Elektrobock Pocket Home PH-SP2 Manual de Usario

Elektrobock receptor Pocket Home PH-SP2

Lee a continuación 📖 el manual en español para Elektrobock Pocket Home PH-SP2 (4 páginas) en la categoría receptor. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
Version 11.02
Wireless receiver for control of
electric heating devices
- WALL-MOUNTED -
PH-SP2
Operating instructions
Control of electric heating systems
Component of the PocketHome
®system
Two-way radio communication at 433,92 MHz
The connected electric appliance is switched according to
the required temperature
The control unit PH-BSP is the pilot component
The device can only be installed by a person with adequate qualification!
The installation must be executed in a voltage-free state!
holes for
installation
on KU/KP68
Fig.1 Fig.2 Fig.3
230 V/ 50 Hz
Wiring diagram:
L
N
FUNCTION BUTTON:
SHORT PRESSING - coding.
LONG PRESSING (for about 5 s) - RESET
deleting the code from the memory (the green and
red LEDs flash simultaneously).
max.
16 A
Fig.4
INSTALLATION
output terminals
power supply
terminals
FUNCTION
BUTTON
PH-SP2 is used for switching the heating device in connection
with the PH-BSP control unit.
ACTIVATION PROCEDURE
1. Lift off the front cover of the receiver acc. to Fig. 1, 2.
2. Attach the receiver to the wall (or to the wiring box directly).
3. Switch off the main circuit breaker.
4. Connect the receiver acc. to the diagram.
5. Connect the receiver to the mains 230 V / 50 Hz.
6. Switch on the main circuit breaker; the green diode flashes
on the receiver; thus the receiver is ready for further setting.
7. Shortly press the FUNCTION BUTTON
for about 1.5 s (the green and red
diode are flashing alternately).
8. On the PH-BSP control unit, press the” Test ”
button in the ACTIV mode to activate the
SP switching components (see page 10 of
the PH-BSP instructions).
9. If the code has been learned correctly,
the green and red diodes flash
simultaneously.
INDICATION DIODES
LED 2LED 1
empty memory, code not learned
code learned
FLASHING ALTERNATELY= code learning mode
FLASHING SIMULTANEOUSLY= code has been learned
SIMULTANEOUS LONG FLASH= code was ERASED
relay switched
ERROR (if no signal is received from the
transmitter within approx. 6 hours, it switches to
the 2-min-ON / 8-min-OFF mode). LED flashes
only if the relay is on, i.e. for 2 minutes.
EXPLANATION: LIT UNLIT FLASHING
FUNCTION

Especificaciones del producto

Marca: Elektrobock
Categoría: receptor
Modelo: Pocket Home PH-SP2

¿Necesitas ayuda?

Si necesitas ayuda con Elektrobock Pocket Home PH-SP2 haz una pregunta a continuación y otros usuarios te responderán


receptor Elektrobock Manuales

Elektrobock

Elektrobock Pocket Home PH-SP2 Manual de Usario

12 Agosto 2024

receptor Manuales

Últimos receptor Manuales

Crown

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024
Boss

Boss PT3000 Manual de Usario

27 Octubre 2024
Speco Technologies

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024
Fosi Audio

Fosi Audio V3 Manual de Usario

26 Octubre 2024
Jensen

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024
Onkyo

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024
Pioneer

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024
Yamaha

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024
NAD

NAD C 355BEE Manual de Usario

20 Octubre 2024
Yamaha

Yamaha RX-A810 Manual de Usario

20 Octubre 2024