CyberData Systems 011181 Manual de Usario

CyberData Systems Vocero 011181

Lee a continuación 📖 el manual en español para CyberData Systems 011181 (4 páginas) en la categoría Vocero. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Quick Start Guide 930466A

The IP Endpo int Company

1.0 Out-of-Box and Prior to Final Installation

1.1. Verify that you have received all of the parts listed on the Installation Quick

Reference placemat.

1.2. Download the current manual, otherwise known as an Operation Guide,

which is available on the Documentation page at the following website

address:

http://www.cyberdata.net/products/voip/digitalanalog/ceilingspkr2ptt/docs.html

Note You can also navigate to the Documentation page by going to

www.CyberData.net and following the steps that are indicated by

the following figures:

2.0 Select Power Source

PoE Switch PoE Injector

Set PoE power type to Class 0 = 15.4W CAT6 cable recommended—

for longer distances

Be sure you are using a non-PoE switch or port

Make sure port is not in trunk mode

Set port to full duplex/ 100mbps

Spanning Tree Protocol (STP) must be disabled or Portfast enabled

VoIP V2 Ceiling Speaker, Push-to-Talk,

Quick Start Guide

Quick Start Guide 930466A

3.0 Power Test

3.1. Plug in the CyberData device and monitor the LED activity on the front of

the device. See the following figure:

3.2. The GREEN power/status LED and the YELLOW network LED come on

immediately. The YELLOW network LED will blink to indicate network

traffic. After about 27 seconds, the GREEN power/status LED will blink

twice to indicate that the board is fully booted.

If there is no DHCP server available on the network, it will try 12 times with

a three second delay between tries and eventually fall back to the

programmed static IP address (by default 10.10.10.10). This process will

take approximately 80 seconds.

3.3. When the device has completed the initialization process, press and hold the

RTFM switch for 3 seconds to announce the IP address.

This concludes the power test. Go to Section 4.0, "Connecting to a Network

in a Test Environment".

Speaker

Status

(Green LED)

Network

Link/Activity

(Yellow LED)

Quick Start Guide 930466A

4.0 Connecting to a Network in a Test Environment

Note The following connections are usually needed for this procedure:

• PC

• PoE switch or injector

• CyberData device

4.1. In a test environment, use a PC that is connected to the same switch as a

single CyberData device. Note the subnet of the test PC.

4.2. Use the CyberData Discovery Utility program to locate the device on the

network. You can download the Discovery Utility program from the

following website address:

http://www.cyberdata.net/support/voip/discovery_utility.html

4.3. Wait for initialization to complete before using the Discovery Utility

program to scan for a device. The device will show the current IP address,

MAC address, and serial number.

4.4. Select the device.

Note If the IP address of the device is in the same subnet of the PC, then

go to Step 4.7.

4.5. If the IP address of the device is different from the subnet of the PC, then

complete the following steps:

4.5.1. Click the Details tab.

4.5.2. Click Adv. Config to manually configure settings with an available IP

address in the same subnet.

Note A gateway address of 0.0.0.0 or a subnet address of

255.255.255.255 will prompt you to enter a valid address.

4.5.3. Click OK after you are finished making changes.

4.6. A dialog box will prompt you to click OK after confirming the configuration

changes and will ask you to wait while the device reboots. Please wait for

the device to power up and wait for the Discovery Utility program to find

the device on the network.

Especificaciones del producto

Marca:	CyberData Systems
Categoría:	Vocero
Modelo:	011181

¿Necesitas ayuda?

Si necesitas ayuda con CyberData Systems 011181 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Vocero CyberData Systems Manuales

CyberData Systems SIP 011398 Manual de Usario

26 Octubre 2024

CyberData Systems SIP 011393 Manual de Usario

13 Septiembre 2024

CyberData Systems Singlewire 011182 Manual de Usario

13 Septiembre 2024

CyberData Systems SIP-enabled IP V2 Manual de Usario

13 Septiembre 2024

CyberData Systems SIP IP66 Manual de Usario

12 Septiembre 2024

CyberData Systems 11394 Manual de Usario

8 Septiembre 2024

CyberData Systems 011520 Manual de Usario

8 Septiembre 2024

CyberData Systems 011180 Manual de Usario

8 Septiembre 2024

CyberData Systems 011487 Manual de Usario

8 Septiembre 2024

CyberData Systems InformaCast Manual de Usario

8 Septiembre 2024

Vocero Manuales

Últimos Vocero Manuales

Continental Edison CELED53HP20V2B4 Manual de Usario

27 Octubre 2024

Canton Vento 830.2 Manual de Usario

27 Octubre 2024

Jamo S7-25C Manual de Usario

27 Octubre 2024

Bowers Wilkins 707 S2 Manual de Usario

27 Octubre 2024

Monacor GLS-301/GR Manual de Usario

27 Octubre 2024

Monitor Audio Silver C150 Manual de Usario

26 Octubre 2024

FBT MITUS 210M Manual de Usario

26 Octubre 2024

Lamax PartyGo1 Play Manual de Usario

26 Octubre 2024

IKEA SYMFONISK 405.847.50 Manual de Usario

26 Octubre 2024

IKEA SYMFONISK 804.923.34 Manual de Usario

26 Octubre 2024