Da-Lite Horizon Electrol 96214S Manual de Usario
Da-Lite
pantalla de proyección
Horizon Electrol 96214S
Lee a continuación 📖 el manual en español para Da-Lite Horizon Electrol 96214S (8 páginas) en la categoría pantalla de proyección. Esta guía fue útil para 14 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
INSTRUCTION BOOK FOR
Horizon Electrol®
2
1. Install screen by raising unit into position between joists at one
end only. Install one lag screw in each mounting bracket.
2. Level unit lengthwise with a carpenter’s level and plumb level.
Secure opposite end.
3. Detach access panel by removing screws (Figure 1).
CAUTION! Do not seal in until screen has been secured in
position and properly tested for satisfactory operation.
ATTENTION! Ne ixez pas l'écran jusqu'à ce qu'il ait été
correctement mis en place et qu'il fonctionne
convenablement.
4. Remove the two screws holding the splitter junction box (Figure 2).
5. Unwrap the supplied 25 ft. RJ14 cord. Plug one end into a QEYE
port on the primary splitter (see wiring diagram).
6. Run the 25 ft. RJ14 card to the back of the wall keypad and plug
into the RJ receptacle.
7. Remove the two screws holding the junction box cover plate.
Install the electrical hookup (see wiring diagram).
NOTE: Must be installed in accordance with the requirements of
the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
8. After the electrical connections are completed, replace the
junction box cover plate.
9. Carefully remove tape strips securing picture surface around roller.
CAUTION! Do not cut tape on fabric with knife or any sharp
tool. Pull orange string.
ATTENTION! Ne coupez pas le ruban adhésif sur la toile avec
un couteau ou un outil tranchant. Tirez sur le cordon orange.
10. Carefully remove wood boards securing mask surface to case.
11. Test installation by carefully running picture surface and mask
surfaces up and down several times. Be prepared to stop the
screen. IMPORTANT: Read operating instructions before
testing screen.
NOTE: When rolled down, the picture surface should wrap fully
around the roller. No part of the roller should be exposed. Picture
surface and mask surfaces will automatically stop in the down
position.
CAUTION! Excessive continuous operation may cause
overheating. If this happens, the motors will shut of until they
cool to a normal operating temperature. Duty Cycle of screen
is 1 Min. ON / 3 Min Of.
ATTENTION! Le fonctionnement continu et excessif peut
provoquer une surchaufe.Si cela se produit, les moteurs
s'arrêteront jusqu'à qu'ils se soient refroidis à la température
normale de fonctionnement. Le cycle de fonctionnement est
de 1 min. en marche / 3 min. à l'arrêt.
Pre-Installation
Installation
1. Carefully unpack screen and remove outer wrapping
from case.
Figure 2
Figure 1
Drywall Screw
Access Panel
Machine Screw
Truss Head Screw
Shipping Bracket
Hex Head Screw
Tape Strips
Picture Surface
Slats
Mask Surface
Mask
Motor
Screen
Motor
Junction Box
Splitter
Junction
Box
2. Make sure to recheck measurements of screen location
before installation.
Important Safety Instructions
When using your video equipment, basic safety precautions should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
Save These Instructions
3
Screen Operation
The Horizon has been preset to three or four diferent formats. The screen can be set to any format by pressing the corresponding
button on the keypad. Below is a list of each button function.
IMPORTANT! When operating the switch, press and release buttons. Do not hold the button for more than
three (3) seconds or the button will be reprogrammed to the current screen position.
Native NTSC (1.33:1) Format Screens
1. Lowers screen to NTSC (1.33:1) format. Mast will travel down and
reverse wrap on the roller. The mask it not used for this format.
2. Sets format to HDTV (1.78:1).
3. Sets format to Letterbox (1.85:1).
4. Sets format to Cinemascope (2.35:1).
Native HDTV (1.78:1) Format Screens
1. Lowers screen to HDTV (1.78:1) format. Mast will travel down and
reverse wrap on the roller. The mask it not used for this format.
2. Sets format to Letterbox (1.85:1).
3. Sets format to Cinemascope (2.35:1).
4. Open: User deined preset.
Stop – Stops the screen and mask movement at any position when pressed.
Up – Returns the screen and mask to the up position.
Screen – Runs the screen up and down without mask movement.
Mask – Runs the mask up and down without screen movement.
Wall Keypad
Transmitter
Dual IR/RF
Remote
Format Selection
1 2 3 4
Screen Mask
Up
Stop
Format Selection
1 2 3 4
Screen Mask
Up
Stop
Especificaciones del producto
Marca: | Da-Lite |
Categoría: | pantalla de proyección |
Modelo: | Horizon Electrol 96214S |
¿Necesitas ayuda?
Si necesitas ayuda con Da-Lite Horizon Electrol 96214S haz una pregunta a continuación y otros usuarios te responderán
pantalla de proyección Da-Lite Manuales
6 Octubre 2024
2 Octubre 2024
29 Septiembre 2024
27 Septiembre 2024
26 Septiembre 2024
18 Septiembre 2024
11 Septiembre 2024
22 Agosto 2024
14 Agosto 2024
12 Agosto 2024
pantalla de proyección Manuales
- pantalla de proyección Draper
- pantalla de proyección Pyle
- pantalla de proyección Kodak
- pantalla de proyección Optoma
- pantalla de proyección Nec
- pantalla de proyección Luxburg
- pantalla de proyección Duronic
- pantalla de proyección EluneVision
- pantalla de proyección Celexon
- pantalla de proyección Stewart
- pantalla de proyección Avers
- pantalla de proyección Instaal
- pantalla de proyección Elite ProAV
- pantalla de proyección KHOMO GEAR
- pantalla de proyección EPV
Últimos pantalla de proyección Manuales
11 Octubre 2024
29 Septiembre 2024
22 Septiembre 2024
20 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
Celexon Ultramobile Plus Professional 194 x 146 Manual de Usario
15 Septiembre 2024
15 Septiembre 2024