Da-Lite Da-Lift 15 78088 Manual de Usario

Da-Lite No categorizado Da-Lift 15 78088

Lee a continuación 📖 el manual en español para Da-Lite Da-Lift 15 78088 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
INSTRUCTION BOOK FOR
Da-Lift Projector Lift
10M, 15M, 15, 19, 19L
2
Important Safety Instructions Pre-Installation
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended
by the manufacturer may cause a risk of ire, electric shock,
or injury to persons.
Save These Instructions
This unit must be installed in accordance with the requirements
of the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC) NFPA 70.
1. Carefully unpack Da-Lift projector lift.
2. Make sure to recheck measurements of projector lift location
before installation.
3
Suggested Methods Of Installation
1. Mounting Da-Lift Projector Lift between joists.
Install the joists at the proper height and width to it the Da-Lift
you are installing. See Figure 1.
NOTE: The Da-Lift must be installed on top of the joists.
Be sure to leave access from above for installation.
When the joists are properly installed, and secured in place, slide
the Da-Lift in position. Bolt the two brackets (11/2” x 19”) to the
frame. Lower the unit onto the joists and secure in place.
Additional bracing may be required, based on construction.
NOTE: Da-Lift projector lift must be installed level!
2. Mounting Da-Lift Projector Lift using 1/2” diameter threaded rods.
Secure four 1/2” diameter threaded rods to the ceiling at the
dimensions shown. See Figure 2, “E” and “F”. Install the mounting
bracket (11/2” x 19”) to each side of Da-Lift with 1/2” diameter bolts,
lat washers and nuts. Attach one nut on each rod and run the
nut up to the desired height.
Slide Da-Lift projector lift up with all (4) four threaded rods into
the mounting brackets. Install 1/2” nuts under the mounting
brackets. Adjust the frame to the proper height and level with
bottom nuts on the rod. Lock the mounting brackets in place
with the nuts on the top of each rod. Frame must be level and
solid. Additional bracing may be required, based on construction.
Model Lifting
Capacity
Width
A
Height
B
Depth
C
Height
D
DIm.
E
Dim.
F
Da-Lift 10M 40 lbs. 22⅝” 4½” 24⅛15” 22 14”
Da-Lift 15M 40 lbs. 22⅝” 9½ 24⅛”20” 22 14
Da-Lift 15 300 lbs. 30¾” 9½ 32¼” 16¼20” 34”
Da-Lift 19 300 lbs. 32¾” 24” 38” 13½ 34¼” 16¼”
Da-Lift 19L 300 lbs. 42¾” 24” 48” 13½” 44¼” 16¼”
Figure 1 Figure 2
A
C
B
D
EF

Especificaciones del producto

Marca: Da-Lite
Categoría: No categorizado
Modelo: Da-Lift 15 78088

¿Necesitas ayuda?

Si necesitas ayuda con Da-Lite Da-Lift 15 78088 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Da-Lite Manuales

No categorizado Manuales

Últimos No categorizado Manuales