CyberPower BRG1500AVRLCD2 Manual de Usario

CyberPower No categorizado BRG1500AVRLCD2

Lee a continuación 📖 el manual en español para CyberPower BRG1500AVRLCD2 (3 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

YOUR ULTIMATE ALLY IN POWER

BRG1500AVRLCD2

USER MANUAL

Cyber Power Systems (USA), Inc. 4241 12th Avenue East, Suite 400 | Shakopee, MN 55379 | CyberPowerSystems.com

IMPORTANT SAFETY WARNINGS (SAVE THESE INSTRUCTIONS)

When using electrical appliances, basic safety precautions should always be followed to

reduce the risk of fire, electric shock, and/or injury to persons including the following. This

Manual Contains Important Instructions that should be followed during installation and

maintenance of the UPS and batteries.

CAUTION! To prevent the risk of fire or

electric shock, install in a temperature

and humidity controlled indoor area free

of conductive contaminants. (Please see

specifications for acceptable temperature

and humidity range).

CAUTION! To reduce the risk of electric

shock, do not remove the cover except to

service the battery. Turn off and unplug the

unit before servicing the batteries. There

are no user serviceable parts inside except

for the battery.

CAUTION! Hazardous live parts inside can

be energized by the battery even when the

AC input power is disconnected.

CAUTION! The UPS must be connected

to an AC power outlet with fuse or circuit

breaker protection. Do not plug into an

outlet that is not grounded. If you need to

de-energize this equipment, turn off and

unplug the unit.

CAUTION! To avoid electric shock, turn off

the unit and unplug it from the AC power

source before servicing the battery.

CAUTION! Not for use in a computer

room as defined in the Standard for the

Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

CAUTION! To reduce the risk of fire,

connect only to a circuit provided with

20 amperes maximum branch circuit over

current protection in accordance with the

National Electric Code, ANSI/NFPA 70.

DO NOT USE FOR MEDICAL OR LIFE

SUPPORT EQUIPMENT! CyberPower

Systems does not sell products for life

support or medical applications. DO NOT

use in any circumstance that would affect

the operation and safety of life support

equipment, medical applications, or patient

care.

DO NOT USE WITH OR NEAR

AQUARIUMS! To reduce the risk of fire

or electric shock, do not use with or near

an aquarium. Condensation from the

aquarium can cause the unit to short out.

DO NOT USE THE UPS ON ANY

TRANSPORTATION! To reduce the risk of

fire or electric shock, do not use the unit

on any transportation such as airplanes

or ships. The effect of shock or vibration

caused during transit and the damp

environment can cause the unit to short

out.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box

should contain the following:

(a) UPS

(b) User’s manual

(d) Function Setup Guide

*PowerPanel Business software is

available on our website. Please visit

cyberpowersystems.com and go to the

Software Section for free download.

OVERVIEW

The BRG1500AVRLCD2 provides

complete power protection from utility

power that is not always consistent. The

BRG1500AVRLCD2 features 1500 Joules

of surge protection. The unit provides

long lasting battery backup during power

outages with maintenance free batteries.

The BRG1500AVRLCD2 ensures consistent

power to your computer system and

includes software that will automatically

save your open files and shutdown your

computer system during a utility power

loss.

AUTOMATIC VOLTAGE REGULATOR

The BRG1500AVRLCD2 stabilizes

inconsistent utility power voltage to

nominal levels that are safe for equipment.

Inconsistent incoming utility power may

be damaging to important data files and

hardware, but with Automatic Voltage

Regulation (AVR), damaging voltage

levels are corrected to safe levels. AVR

automatically increases low utility power

and decreases high utility power to a

consistent and safe 110/120 volts.

DETERMINE THE POWER REQUIREMENTS

OF YOUR EQUIPMENT

1 . Ensure that the equipment plugged into

the outlet does not exceed the UPS’s

rated capacity. If the rated capacity

of the unit is exceeded, an overload

condition may occur and cause the UPS

to shut down or the circuit breaker to

trip.

2 . There are many factors that can

affect the amount of power that your

computer system will require. It is

suggested that the load placed on the

battery outlets not exceed 80% of the

unit’s capacity. REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid batteries collect used batteries for recycling, as required by

local regulations.

K01-0000972-00

1 . Power Switch: Used as the master on/

off switch for equipment connected

to the battery power supplied outlets.

2 . Power On Indicator: This LED is

illuminated when the utility power

is normal and the UPS outlets are

providing power, free of surges and

spikes.

3 . LCD module display: The LCD

display shows all the UPS information

using icons and messages. For

more information please review the

“Definitions for Illuminated LCD

Indicators” section.

4 . Down/Display button: The button

can be used to select the LCD display

contents including Input Voltage,

Output Voltage, and Estimated Run

Time. Short press the button to scroll

down the function menu. Pressing the

button for 2 seconds will keep the

LCD display always on or turn the LCD

display off while in AC/Utility power

mode. For more information about

the Down/Display Button, please refer

to the Function Setup Guide.

5 . Up/Mute button: Short press the

button to scroll up the function menu.

Holding the button for more than 2

seconds will silence the alarm. For

more information about the Up/Mute

Button, please refer to the Function

Setup Guide.

6 . Enter/Setup button: Press the button

for 2 seconds to enter the setup menu

and then select the functions for

configuration. For more information

about the Enter/Setup Button, please

refer to the Function Setup Guide.

7 . USB Charging Ports: The USB

Charging ports provide 5Vdc, 2.5A

Max / 9Vdc, 2A Max (USB-C), and

5Vdc, 2.4A Max (USB-A). Total Output

Current: 30W.

8 . Battery and Surge Protected

Outlets: The UPS has six battery

powered/surge suppression outlets

for connected equipment to ensure

temporary uninterrupted operation

of your equipment during a power

failure. (DO NOT plug a laser printer,

paper shredder, copier, space heater,

vacuum, sump pump or other large

electrical devices into the “Battery

and Surge Protected Outlets”. The

power demands of these devices may

overload and damage the unit.)

9 . Full-Time Surge Protection Outlets:

The UPS has six surge suppression

outlets.

10 . Circuit Breaker: Located on the back

of the UPS, the circuit breaker serves to

provide overload and fault protection.

11 . USB Port to PC: The USB port allows

connection and communication

between the USB port on the computer

and the UPS unit.

DB9 Port: The DB9 port is used for

connecting between the UPS and

equipment designed to operate with a

dry contact closure.

12 . Wiring Fault Indicator (red): This

LED indicator will illuminate to warn

the user that a wiring problem exists,

such as bad ground, missing ground or

reversed wiring. If this is illuminated,

disconnect all electrical equipment

from the outlet and have an electrician

verify the outlet is properly wired. The

UPS will not provide surge protection

without being plugged into a grounded

and properly wired wall outlet.

13 . Communication Protection Ports

(RJ45):Communication protection

ports, bi-directional, will protect a

10/100/1000 Ethernet connection.

14 . Expansion Slot: Remove the cover

panel to install an optional RMCARD

to remotely monitor and manage the

UPS over a network. Other options

include cloud monitoring via a mobile

app and web-based app (RCCARD or

RWCCARD).

BASIC OPERATION

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used

immediately upon receipt. However,

after receiving a new UPS, to ensure

the battery’s maximum charge capacity,

it is recommended that you charge the

battery for at least 8 hours. Your UPS is

equipped with an auto-charge feature.

When the UPS is plugged into an AC

outlet, the battery will automatically

charge whether the UPS is turned on or

off.

Note: This UPS is designed with a

safety feature to keep the system from

being turned on during shipment. The

first time you turn the UPS on, you will

need to have it connected to AC power

or it will not power up.

2. With the UPS

unit turned off

and unplugged,

connect your

computer, monitor,

and any other peripherals requiring

battery backup into the battery power

supplied outlets. DO NOT plug a

laser printer, paper shredder, copier,

space heater, vacuum, sump pump

or other large electrical devices into

the “Battery and Surge Protected

Outlets”. The power demands of these

devices may overload and damage the

UPS.

3. Plug the UPS into a 2 pole, 3 wire

grounded receptacle (wall outlet).

Make sure the wall branch outlet is

protected by a fuse or circuit breaker

and does not service equipment with

large electrical demands (e.g. air

conditioner, copier, etc.). The warranty

prohibits the use of extension cords,

outlet strips, and surge strips.

4. Press the power switch to turn the unit

on. The Power On indicator light will

illuminate and the unit will “beep”. If an

overload is detected, an audible alarm

will sound and the unit will emit one

long beep. To correct this, turn the

UPS off and unplug at least one piece

of equipment from the battery power

supplied outlets. Make sure the circuit

breaker is depressed and then turn the

UPS on.

5. To maintain optimal battery charge,

leave the UPS plugged into an AC

outlet at all times.

6. To store the UPS for an extended

period, cover it and store with the

battery fully charged. While in storage,

recharge the battery every three

months to ensure battery life.

7. Ensure the wall outlet and UPS are

located near the equipment being

attached for proper accessibility.

INSTALLING YOUR UPS SYSTEM - Continued

PLUG IN

PRODUCT REGISTRATION

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at: cyberpowersystems.com/registration. Registration certifies your product's warranty,

confirms your ownership in the event of a product loss or theft and entitles you to free technical support. Register your product now to receive the benefits of CyberPower ownership.

FEATURES

1 . Power Switch

2 . Power On Indicator

3 . LCD module display

4 . Down/Display button

5 . Up/Mute button

6 . Enter/Setup button

7 . USB Charging Ports

8 . Battery and Surge Protected Outlets

9 . Full-Time Surge Protection Outlets

10 . Circuit Breaker

1 1 . USB Port to PC/DB9 Port

12 . Wiring Fault Indicator (red)

13 . Communication Protection Ports

14 . Expansion Slot

SERIAL

REFER TO

BOTTOM OF

UNIT FOR

ELECTRICAL

CAUTIONS

710

Replacement of batteries located in an OPERATOR ACCESS AREA.

1 . When replacing batteries, replace with the same number of the following battery:

CyberPower / RB1290x2E

2 . CAUTION! Risk of Energy Hazard, 24 V, maximum 9 Ampere-hour battery. Before

replacing batteries, remove conductive jewelry such as chains, wrist watches, and

rings. High energy conducted through these materials could cause severe burns.

3 . CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

4 . CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin

and eyes. It may be toxic.

5 . CAUTION! A battery can present a risk of electrical shock and high short circuit

current. The following precautions should be observed when working on batteries:

1) Remove watches rings, or other metal objects.

2) Use tools with insulated handles.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

DISPOSE OF USED BATTERIES ACCORDING TO LOCAL REGULATIONS.

REPLACING THE BATTERY BATTERY REPLACEMENT PROCEDURE:

1 . Switch off and unplug all the connected equipment.

2 . Switch off the UPS and disconnect it from the wall outlet.

3 . Place the product on its side, on a solid and stable surface.

4 . Loosen the battery compartment cover screws.

5 . Press on the locking latch and slide the battery compartment cover.

6 . Using the handles on both sides of the battery pack, lift the battery pack 30 degrees

upward to expose the battery onnector. Connect the wires as shown above.

7 . Replace the new battery pack into the unit and connect the wires as above steps

8 . Align the side rails on the cover with the rails on the UPS and slide the cover till it

locks and screws in position.

9 . Recharge the UPS for 8-16 hours to fully charge the battery.

1 2 3

4 5

(+) RED (-) BLACK

CONNECT BATTERY

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

TROUBLESHOOTING

1 . ONLINE:

The UPS is supplying utility power to connected equipment.

2 . ENERGY-SAVING:

The UPS in energy-saving bypass mode. See “CyberPower GreenPower UPS™

Technology” section for more information.

3 . AVR (Automatic Voltage Regulation):

This icon appears whenever your UPS is automatically correcting low or high AC line

voltage without using battery power. This is a normal, automatic operation of your

UPS, and no action is required on your part.

4 . ON BATTERY:

During a loss in power or severe sag, this icon appears and an alarm sounds (two

short beeps followed by a pause) to indicate the UPS is operating from its internal

batteries. During a prolonged loss in power, the alarm will beep rapidly every 1/2

second o indicate the UPS’s batteries are nearly out of power. You should save files

and turn off your equipment immediately or allow the software to shut the system

down.

5 . BATTERY CAPACITY:

This meter displays the approximate charge level (in 20% increments) of the UPS’s

internal battery. During a loss in power or severe sag, the UPS switches to battery

power, the BATTERY icon appears, and the charge level decreases.

6 . REPLACE BATTERY:

The icon illuminates when the batteries are not connected well or the batteries are

worn out.

7 . FAULT:

This icon appears if there is a problem with the UPS. Press the POWER button to

turn the UPS off.

E02: Charger Fault-No Charge (Contact CyberPower Systems for support.)

E11: Battery Overvoltage (Contact CyberPower Systems for support.)

E21: Output Short (Check the status of equipment connected to the UPS and then

turn on the UPS again.)

E22: Overload (Unplug at least one piece of equipment from battery outlets and turn

the UPS on again.)

8. OVER LOAD:

This icon appears and an alarm sounds to indicate the battery-supplied outlets are

overloaded. To clear the overload, unplug one piece of equipment from the battery-

supplied outlets at a time until the icon turns off and the alarm stops.

9 . CURRENT LOAD:

This meter displays the approximate output load level (in 20% increments) of the

UPS battery outlets.

10 . SCHEDULE:

Users can setup the schedule to turn on and shut down the computer and UPS

through PowerPanel Business software. The LCD display will show how much time is

left before the UPS will turn back on or shut down.

11 . MUTE:

This icon appears whenever the UPS is in silent mode. However, when there is a

problem with the UPS, the alarm will still beep even in silent mode.

12 . SENSITIVITY SETUP:

This meter is also used to setup the UPS sensitivity when you are in the programming

mode. If the connected equipment can tolerate more power events (example:

unstable power often associated with stormy weather), select Low Sensitivity and

the UPS will go to Battery Mode less often. If the connected equipment is more

sensitive to power events, select High Sensitivity and the UPS will go to Battery

Mode more often.

13 . ESTIMATED RUNTIME:

This displays the runtime estimate of the UPS with current battery capacity and load.

14 . OUTPUT METER:

This meter measure, in real time, the AC voltage that the UPS system is providing to

the computer, such as normal AC line mode, AVR mode, and battery backup mode.

(Note: The OUTPUT meter shows the status of the battery backup outlets in terms of

load, frequency, and voltage.)

15 . EVENT:

This meter records the number of power outages.

16 . INPUT METER:

This meter measures the AC voltage that the UPS system is receiving from the utility

wall outlet. The INPUT voltage meter can be used as a diagnostic tool to identify

poor-quality input power.

For more information about functions setup, please refer to the Function Setup Guide.

Problem Possible Cause Solution

Circuit breaker button is projecting from the back of

the unit. Circuit breaker has tripped due to an overload.

Turn the UPS off and unplug at least one piece of equipment.

Wait 10 seconds, reset the circuit breaker by depressing the

button, and then turn the UPS on.

The UPS does not perform expected runtime.

Battery not fully charged. Recharge the battery by leaving the UPS plugged in.

Battery is worn out. Please contact CyberPower Systems about replacement

batteries.

The UPS will not turn on.

The on/off switch is designed to prevent damage from

rapidly turning it off and on. Turn the UPS off. Wait 10 seconds and then turn the UPS on.

The unit is not connected to an AC outlet. The unit must be connected to a 120V 60Hz outlet.

The battery is worn out. Please contact CyberPower Systems.

Mechanical problem. Please contact CyberPower Systems.

PowerPanel Business is inactive (all icons are gray).

The USB cable is not connected.

Connect the USB cable to the UPS unit and an open USB port

on the back of the computer. You must use the cable that came

with the unit.

The USB cable is connected to the wrong port. Check the back of the computer for an additional USB port.

Move the cable to this port.

The unit is not providing battery power. Shutdown your computer and turn the UPS off. Wait 10 seconds

and turn the UPS back on. This should reset the unit.

The USB charging ports are not providing power to the

connected devices.

The USB charging ports have Over Current Protection

design. When the total current of connected devices is over

specification, the USB charging ports will stop providing

power to the connected devices.

Turn the UPS off and unplug at least of device connected to the

USB charging ports and then turn the UPS on.

Additional troubleshooting information can be found under “Support” at www.cyberpowersystems.com

TECHNICAL SPECIFICATIONS

Model BRG1500AVRLCD2

Capacity 1500VA / 900W

Nominal Input Voltage 120V

Input Frequency 60 Hz ± 3 Hz

On-Battery Output Voltage 120Vac ± 5%

Max. Load for UPS Outlets (6 Outlets) 1500VA / 900W

Max. Load for

Full-Time Surge Protection outlets (12 Outlets) 12 Amp

On-Battery Output Wave Form Simulated Sine Wave

Operating Temperature + 32°F to 104° F / 0° C to 40° C

Operating Relative Humidity 0 to 90% non-condensing

Size (W x H x D) 3.9" x 10.2" x 13.8" (100 x 259 x 350 mm)

Net Weight 25.86lbs / 11.73kg

Battery Type CyberPower / RB1290X2E

Typical Battery Recharge Time 8 hours to 90% capacity from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778(UPS), CSA C22.2 No. 107, FCC/DoC Class B

SYSTEM FUNCTIONAL BLOCK DIAGRAM

Input Output

EMI Fllter Surge

Suppressor AVR

Charger

AC / DC Battery Inverter

Normal Mode

Battery Mode

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following measures:

FCC COMPLIANCE STATEMENT

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

Advanced Energy-Saving Patented Bypass Technology

CyberPower’s patented GreenPower UPS™ with Bypass Technology

reduces UPS energy costs by up to 75% compared to conventional UPS

models. Even when utility power is normal, conventional UPS models

constantly pass power through a transformer. By contrast, under normal

conditions the advanced circuitry of a GreenPower UPS™ bypasses the

transformer. As a result, the power efficiency is significantly increased

while decreasing waste heat, using less energy, and reducing energy costs.

When an abnormal power condition occurs, the GreenPower UPS™ automatically runs power

through its transformer to regulate voltage and provide “safe” power. Since utility power is

normal over 88% of the time, the GreenPower UPS™ operates primarily in its efficient bypass

mode.

The GreenPower UPS™ is also manufactured in accordance with the Restriction on

Hazardous Substances (RoHS) directive making it one of the most environmentally-friendly

on the market today.

REEN

POWER UPS

™

Energy-Saving Technology

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment to an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help"

Warning: Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Canadian Compliance Statement

CAN ICES-3 (B)/NMB-3(B)

FCC COMPLIANCE STATEMENT - Continued

LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARANTEE

Please visit www.CyberPowerSystems.com for a copy of the Limited Warranty and

Connected Equipment Guarantee.

Where Can I Get More Information?

The application of the United Nations Convention of Contracts for the International Sale of

Goods is expressly excluded. CyberPower is the warrantor under this Limited Warranty.

For further information please feel free to contact CyberPower at:

Cyber Power Systems (USA), Inc.

4241 12th Ave E., STE 400, Shakopee, MN 55379;

Call us at (877) 297-6937;

or submit a web ticket online at cyberpowersystems.com/support.

WARNING: This product can expose you to chemicals including bisphenol A (BPA) and

styrene, which is known to the State of California to cause reproductive harm and cancer.

For more information, go to www.P65Warnings.ca.gov.

CyberPowerSystems.com

PowerPanel Business is a trademark of

Cyber Power Systems (USA) Inc.

11 1 2 3 7

4 5 6

Especificaciones del producto

Marca:	CyberPower
Categoría:	No categorizado
Modelo:	BRG1500AVRLCD2

¿Necesitas ayuda?

Si necesitas ayuda con CyberPower BRG1500AVRLCD2 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado CyberPower Manuales

CyberPower Rackbar RKBS20ST6F12R Manual de Usario

12 Octubre 2024

CyberPower PR1000ELCDRT2U Manual de Usario

10 Octubre 2024

CyberPower Essential B704 Manual de Usario

10 Octubre 2024

CyberPower Rackbar RKBS20ST6F8R Manual de Usario

7 Octubre 2024

CyberPower RMCARD305 Manual de Usario

4 Octubre 2024

CyberPower Professional CSP708T Manual de Usario

4 Octubre 2024

CyberPower SB0602BA-DE-B50 Manual de Usario

24 Septiembre 2024

CyberPower SB0802AD-DE-W24 Manual de Usario

24 Septiembre 2024

CyberPower SB0502BA-DE-B70 Manual de Usario

24 Septiembre 2024

CyberPower SB0502BA-DE-W70 Manual de Usario

24 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024