Delta Dore Tyxia 5731 Manual de Usario
Delta Dore
Receiver
Tyxia 5731
Lee a continuación 📖 el manual en español para Delta Dore Tyxia 5731 (1 páginas) en la categoría Receiver. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/1
Recommendations
• IMPORTANT: the control wires are not
insulated from the mains power supply.
All connected equipment must be marked
CE and meet the requirements of the
low voltage devices as well as assembly
recommendations. Local control wires can
be extended up to 10 m
(separate from the
230 V).
• The roller shutter high and low stops must
be set before the receiver is installed.
• For the control of electric motors, please
contact us.
1 - Installation
1.1 Connection instructions for terminals 1 2 3 4.
- Strip the wires while respecting the strip length
specified on the product.
- Push the wire fully into the terminal.
1.1.1 Solid wires Stranded wires 1.1.2
1.2 Connection instructions for IN1 - COM - IN2 terminals
- Use the wires supplied.
- Push the wire fully into the terminal.
1.3 Connection
- Connect the motor control wires to terminals 3 and 4
(motor lowering control wire to terminal 3, raising control wire to terminal 4).
- Connect the switch to the IN1 - COM - IN2 terminals.
- Connect the 230 V power supply to terminals 1 and 2.
- Switch the installation power back on to continue with the association opera-
tion.
2 - Association
3 - Configuration
Configure the receiver according to
the type of switch connected.
Mode 1: Hold switch
Raise/Stop/Lower
Mode 2 (by default):
Raise/Lower double push-button
Raise + Lower: Stop
Mode 3: Raise/Stop/Lower/Stop
push-button
To modify the receiver configuration.
- Press the receiver's button for 6 seconds.
- The LED flashes, then becomes steady, release.
The number of flashes corresponds
to the current mode.
- Briefly press the receiver button to select the mode
.
- Confirm the selected mode by pressing the button for 3 seconds until the LED
switches off.
4 - Learning for the shutter travel time
Perform a complete cycle from stop to stop:
1- Lower or raise the roller shutter completely to the stop.
2- Do the reverse action until the opposite stop is reached.
Note: The learning for the shutter travel time adjusts itself automatically for
each complete cycle from stop to stop.
5 - Learning for the tilt time
Do not carry out this operation,
if the TYXIA 5731 controls an awning.
- Hold down the receiver button
for 9 seconds, the LED switches off,
then release. The shutter is positioned at the
midpoint of its height
- Press and hold the rotation button
(step by step mode) until the shutter
has rotated fully, then press stop.
- The tilt time is recorded.
6 - Help
Summary of functions:
0,75 - 1,5 mm
Ø
2
2
1
1234
> 6 s
TYXIA
1234
TYXIA
1234
TYXIA
1234
TYXIA
12
Use an electrically
isolated tool to
perform the actions
on the receiver confi-
guration button.
IPx4
230V~
OFF
Switch off the
installation
power supply
You can install the receiver for roller shutter
in a flush-mounted box behind a switch or
control push-button or in a sealed box inside
the roller shutter, a safe distance from metal
parts.
Removal recommendations
- Switch off the power supply.
- Use the tool supplied or a 2.5 mm screwdriver
to press the button of the front terminal before
removing the wire.
2
1
Removal recommendations
Turn the wire while pulling on it.
Do not strip the wires when they are
connected to the product as you
could damage the internal connector.
1
2
123 4
2
7mm 0,5 mm
KY31A02
123 4
230 V~
IN1
COM
IN2
1234
TYXIA
1 2 3 4
IN1
COM
IN2
IN1
COM
IN2
IN1
COM
2
1
3
1
2
1
2
Hold switch
Double
push-button
Push
button
- Press and hold the receiver but-
ton for 3 seconds until the LED
flashes, release.
On the transmitter:
- Send the association command
(Refer to the user guide).
When the receiver LED has
stopped flashing.
The products are associated.
OK
OFF
1 2 3 4
TYXIA
1 2 3 4
... ... ...
> 3s
1 2 3 4
TYXIA TYXIA
TYXIA 2600
TYDOM
A
B
COM
IN1
IN2
CR 20 32
TYXIA
2600
> 3s
A B
> 3s
1 2
3
IN1
COM
IN2
IN1
COM
IN2
IN1
COM
2
1
3
1
2
1
2
Do not interrupt
the roller shut-
ter travel.
Mode 1
Hold
switch
Mode 2
Double
push-button
Mode 3
Push button
• Quick press on the button.
A
Checking the receiver
operating mode.
Briefly press the button.
The LED flashes:
- 1 red flash: MODE 1
- 2 red flashes: MODE 2
- 3 red flashes: MODE 3
• Press and hold the button for
x seconds.
B
Association (refer to §2)
C
Configuration (refer to §3)
D
Learning for the tilt time
(refer to §5)
E
Removing an association
- Press the receiver's button for 12
seconds. (the removal method varies
according to the transmitter associated,
refer to the transmitter's user guide)
F
Removing all associations
- Press the receiver's button for 20
seconds.
- Press and hold until the LED switches off
after the rapid flashing phase.
- Release. The receiver has no wireless
connection.
G
Factory reset
- Press the receiver button for 30 seconds,
the LED flashes then switches off. The
receiver has no wireless connection and
the configuration is reset (mode 1 by
default).
The receiver locks in off mode.
When an overload is detected, the product
locks in off mode for 30 seconds before autho-
rising a new activation. The LED flashes rapidly
throughout this phase.
Contact our customer service.
20A circuit breaker
max. required.
3’’
BA
> > >6’’ 9’’ 20’’>12’’ 30’’>
C D F G
>
E
Association Removing an
association
Configuration
Factory
reset
Removing
all associations
Tilt
time
Using the tool supplied
or a 2.5 mm screwdriver,
press the terminal button
then insert the wire.
For the warranty and protection of your
shutters, we recommend the installation
of a wind sensor.
CV
P/N: 6351393
50%
TYXIA
>9s
Technical characteristics
- Power supply: 230 V~ 0.6 VA
• 2 Powered contact outputs: 2A
- Stand-by consumption: 0.06 W
- Number of associated transmitters:
16 maximum
- Storage temperature: -10°C/+70°C
- Operating temperature:
-10°C/+40°C
- IP 40 (flush mounting box)
- Dimensions: 41 x 36 x 14.5 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum radio power < 10 mW
- Receiver category: 2
EN - Receiver for Blackout Blinds
TYXIA 5731
EN
www.deltadore.com
Especificaciones del producto
Marca: | Delta Dore |
Categoría: | Receiver |
Modelo: | Tyxia 5731 |
¿Necesitas ayuda?
Si necesitas ayuda con Delta Dore Tyxia 5731 haz una pregunta a continuación y otros usuarios te responderán
Receiver Delta Dore Manuales
24 Agosto 2024
20 Agosto 2024
19 Agosto 2024
18 Agosto 2024
Receiver Manuales
- Receiver Sony
- Receiver Philips
- Receiver Garmin
- Receiver JVC
- Receiver JBL
- Receiver Kenwood
- Receiver Onkyo
- Receiver Pioneer
- Receiver Yamaha
- Receiver Alecto
- Receiver Alpine
- Receiver Advance Acoustic
- Receiver Amazon
- Receiver Arcam
- Receiver Ampeg
- Receiver Amplicom
- Receiver Amiko
- Receiver Strong
- Receiver Sharp
- Receiver Silvercrest
- Receiver Nedis
- Receiver Pyle
- Receiver Caliber
- Receiver Vox
- Receiver Hilti
- Receiver Renkforce
- Receiver Bush
- Receiver Sencor
- Receiver Vivanco
- Receiver Blaupunkt
- Receiver Manhattan
- Receiver NAD
- Receiver Harman Kardon
- Receiver Crunch
- Receiver Tripp Lite
- Receiver Vision
- Receiver Imperial
- Receiver Toa
- Receiver Roland
- Receiver DataVideo
- Receiver Axis
- Receiver ART
- Receiver Summit Audio
- Receiver Hifonics
- Receiver Denon
- Receiver Vonyx
- Receiver Sennheiser
- Receiver Elektrobock
- Receiver Chamberlain
- Receiver Avalon
- Receiver Thorens
- Receiver Sonance
- Receiver LD Systems
- Receiver Technisat
- Receiver Bogen
- Receiver Technics
- Receiver Fenton
- Receiver Cisco
- Receiver Krüger And Matz
- Receiver Matrox
- Receiver Kicker
- Receiver Bose
- Receiver Clarion
- Receiver Mackie
- Receiver Teufel
- Receiver Marantz
- Receiver Mac Audio
- Receiver Rega
- Receiver Pro-Ject
- Receiver Kathrein
- Receiver Denson
- Receiver RCF
- Receiver Renegade
- Receiver Peavey
- Receiver Dual
- Receiver Boss
- Receiver McIntosh
- Receiver Behringer
- Receiver Roksan
- Receiver MB Quart
- Receiver Electro-Voice
- Receiver Astro
- Receiver Focal
- Receiver Focusrite
- Receiver Auna
- Receiver Samson
- Receiver Rupert Neve Designs
- Receiver Shure
- Receiver Sherwood
- Receiver QTX
- Receiver Konig
- Receiver Valueline
- Receiver Rotel
- Receiver Icom
- Receiver Chandler
- Receiver Teac
- Receiver RDL
- Receiver JL Audio
- Receiver Magnat
- Receiver Chord
- Receiver Metronic
- Receiver Fiio
- Receiver Anthem
- Receiver Dynacord
- Receiver QSC
- Receiver Iriver
- Receiver Audac
- Receiver Marmitek
- Receiver Lanzar
- Receiver Hertz
- Receiver Zoom
- Receiver Marshall Electronics
- Receiver Hartke
- Receiver Jensen
- Receiver Omnitronic
- Receiver Humax
- Receiver Vaddio
- Receiver Gira
- Receiver Jung
- Receiver Golden Age Project
- Receiver Sangean
- Receiver Apart
- Receiver Line 6
- Receiver Pinnacle
- Receiver Cambridge
- Receiver Radial Engineering
- Receiver ATen
- Receiver Integra
- Receiver Fusion
- Receiver Gefen
- Receiver Scosche
- Receiver Vivotek
- Receiver Mooer
- Receiver Skytec
- Receiver Luxman
- Receiver Infinity
- Receiver DBX
- Receiver Kopul
- Receiver Monitor Audio
- Receiver Monoprice
- Receiver Ibiza Sound
- Receiver Yorkville
- Receiver Axton
- Receiver Proel
- Receiver HQ Power
- Receiver Tangent
- Receiver Edision
- Receiver OSD Audio
- Receiver Crestron
- Receiver RME
- Receiver Adastra
- Receiver Power Dynamics
- Receiver Music Hall
- Receiver Citronic
- Receiver Mercury
- Receiver Definitive Technology
- Receiver Fender
- Receiver Formuler
- Receiver SPL
- Receiver Monacor
- Receiver Lindell Audio
- Receiver StarTech.com
- Receiver HUMANTECHNIK
- Receiver Crest Audio
- Receiver Grace Design
- Receiver Primare
- Receiver Xantech
- Receiver IFi Audio
- Receiver Ferguson
- Receiver Wet Sounds
- Receiver MEE Audio
- Receiver DAP Audio
- Receiver Ibanez
- Receiver Blustream
- Receiver Match
- Receiver Scansonic
- Receiver Helix
- Receiver Crown
- Receiver Kogan
- Receiver Speco Technologies
- Receiver Kemo
- Receiver Morel
- Receiver CE Labs
- Receiver Accell
- Receiver Jolida
- Receiver Ecler
- Receiver Ashdown Engineering
- Receiver Mtx Audio
- Receiver Aquatic AV
- Receiver Parasound
- Receiver Selfsat
- Receiver Kramer
- Receiver CYP
- Receiver Topp Pro
- Receiver AudioControl
- Receiver Cyrus
- Receiver Dimavery
- Receiver LinksPoint
- Receiver Esoteric
- Receiver Markbass
- Receiver Atlas Sound
- Receiver Pyramid
- Receiver LEA
- Receiver SureCall
- Receiver Ram Audio
- Receiver Phonic
- Receiver Koda
- Receiver Lectrosonics
- Receiver Sound Devices
- Receiver Musical Fidelity
- Receiver Triangle
- Receiver Phoenix Gold
- Receiver Audiofrog
- Receiver Memphis Audio
- Receiver CyberData Systems
- Receiver AMX
- Receiver BZBGear
- Receiver Rolls
- Receiver Stewart
- Receiver Crest
- Receiver TechLogix Networx
- Receiver Fosi Audio
- Receiver A-NeuVideo
- Receiver Canor
- Receiver Advance
- Receiver Technical Pro
- Receiver VMV
- Receiver PureLink
- Receiver Glemm
Últimos Receiver Manuales
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024