Da-Lite Da-Tex (Rear) Manual de Usario

Da-Lite pantalla de proyección Da-Tex (Rear)

Lee a continuación 📖 el manual en español para Da-Lite Da-Tex (Rear) (8 páginas) en la categoría pantalla de proyección. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/8
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
Instruction Book for
TENSIONED ADVANTAGE® ELECTROL®
The Da-Lite Difference.
1
1. Remove 2 screws to open junction box.
2. Hang case and attach to support structure with threaded rod. See suggested methods of installation on page 5.
3. Tighten bolts until trim flange is flush with ceiling.
NOTE: For proper operation, screen assembly must be level after installation.
4. Install electrical connections that applies to your unit. Make sure to review the wiring diagram for proper hook up.
NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
5. Replace junction box cover and secure with 2 screws.
6. If screen and case are purchased together, remove slat retainer brackets from the screen case and back of slat.
PRE-INSTALLATION
1. Carefully unpack case from shipping carton. DO NOT unpack fabric and roller assembly yet.
2. Make sure to recheck measurement of case for proper installation clearance.
3. Remove any protective foam or tape from case.
CASE INSTALLATION
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions should always be followed, including the
following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance
should be used. Cords rated for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized
service dealer when repair work is required. Incorrect reassembly can cause electric shock when
the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the manufacturer may cause a risk of
fire, electric shock, or injury to persons.
SAVE THESE INSTRUCTIONS
If your screen was shipped with the motor and roller already installed, proceed to step 6.
1. Remove access door. First, remove the 2 screws from the ends. Be sure to support the door during this
step to avoid injury. Then lift the door slightly and pull away from the edge of the case.
2. Carefully unpack screen and roller assembly. Leave packing paper on roller.
3. To install screen and roller assembly, insert the motor end into the motor mount bracket as shown in Fig. 1.
4. Loosen (but do not remove) two 1/4-20 nuts securing pin end bracket (stage left) to the case housing. Slide the
bracket towards the end of the case. Insert the motor end square shaft into the motor end bracket and secure with
the clip.Insert the tip of the roller pin end into the bracket and position. Tighten the 1/4-20 nuts securely.
5. Complete electrical hook-up by snapping motor wire connector into case connector.
6. Carefully remove paper and tape from roller assembly. use a knife or sharp object to cut tape; you will DO NOT
damage the screen.
7. Test installation by running screen up and down a few times. Be prepared to stop screen. Standard Duty Cycle: 1
MIN. ON / 3 MIN. OFF.
8. Re-install access door. Procedure is reverse of removal (step 1).
SCREEN AND ROLLER ASSEMBLY INSTALLATION
2
ADVANTAGE® ELECTROL® INSTALLATION
7-3/4"
6-1/16" 3/8" THREADED ROD
(NOT INCLUDED)
ATTACHED TO
MOUNTING BRACKET
SELF-TRIMMING
FLANGE
6-3/8"
7-3/4"
FINISHED
CEILING
8"
6.42"
3/8" THREADED ROD
(NOT SUPPLIED)
HANGER BRACKET
SEE DETAIL A
7.75"
DETAIL A
7.95"
3.41"
ELECTRICAL
JUNCTION BOX
MOTOR END
VARIABLE POSITION
MOUNTING BRACKET
AUDIENCE
SIDE
6-1/16"
6-7/16"
FIGURE 1

Especificaciones del producto

Marca: Da-Lite
Categoría: pantalla de proyección
Modelo: Da-Tex (Rear)

¿Necesitas ayuda?

Si necesitas ayuda con Da-Lite Da-Tex (Rear) haz una pregunta a continuación y otros usuarios te responderán


pantalla de proyección Da-Lite Manuales

Da-Lite

Da-Lite Designer Manual 76456MO Manual de Usario

6 Octubre 2024
Da-Lite

Da-Lite Cinema Vision Manual de Usario

2 Octubre 2024
Da-Lite

Da-Lite Model C 83401 Manual de Usario

29 Septiembre 2024
Da-Lite

Da-Lite Model B Manual de Usario

27 Septiembre 2024
Da-Lite

Da-Lite Perm-Wall 78676 Manual de Usario

26 Septiembre 2024
Da-Lite

Da-Lite Model C With CSR Manual de Usario

18 Septiembre 2024
Da-Lite

Da-Lite Dual Format Imager 38063EV Manual de Usario

11 Septiembre 2024
Da-Lite

Da-Lite Motorized Scenic Roller Manual de Usario

2 Septiembre 2024
Da-Lite

Da-Lite Dual Masking Electrol Manual de Usario

1 Septiembre 2024
Da-Lite

Da-Lite Cinema Contour 20387V Manual de Usario

30 Agosto 2024

pantalla de proyección Manuales

Últimos pantalla de proyección Manuales

Optoma

Optoma DS-3120PMG Manual de Usario

11 Octubre 2024
Optoma

Optoma DS-9120PMG Manual de Usario

29 Septiembre 2024
Draper

Draper Clarion Manual de Usario

22 Septiembre 2024
Pyle

Pyle PRJSM1006 Manual de Usario

20 Septiembre 2024
EPV

EPV PGF106WH1-A4K Manual de Usario

18 Septiembre 2024
EPV

EPV PGF84WH1 Manual de Usario

18 Septiembre 2024
KHOMO GEAR

KHOMO GEAR GER-1252 Manual de Usario

16 Septiembre 2024
KHOMO GEAR

KHOMO GEAR GER-1273 Manual de Usario

16 Septiembre 2024
Celexon

Celexon Ultramobile Plus Professional 194 x 146 Manual de Usario

15 Septiembre 2024
Celexon

Celexon Statief Economy (4:3) 176 x 132 Manual de Usario

15 Septiembre 2024