Dell PowerEdge 6600 Manual de Usario

Dell servidor PowerEdge 6600

Lee a continuación 📖 el manual en español para Dell PowerEdge 6600 (77 páginas) en la categoría servidor. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/77

Dell™PowerEdge™6600SystemsInstallationandTroubleshootingGuide

Introduction

Indicators, Messages, and Codes

Finding Software Solutions

Running the System Diagnostics

TroubleshootingYourSystem

Installing System Options

Installing Drives

Getting Help

Jumpers and Connectors

Abbreviations and Acronyms

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

©2001DellComputerCorporation.Allrightsreserved.

Reproduction in any manner whatsoever without the written permission of Dell Computer Corporation is strictly forbidden.

Trademarks used in this text: Dell, the DELL logo, PowerEdge, Dell OpenManage, Dimension, Inspiron, Dell Precision, OptiPlex, Latitude, and DellNet are trademarks of Dell Computer

Corporation; MS-DOS is a registered trademark of Microsoft Corporation.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation

disclaims any proprietary interest in trademarks and trade names other than its own.

Initial release: 25 Feb 02

NOTE: A NOTE indicates important information that helps you make better use of your computer.

NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.

Back to Contents Page

Jumpers and Connectors

Dell™PowerEdge™6600SystemsInstallationandTroubleshootingGuide

Jumpers—AGeneralExplanation

I/O Riser Card Jumpers and Connectors

I/O Board Connectors and Buses

Microprocessor Board Connectors

SCSI Backplane Board Connectors

Peripheral Riser Card Connectors

Disabling a Forgotten Password

This section provides specific information about the jumpers on the system board. It also provides some basic information on jumpers and switches and

describes the connectors and sockets on the various boards in the system.

Jumpers—AGeneralExplanation

Jumpers provide a convenient and reversible way of reconfiguring the circuitry on a printed circuit board. When reconfiguring the system, you may need to

change jumper settings on the system board. You may also need to change jumper settings on expansion cards or drives.

Jumpers

Jumpers are small blocks on a circuit board with two or more pins emerging from them. Plastic plugs containing a wire fit down over the pins. The wire connects

the pins and creates a circuit. To change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s) indicated. FigureA-1 shows an

example of a jumper.

Figure A- 1. Example Jumpers



A jumper is referred to as open or unjumpered when the plug is pushed down over only one pin or if there is no plug at all. When the plug is pushed down

over two pins, the jumper is referred to as jumpered. The jumper setting is often shown in text as two numbers, such as 1-2. The number 1 is printed on the

circuit board so that you can identify each pin number based on the location of pin 1.

FigureA-2 -1 shows the location and default settings of the jumper blocks on the system board. See TableA for the designations, default settings, and

functions of the system's jumpers.

I/O Riser Card Jumpers and Connectors

FigureA-2 -1 shows the location of the configuration jumpers and connector on the I/O riser card. TableA and TableA-2 list the jumpers and connectors.

Figure A- 2. I/O Riser Card Components



CAUTION: Make sure the system is turned off before you change a jumper setting. Otherwise, damage to the system or unpredictable results may

occur.



I/O Board Connectors and Buses

FigureA-3 shows the expansion slots, buses, and bus operating speeds.

Figure A- 3. I/O Board Connectors and Buses



Table A-1. I/O Riser Card Jumper Settings

Jumper

Setting

Description

NVRAM_CLR

(default)

The configuration settings are retained at system boot.

The configuration settings are cleared at next system boot. (If the configuration settings become corrupted to the point where the

system will not boot, change the jumper setting to 1–2 and boot the system. Change the jumper setting back to 2–3 before

restoring the configuration information.)

PSWD

(default)

The password feature is enabled.

The password feature is disabled.

RSVD

Reserved (do not change).

FVS

Reserved (do not change).

NOTE: For the full name of an abbreviation or acronym used in this table, see "Abbreviations and Acronyms."

Table A-2. I/O Riser Card Connectors

Connector or Socket

Description

INTR

Chassis intrusion switch connector

Back-panel system status indicator

SCSIA

An external SCSI connector on the back panel or an internal tape drive

VBATT

System battery socket

NOTE: See Figure2-3 for back- panel connectors provided by the I/O riser card.

Especificaciones del producto

Marca:	Dell
Categoría:	servidor
Modelo:	PowerEdge 6600
Color del producto:	Black, Green
Peso.:	8550 g
Ancho:	340 mm
Profundidad:	435 mm
Altura:	385 mm
Peso del embalaje:	11330 g
Puerto USB:	Ja
Kijkglas:	Nee
Certificación:	CE, FCC, WEEE
Pinzas:	Ja
voltaje-de-entrada-de-CA:	100/240 V
Consumo de energía (típico):	150 W
Material de impresión:	ABS, HIPS, Nylon, PVA, Polycarbonate (PC), Polylactic acid (PLA)
Velocidad máxima de impresión:	275 mm/sec
Grosor del filamento soportado:	3 mm
Tamaño máximo de impresión:	152 x 152 x 158 mm
Espesor de capa (mín.):	0.05 mm
Espesor de capa (máx.):	0.5 mm
Temperatura máxima de la plataforma de impresión:	120 °C
Plataforma de impresión calentada:	Ja
Volumen del compartimento de impresión:	3.65 l