Eltako DL-PD-300W-RLC-HS Manual de Usario

Eltako No categorizado DL-PD-300W-RLC-HS

Lee a continuación 📖 el manual en español para Eltako DL-PD-300W-RLC-HS (1 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/1
Phase dimmer with DALI control input for
DIN top-hat rails DIN-EN 60715 TH35.
98x17,5x56 mm. Protection class IP20.
Suitable for dimming 230 V LED retrot
luminaries using DALI Converts DALI dimming
level to a voltage with leading or trailing edge.
The minimum dimming level (MIN LEVEL) is
adjustable via DALI. Additional operating
mode as switch (conforms to DT7) as from
Firmware 3.5. The module represents a bus
user and is therefore addressable. Double
terminals for easy looping of the DALI bus.
Dimming range 0.1%-100
Supply voltage 230 V AC.
Output load range 10-300 W.
High eciency. Conguration via DALI
Cockpit PC software.
Function:
The DALI PD is an interface between classic
dimming technology (phase dimming) and
DALI which is based on the standard for DALI
Control Gear (IEC 62386-102) and Device
Type 4 equipment (IEC 62386-205). The DALI
PD interface converts the required dimming
level into a corresponding voltage signal with
leading or trailing edge. Depending on the load
the universal dimmer operates as a leading
or trailing edge dimmer. The operating mode
can be requested over DALI (DT4). The dimming
characteristic is based on a logarithmic
scale as stipulated in the DALI standard.
The leading or trailing edge control supplies
a sinusoidal voltage with a phase-cut on the
Phase dimmer with DALI control input
(DT4)
DL-PD-300W-RLC-HS
GB
Temperature at mounting location:
-20°C up to +50°C.
Storage temperature: -25°C up to +70°C.
Relative humidity:
annual average value <75%.
33 000 008 - 1
Only skilled electricians may install this
electrical equipment otherwise there is
the risk of re or electric shock!
leading or trailing edge. The PHYSICAL MIN-
LEVEL is 3%.
As of Firmware version 3.5 the DALI PD is
equipped with an additional operating mode.
It is switchable from DT4 operating mode
(phase dimming) to DT7 (switch). In this
operating mode the DALI PD acts as a switch.
Its behaviour in this mode corresponds to the
DALI standard for DT7 devices (IEC62386-208).
In this operating mode the switch characteristic
is determined by comparing the virtual dim
level (VDAP) with 4 switching thresholds.
The virtual dim level (VDAP) corresponds to
the dim level of a DALI electronic ballast with
its corresponding characteristics (limited
by MINLEVEL and MAXLEVEL, dimming
speed limited by fade time and fade rate).
There are 2 switching thresholds in each
dimming direction and they are used for
comparison with the virtual dim level:
A threshold with the value 'MASK' is inactive
and is not used in the comparison.
Switch-on/off delays can be implemented
with fading.
The device is powered from the DALI bus so
that there is only partial support for the
SYSTEM FAILURE LEVEL. On current devices
(identied by Firmware > 4.0), you can choose
between 0%,100% and MASK. On older models
the SYSTEM FAILURE LEVEL is xed - the 25 W
variant outputs 100%; the 300 W variant
outputs 0%.
Technical data
Output load range 10-300 W
Screw terminals:
Max conductor
cross-section 2,5 mm2
Must be kept for later use!
Eltako GmbH
D-70736 Fellbach
Technical Support English:
+49 711 94350025
technical-support@eltako.de
eltako.com
05/2022 Subject to change without notice.
The crossed-out waste container indicates
that batteries may not be disposed with
other household or commercial waste.

Especificaciones del producto

Marca: Eltako
Categoría: No categorizado
Modelo: DL-PD-300W-RLC-HS

¿Necesitas ayuda?

Si necesitas ayuda con Eltako DL-PD-300W-RLC-HS haz una pregunta a continuación y otros usuarios te responderán




No categorizado Eltako Manuales

No categorizado Manuales

Últimos No categorizado Manuales