Dynaudio DA-BM6A Manual de Usario

Dynaudio Monitor DA-BM6A

Lee a continuación 📖 el manual en español para Dynaudio DA-BM6A (6 páginas) en la categoría Monitor. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/6

DA-BM6A

OWNERS MANUAL

Congratulations on your purchase of the Dynaudio Acoustics BM6A monitor system. With the

right care and attention it will give you many years of trouble free audio reproduction. It is

most important, however, that you take a few minutes at this early stage in your BM6A’s life to

read the following paragraphs. They contain essential information to enable you to get the

best from your monitors.

Electrical Safety Warning

This unit is supplied with a 3 wire power cord. Under no circumstances should the

earth wire be disconnected.

To prevent possibility of shock hazard do not expose the unit to moisture

There are no user serviceable parts inside. Do not open cover. Refer servicing to

qualified personnel only

Ensure correct mains voltage and fuse are selected before connection to mains

BM6A Owner’s Manual - Issue 2 Page 2

November 1997

Setting Up

Mai

MaiMains Po

ns Po

ns Pons Power Co

wer Co

wer Cower Connect

nnect

nnectnnectio

ioions

nsns

Mains power is applied via a fused IEC inlet. The unit must be earthed. The voltage selector

switch is used to match the unit to the mains voltage in your territory. The mains fuse must be

the correct value for the voltage selected, 115V requires a T3.15A fuse while 230V requires a

T1.6A fuse. The ‘T’ signifies a slow blow type fuse.

You must ensure that the correct voltage and fuse have been selected before

switching the unit on.

Audio Co

Audio CoAudio Connect

nnect

nnectnnectio

ioions

nsns

Audio input is via a female XLR connector. The input is electronically balanced with +ve on

pin 2, -ve on pin 3 and ground on pin 1. If your signal source is unbalanced it is usual to

connect the unused signal pin (i.e. Pin 3) to ground. This is normally done inside the

connecting cable. For best results use only good quality screened cables and connectors.

Your local dealer will be able to advise you

Positioning

PositioningPositioning

The BM6A is designed primarily as a ‘nearfield’ monitor and would normally be positioned

1-3m from the listener. They can be mounted on stands or on the meter bridge of the console

(providing this is substantial enough). For best results the speakers should be ‘aimed’ at the

listener in both vertical and horizontal planes.

In any situation ensure that there is adequate space for ventilation around the heatsink.

BM6A Owner’s Manual - Issue 2 Page 3

November 1997

Operation

Controls

ControlsControls

Level switch. This sets the input sensitivity of the unit. The +4 position is intended for

professional use and means that full power is reached with an input level of

+4dBm (balanced). The -10 position is intended for semi-professional or

domestic use and means that full power is reached with an input level of

-10dBm (unbalanced).

HF Trim. This control allows the high frequency level to be adjusted. The control

works from 3kHz upwards and has a range of 5dB (see figure 1).

LF Trim. This control allows the low frequency level to be adjusted. The control works

from 100Hz downwards and has a range of 5dB (see figure 1). This section

uses a special equaliser design which effectively swaps bandwidth for power.

As you turn the LF trim level down the low frequency extension is improved.

The trim controls are intended to allow the user to make some adjustment of the speaker

response to accommodate personal tastes and variations in acoustic environment.

Figure 1 - Trim Control Response

Indicators

IndicatorsIndicators

There are two LED indicators on the front baffle of the BM6A.

The right hand one is the power/fault indicator. On switching the unit on this will shine red for

about ten seconds and then turn green to indicate normal operation. If for any reason the

amplifier protection circuitry is engaged the LED will turn back to red.

The left indicator is a true clip indicator and lights when the low frequency amplifier clips. It is

acceptable to run the system with this lighti running the system withng occasionally but avoid

this lighting most of the time

Running In

Running InRunning In

Especificaciones del producto

Marca:	Dynaudio
Categoría:	Monitor
Modelo:	DA-BM6A
Color del producto:	Zwart
Peso.:	4476 g
Ancho:	1034 mm
Profundidad:	155.5 mm
Altura:	71.7 mm
Peso del embalaje:	16000 g
Ancho del embalaje:	765 mm
Empaquetadura en profundidad:	260 mm
Altura del embalaje:	371 mm
Manual de usuario:	Ja
Bluetooth:	Ja
Tecnología de conectividad:	Draadloos
Cables suministrados:	AC
Tarjeta de garantía:	Ja
Dimensiones del paquete (AnxPrxAl):	765 x 260 x 371 mm
Número de puertos HDMI:	3
Energía promedio:	210 W
Consumo de energía (en espera):	0.5 W
Número soportado de baterías/baterías:	2
Radio FM:	Nee
Versión HDMI:	1.4
Decodificadores de audio incorporados:	DTS Digital Surround, Dolby Digital 5.1
Número:	1
subwoofer de potencia media:	90 W
Canales de salida de audio:	4.1 kanalen
Altavoz de graves con controlador de diámetro (imperial):	1 "
Sistema de suspensión para la pared.:	Ja
Entrada HDMI:	2
Cantidad de cartón exterior:	1 stuk(s)
Peso-del-embalaje:	3293 g
Peso bruto del cartón exterior:	13.44 kg
peso neto omdoos:	10.147 kg
Embalaje de peso neto:	10.147 kg
Peso de tara del embalaje:	3.293 kg
Peso-del-paquete:	3.293 kg
Potencia RMS del altavoz de la barra de sonido:	120 W
Distorsión Armónica Total (THD):	30 procent
subwoofer suministrado:	Ja
Receptor suministrado:	Nee
Soportes de montaje incluidos:	Ja
Compatibilidad con acoplamiento de Apple:	Niet ondersteund
Entrada óptica de audio digital:	1
Peso de la barra de sonido:	4476 g
Número de salidas HDMI:	1
Rango de frecuencia del subwoofer:	20 - 150 Hz
Impedancia del subwoofer:	4 Ohm
Ancho del subwoofer:	200 mm
Altura del subwoofer:	510 mm
Profundidad del subwoofer:	200 mm
Peso del subwoofer:	5000 g
Diámetro del altavoz de graves:	6.5 "
Dimensiones del subwoofer (An x Al x Pr):	200 x 510 x 200 mm
Diámetro hogetonenluidspreker:	1 "
Número de controladores de tweeter:	2
Mando a distancia incluido:	Ja
Entrada de audio digital (coaxial):	1
Peso bruto del embalaje principal (exterior):	13440 g
Altura (cm):	37.1 cm
Longitud (cm):	76.5 cm
Ancho (cm):	26 cm
Peso de la unidad principal:	4180 g
Dimensiones de la unidad principal (AnxPrxAl):	1035 x 156 x 70 mm
voltaje-de-entrada-de-CA:	110 - 240 V
Frecuencia-de-entrada-de-CA:	50 Hz
Baterias-incluidas:	Ja
Controladores de altavoz:	3"