Durkopp Adler 525 Manual de Usario
Lee a continuación 📖 el manual en español para Durkopp Adler 525 (11 páginas) en la categoría máquina de coser. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/11
Instructions for setting individual mechanisms
525
Minerva Boskovice, a.s., Sokolská 60, CZ - 680 17 Boskovice
Tel.: +420-516 453434, 453433, 494111 Fax: +420-516 452165 http://www.minerva-boskovice.com
Edition: 01/2004 Printed: Czech Republic
Contens - Instructions for setting individual:
1. General safety instructions .............................................................................................................................................. 1
2. Introduction ........................................................................................................................................................................ 1
3. Setting of the feeder height above the throat plate .................................................................................................... 2
4. Setting of the needle and feeder movement ................................................................................................................ 2
5. Mounting of the throat plate ............................................................................................................................................ 2
6. Setting of the elliptical path of the feeder ................................................................................................................... 2
7. Setting of the feeding length .......................................................................................................................................... 3
8. Presser foot replacement ................................................................................................................................................. 3
9. Presser foot lifting setting ............................................................................................................................................... 3
10. Setting of the needle bar height ..................................................................................................................................... 3
11. Adjustment of the hook timing ........................................................................................................................................ 4
12. Setting of the middle part of the hook holder .............................................................................................................. 4
13. Setting of the opening hook of the hook ....................................................................................................................... 5
14. Dismounting and mounting of the driving belt ............................................................................................................ 5
15. Setting the needle punch into the middle of the needle groove
in the throat plate in longitudinal direction ................................................................................................................. 6
16. Setting of the needle punch into the middle of the needle groove
in the throat plate in transversal direction ................................................................................................................... 6
17. Basic setting of the lever and the roller of the decorative ......................................................................................... 6
18. Taking up the teeth clearance of the worm gearing ................................................................................................... 7
19. Setting of the needlebar holder sliding ........................................................................................................................ 7
20. Replacement of the profiled cam ................................................................................................................................... 7
21. Setting of the needle bar and of the hook shaft position ........................................................................................... 7
22. Time setting of the control cam of the thread cutter ................................................................................................... 8
23. Setting of the movable cutting knife lifting .................................................................................................................. 8
24. Setting of the upper thread tensioner releasing .......................................................................................................... 8
25. Setting of the adjusting spring function ....................................................................................................................... 8
26. Setting of the starting position of the movable thread cutter ................................................................................... 9
27. Setting of the stationary knife presure .......................................................................................................................... 9
28. Setting of the stop in the top position of the needle .................................................................................................. 9
29. Making an upper thread reserve ..................................................................................................................................... 9
30. Dismounting and mounting of the plate ........................................................................................................................ 9
31. Dismounting and mounting of the movable cutting knife .......................................................................................... 9
1
Instructions for setting individual mechanisms
1. General safety instructions
The non-observance of the following safety instructions can cause bodily injuries or damages to the machine.
1. The machine must only be commissioned of the instruction book and operated by persons with appropriate training.
2. Before putting into service also read the safety rules and instructions of the motor supplier.
3. The machine must be used only for the purpose intended. Use of the machine without the safety devices is not permitted.
Observe all the relevant safety regulations.
4. When gauge parts are exchanged (e.g. needle, top roller, needle plate, feed dog and bobbin) when treading, when the
workplace is left, and during service work, the machine must be disconnected from the mains by switching off the master
switch or disconnecting the mains plug.
5. Daily servicing work must be carried out only by appropriately trained persons.
6. Repairs, conversion and special maintenance work must only be carried out by technicians or persons with appropriate
training.
7. For service or repair work on pneumatic systems the machine must be disconnected from the compressed air supply system.
Exceptions to this are only adjustments and functions checks made by appropriately trained technicians.
8. Work on the electrical equipment must be carried out only by electricians or appropriately trained persons.
9. Work on parts and systems under electric current is not permitted, except as specified in regulations DIN VDE 0105.
10. Conversion or changes to the machine must be authorized by us and made only in adherence to all safety regulations.
11. For repairs, only replacement parts approved by us must be used.
12. Commissioning of the sewing head is prohibited until such time as the entire sewing unit is found to comply with EC
directives.
It is absolutely necessary to respect the safety instructions marked by these signs.
Danger of bodily injuries !
Please note also the general safety instructions.
IMPORTANT WARNING
In spite of all safety measures made on the machines, inappropriate actions of the operator may lead to dangerous situations. In
industrial sewing machines, attention should be paid to the following still remaining possible sources of injury:
1. Moving sewing needle
- risk of injury when sewing with raised pressure foot or top roller, because the finger guard is then positioned too high.
2. Moving thread take-up lever
- risk of injury when inadvertently or intentionally inserting the finger(s) between the thread take-up lever and its guard.
3. Moving pressure member
- risk of injury when holding sewn work in immediate vicinity of the pressure member and beginning to insert under the
pressure member a considerably thicker sewn work portion,
- risk of injury when sinking the pressure member.
4. When switched off, the clutch motor slows down by inertia but would be reactivated by an accidental treading down of the
motor treadle. To avoid such risk, it is advised to hold the handwheel by hand and slightly to depress the motor treadle.
2. Introduction
This part contains instruction for regulating the mechanisms of the sewing machine head.
For setting the machine, simple setting aids are used which are included in the accessory of the machine. Besides these aids,
universal measuring devices are used, such as slide calliper, feeler gauges and dynamometer for measuring the thread tension.
It is adviceable to order the locating fixture S791 947001 for setting:
- the feeder planeness and and height
- the hook timing
- the hook medium part holder
- presser foot lifting
Especificaciones del producto
| Marca: | Durkopp Adler |
| Categoría: | máquina de coser |
| Modelo: | 525 |
¿Necesitas ayuda?
Si necesitas ayuda con Durkopp Adler 525 haz una pregunta a continuación y otros usuarios te responderán
máquina de coser Durkopp Adler Manuales
20 Octubre 2024
17 Octubre 2024
17 Octubre 2024
13 Octubre 2024
11 Octubre 2024
6 Octubre 2024
28 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
15 Septiembre 2024
máquina de coser Manuales
- máquina de coser AEG
- máquina de coser Ambiano
- máquina de coser Alfa
- máquina de coser Brother
- máquina de coser Sinbo
- máquina de coser Jata
- máquina de coser Emerio
- máquina de coser Singer
- máquina de coser Bernina
- máquina de coser Pfaff
- máquina de coser Juki
- máquina de coser Elna
- máquina de coser Mellerware
- máquina de coser Termozeta
- máquina de coser Jocca
- máquina de coser Toyota
- máquina de coser Husqvarna
- máquina de coser Bernette
- máquina de coser Janome
- máquina de coser Necchi
- máquina de coser Yamato
- máquina de coser Kayser
- máquina de coser RCE
- máquina de coser Veritas
- máquina de coser Union Special
- máquina de coser Easy Home
- máquina de coser Vendomatic
- máquina de coser Baby Lock
- máquina de coser Empisal
- máquina de coser Lewenstein
- máquina de coser Meister Craft
- máquina de coser Yamata
- máquina de coser Weasy
- máquina de coser Victoria
- máquina de coser Prince
- máquina de coser Muller
- máquina de coser Sinojo
- máquina de coser Huskystar
- máquina de coser Gritzner
- máquina de coser W6
- máquina de coser Prixton
- máquina de coser Feiyue
- máquina de coser Husqvarna-Viking
- máquina de coser SteamMax
Últimos máquina de coser Manuales
27 Octubre 2024
27 Octubre 2024
26 Octubre 2024
26 Octubre 2024
26 Octubre 2024
21 Octubre 2024
21 Octubre 2024
21 Octubre 2024
21 Octubre 2024
20 Octubre 2024