1500
2013 - 2017 2500
2013 - 2017 3500
NOTES:
1. Not compable with diesel powered trucks.
2. Not compble with RAM trucks with factory installed cargo camera.
COMPATIBLE RADIOS:
8.4” Screen with Separate Knobs 5” Screen with 6 Buons &
Separate Knobs
4.3” Screen with 6 Buons &
2 Knobs
4.3” Screen with 4 Buons & 2 Knobs
Not compable radio
Especificaciones del producto
| Marca: | CRUX |
| Categoría: | cámara de marcha atrás |
| Modelo: | RVCCH-75DC |
¿Necesitas ayuda?
Si necesitas ayuda con CRUX RVCCH-75DC haz una pregunta a continuación y otros usuarios te responderán
cámara de marcha atrás CRUX Manuales
28 Agosto 2024
28 Agosto 2024
28 Agosto 2024
27 Agosto 2024
27 Agosto 2024
26 Agosto 2024
24 Agosto 2024
24 Agosto 2024
21 Agosto 2024
20 Agosto 2024
cámara de marcha atrás Manuales
- cámara de marcha atrás AEG
- cámara de marcha atrás Garmin
- cámara de marcha atrás Kenwood
- cámara de marcha atrás Pioneer
- cámara de marcha atrás Alpine
- cámara de marcha atrás Pyle
- cámara de marcha atrás Dometic
- cámara de marcha atrás Marquant
- cámara de marcha atrás Trebs
- cámara de marcha atrás Pro-User
- cámara de marcha atrás Audiovox
- cámara de marcha atrás Waeco
- cámara de marcha atrás Tracer
- cámara de marcha atrás Boyo
- cámara de marcha atrás VDO Dayton
- cámara de marcha atrás Valeo
- cámara de marcha atrás Luis
- cámara de marcha atrás Beeper
- cámara de marcha atrás Camos
- cámara de marcha atrás Mobiset
- cámara de marcha atrás AutoXtreme
Últimos cámara de marcha atrás Manuales
26 Octubre 2024
21 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
19 Septiembre 2024
18 Septiembre 2024
15 Septiembre 2024
15 Septiembre 2024