EMOS M0391 Manual de Usario
EMOS
Multimeter
M0391
Lee a continuación 📖 el manual en español para EMOS M0391 (27 páginas) en la categoría Multimeter. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/27
2202007000_31-M0391_00_01 115 × 165 mm
www.emos.eu
M0391 | MD-210
GB Digital Multimeter
CZ Digitální multimetr
SK Digitálny multimeter
PL Multimetr cyfrowy
HU Digitális multiméter
SI Digitalni multimeter
RS|HR|BA|ME Digitalni multimetar
DE Digitales Multimeter
UA Цифровий мультиметр
RO|MD Multimetru digital
LT Skaitmeninis multimetras
LV Digitālais multimetrs
EE Digitaalne multimeeter
BG Цифров мултиметър
5
measuring tips the spot or circuit where you
wish to measure AC voltage.
If you do not know the voltage range before-
hand, set the largest possible range and gradually
decrease it as you measure.
3. Turn on the device you want to measure. The
screen will display the voltage value and polarity
relative to the red measuring tip.
If you exceed the range of 300 V, immediately
stop measuring. Otherwise, you risk damaging the
multimeter and suering injury by electric current.
Measuring Direct Current
1. Connect the plug of the red measuring conduc -
tor into the socket and the black conductor
into the COM socket. If the measured voltage
is between 200 mA and 10 A, connect the
plug of the red measuring conductor into the
10 A socket.
2. Turn the circular switch to function marked .
3. Connect the multimeter serially to the circuit
you wish to measure and turn on the power
supply to the measured device.
4. The screen will display the measured current
and polarity relative to the red measuring tip.
Never use the device to measure current in
places where the idle voltage in an open circuit
exceeds 300 V.
Measuring current at higher idle voltage could result
in damage to the device (fuse burnout, electric
discharge) or injury by electric current!
Measuring Resistance
1. Connect the plug of the red measuring conduc -
tor into the “ socket and the black conductor
into the COM socket.
2. Turn the circular switch to function marked .
Select measuring range. Turn o the power sup-
ply to the circuit and discharge all high-voltage
capacitors before measuring resistance in the
circuit. Doing so prevents potential damaging
of the multimeter.
3. Connect the measuring tips to the device or
circuit where you wish to measure resistance.
4. The screen will show the measured resistance
value.
Note:
1. When measuring resistances higher than 1 MΩ,
it is necessary to wait a few seconds before the
measured value stabilizes.
2. If the circuit is open, the ”OL” symbol will
appear, same as when the measuring range is
exceeded. Before measuring resistance, make
sure that the measured object is disconnected
from power supply and all its capacitors are
fully discharged.
Diode Test
1. Connect the plug of the red measuring conduc -
tor into the socket and the black conductor
into the COM socket.
2. Turn the circular switch to function marked .
3. Place the red measuring tip onto the diode‘s
anode and then the black measuring tip onto
the diode‘s cathode.
4. The screen will show voltage in mV for the
direction of current ow. „OL“ will appear on
the screen if the polarity has been reversed.
Circuit Continuity Test
1. Connect the plug of the red measuring conduc -
tor into the socket and the black conductor
into the COM socket.
2. Turn the circular switch to function marked .
3. Connect the measuring tips to the tested circuit
or device. If resistance is lower than 20 Ω, you
will hear a buzzer.
Note: Before making measurements, make sure that
the measured circuit is disconnected from power
supply and all its capacitors are fully discharged.
Changing Batteries
If the display shows the symbol, the battery
needs replacing. Use a suitable screwdriver to
change the battery.
Before changing the battery, disconnect the meas-
uring tips from the measured circuit or device and
turn the switch to the OFF position.
Unscrew the rear cover.
Replace the 9 V type 6F22 battery with a new one.
Use alkaline batteries only. Do not use rechargeable
batteries.
Make sure to observe the correct polarity. After
changing the battery, replace the cover and screw
it back on.
Replacing the Fuse
If the fuse burns out, it is most likely caused by
improper handling. The multimeter uses fuses with
these parameters:
F 250 mA/300 V, ø 5×20 mm, F 10 A/300 V,
ø 5×20 mm.
The fuse is located under the battery cover. Always
replace the fuse with a fuse of the same type and
parameters. Replace the battery cover and close
it shut.
To replace the F 10 A L 300 V fuse, contact a
service centre.
Before changing a fuse, disconnect the measuring
tips from the measured circuit or device and turn
the switch to the OFF position.
This device is not intended for use by persons (in-
cluding children) whose physical, sensory or mental
disability or lack of experience and knowledge
prevents safe use, unless they are supervised or
8
Stejnosměrný proud (DC)
Rozsah Rozlišení Přesnost
20 µA 0,01 µA ±(1,2 % + 5)
200 µA 0,1 µA
±(1 % + 5)2 000 µA 1 µA
20 mA 10 µA
200 mA 100 µA ±(1,2 % + 5)
10 A 10 mA ±(2 % + 5)
Ochrana při přetížení:
Rozsah µA a mA pojistka F 250 mA/300 V
Rozsah 10 A pojistka F 10 A/300 V
Maximální vstupní proud:
Zdířka max. 200 mA
Zdířka 10 A max. 10 A
Při měření proudu větším jako 2 A; délka měření musí
být maximálně 10 sekund a další měření opakovat
až po 15 minutách!
Odpor
Rozsah Rozlišení Přesnost
200 Ω 0,1 Ω
±(1,2 % + 5)
2 kΩ 1 Ω
20 kΩ 10 Ω
200 kΩ 100 Ω
2 MΩ 1 kΩ
Napětí otevřeného obvodu: max 1 V
Test diod a spojitosti obvodů
Rozsah Popis Poznámka
Na displeji se objeví
přibližné napětí diody
v propustném směru.
Napětí bez
zátěže: 2,2 V
Vestavěný bzučák
signalizuje, že odpor
v obvodu je menší než
20 Ω.
Pokud je odpor mezi 20 Ω
až 150 Ω, bzučák může,
ale nemusí zaznít.
Pokud je odpor větší než
150 Ω, bzučák nezazní.
Napětí bez
zátěže: 2,2 V
Měření stejnosměrného napětí
1. Připojte koncovku červeného měřicího vodiče do
zdířky označené „ “ a černý vodič do zdířky
označené „COM“.
2. Kruhovým přepínačem přepněte na funkci
označenou . Zvolte měřicí rozsah a připojte
měřicí hroty na místo nebo obvod, kde budete
měřit stejnosměrné napětí.
Neznáte-li napěťový rozsah předem, nastavte
nejvyšší rozsah a postupně ho při měření snižujte.
3. Zapněte napájení do zařízení, které budete
měřit. Na displeji se zobrazí hodnota napětí a
polarita vztažená k červenému měřicímu hrotu.
Při překročení rozsahu 300 V okamžitě ukončete
měření. V opačném případě hrozí poškození multi-
metru a úraz elektrickým proudem.
Měření střídavého napětí
1. Připojte koncovku červeného měřicího vodiče do
zdířky označené „ “ a černý vodič do zdířky
označené „COM“.
2. Kruhovým přepínačem přepněte na funkci
označenou . Zvolte měřicí rozsah a připojte
měřicí hroty na místo nebo obvod, kde budete
měřit střídavé napětí.
Neznáte-li napěťový rozsah předem, nastavte
nejvyšší rozsah a postupně ho při měření snižujte.
3. Zapněte napájení do zařízení, které budete
měřit. Na displeji se zobrazí hodnota napětí a
polarita vztažená k červenému měřicímu hrotu.
Při překročení rozsahu 300 V okamžitě ukončete
měření. V opačném případě hrozí poškození multi-
metru a úraz elektrickým proudem.
Měření stejnosměrného proudu
1. Připojte koncovku červeného měřicího vodiče do
zdířky označené „ “ a černý vodič do zdířky
označené „COM“. Je-li měřený proud v rozmezí
200 mA až 10 A zapojte koncovku červeného
měřicího hrotu do zdířky označené „10 A“.
2. Kruhovým přepínačem přepněte na funkci
označenou .
3. Připojte multimetr do série obvodu, kde chcete
měřit proud, zapněte napájení měřeného
zařízení.
4. Na displeji se objeví hodnota naměřeného
proudu a polarita vztažená k červenému mě-
řicímu hrotu.
Nikdy neměřte přístrojem proud tam, kde je na-
pětí naprázdno v otevřeném obvodu vyšší než 300 V.
Měření proudu při vyšším napětí naprázdno by mohlo
vést k poškození přístroje (shoření pojistky, elektric-
kému výboji) případně k úrazu elektrickým proudem!
Měření odporu
1. Připojte koncovku červeného měřicího vodiče do
zdířky označené „ “ a černý vodič do zdířky
označené „COM“.
2. Kruhovým přepínačem přepněte na funkci ozna-
čenou . Zvolte měřicí rozsah. Vypněte zdroj
napájení připojený k obvodu a vybijte všechny
vysokonapěťové kondenzátory před tím, než
provedete měření odporu v obvodu. Předejdete
tím možnému poškození multimetru.
3. Připojte měřicí hroty na zařízení nebo obvod,
kde budete měřit odpor.
4. Na displeji se objeví hodnota naměřeného
odporu.
Poznámka:
1. Při měření odporů s hodnotou vyšší jak 1 MΩ je
nutné počkat několik sekund, než se měřená
hodnota stabilizuje.
Especificaciones del producto
Marca: | EMOS |
Categoría: | Multimeter |
Modelo: | M0391 |
¿Necesitas ayuda?
Si necesitas ayuda con EMOS M0391 haz una pregunta a continuación y otros usuarios te responderán
Multimeter EMOS Manuales
29 Agosto 2024
Multimeter Manuales
- Multimeter Alecto
- Multimeter Appa
- Multimeter Amprobe
- Multimeter Ferm
- Multimeter Stanley
- Multimeter Parkside
- Multimeter Milwaukee
- Multimeter Extech
- Multimeter Tacklife
- Multimeter Metrix
- Multimeter Benning
- Multimeter Voltcraft
- Multimeter Somogyi
- Multimeter Velleman
- Multimeter Kyoritsu
- Multimeter Ideal
- Multimeter Testboy
- Multimeter Hager
- Multimeter Topcraft
- Multimeter TFA
- Multimeter Clas Ohlson
- Multimeter Powerfix
- Multimeter Owon
- Multimeter Fluke
- Multimeter Jung
- Multimeter Greenlee
- Multimeter Högert
- Multimeter Laserliner
- Multimeter REV
- Multimeter Testo
- Multimeter Bruder Mannesmann
- Multimeter Monacor
- Multimeter Multimetrix
- Multimeter Digi-tool
- Multimeter GW Instek
- Multimeter Elma
- Multimeter Uni-T
- Multimeter Mastech
- Multimeter PeakTech
- Multimeter Chauvin Arnoux
- Multimeter Gossen Metrawatt
- Multimeter PCE Instruments
- Multimeter Klein Tools
- Multimeter Aim TTi
- Multimeter Sanwa
- Multimeter EEVBlog
- Multimeter Qian
Últimos Multimeter Manuales
14 Septiembre 2024
14 Septiembre 2024
13 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024
10 Septiembre 2024