Eureka Spitfire 2 Manual de Usario
Lee a continuación 📖 el manual en español para Eureka Spitfire 2 (2 páginas) en la categoría Carpa. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Contents of Carry bag
Tent body
Tent fly
Pole bag: 2 poles with prebends to make hoops, 1 longer
(head-end pole) & 1 shorter (foot-end pole)
Stake bag: stakes & guyout cords
Setting up the Tent Body
1. Spread the tent body out, floor side down. Locate the
yellow webbing stake out loop, as this marks the head-end of
the tent. Securely stake the yellow webbing loop to the
ground.
2. Assemble the two poles, placing the longer pole near the
head-end of the tent & the shorter pole near the foot area.
3.Starting near the head-end of the tent, insert the tip of the
long pole into the grommet (metal ring) located in the black
webbing stake out loop. Insert the other pole tip into the
grommet on the opposite side of the tent. Reach down to the
tent body & connect all of the black plastic clips to the pole.
4. Repeat the process near the foot-end of the tent with
second, shorter pole
5. To raise your tent, grasp the black webbing loop with the
side-release buckle at the tip of the foot-end. As you pull the
webbing, the poles will raise. When fully tensioned, the poles
will be upright. Securely stake the black webbing loop to the
ground.
6. Futher secure the tent to the ground by using stakes in the
black webbing loops at the base of each pole.
Attaching the Fly Sheet
1. Unfold the fly & drape it over the tent matching the
yellow webbing on the fly with the yellow webbing on the
tent body. Align and center the fly on the tent body so the
fly’s seams follow the tent body’s poles.
2. Clip together the side-release buckle on the yellow
webbing.
3. Locate the bright green webbing guyout loops on the
outside of the flysheet, reaching under the guyout loops,
wrap the hook/loop closure around the underlying pole to
secure the fly to the pole. Secure the guyout loops at both
the head-end & foot-end poles.
4. Clip together the side-release buckles in the black
webbing at the tip of foot-end.
5. Now clip the buckles at the base of the foot-end pole.
6. Further tension the fly by pulling the webbing through
the 4 side-release buckles you have closed.
7. Using stakes, secure the two remaining stake-out loops
on the fly to create your vestibules.
8. Guyouts: Attach the two provided guyout cords to the
green webbing guyout loops on the head-end pole. If you
expect severe weather, utilize the guyouts on the foot-end
pole. Get in the habit of always using the guyouts, even in
good weather.
Eureka! Set-Up Instructions
Spitfire Solo (#2628314)
Spitfire 2 (#2628318)
REV 082714
Special Feature:
This tent features a poke-up vent in the fly. Lift the vent
open & prop it open with the stay. One can access the
vent from inside the tent through the zipper located in
the ceiling.
OTHER FEATURES
7. The tent body will now be erect, properly tensioned,
and anchored to the ground.
v
e
n
t
o
u
t
o
f
v
i
e
w
Good:
4 stakes /4 lines
Best:
4 stakes /8 lines
SEAM SEALING:
We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett
Outdoor SeamGrip
®
.
• Work in a fully ventilated area.
• Set the tent up or lay the tent out flat. Taut seams allow for even
application and penetration of the sealer.
• Decide which seams need to be sealed. For example, seams that will be
exposed to rain, runoff, or ground level water are a must for sealing, while
seams on uncoated nylon or mesh panels don’t need treatment. There is
no need to seal the seams in the roof or the factory taped seams. We
recommend sealing both floor and fly seams and reinforcements.
• Apply sealant to the inside and outside of all exposed seams. Several thin
layers will work better than one thick layer. Read and follow
manufacture's instructions.
STAKING:
All tents need to be staked down to keep them from blowing away.
Securing the tent by placing heavy objects inside is just not adequate.
• Once the tent body is erected, stake it out before the fly is put on. This
enables you to square the tent up to ensure that the fly goes on properly
and that the seams align with the frame. Pull the base of the tent taut
between each web stake out loop or ring & pin. Make sure that all corners
are square. It is important that you don’t stake the tent out too tightly.
You will know it’s too tight, if the door zippers can not be easily operated.
Drive stakes through the web loops, or with ring & pin, drive the stake
just outside the ring so that the “J” hook catches it. Tie a piece of cord or
web into a loop through the ring to be used as a large stake loop if
needed.
• With the tent properly staked, drape the fly over the frame, attach its tent
connection points and stake down any pull outs.
• Do not attempt to remove the stakes by pulling on the tent becket loop,
as this could cause the fabric to tear. The best way is to pry on the stake
itself.
STAKING IN SPECIAL CONDITIONS:
• Sand. Use long, broad stakes with plenty of surface area in loose soil.
• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes
separately. Their sharp edges can cut fabric and leave rust stains, which
might damage your tent.
• Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent
bags, or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski
poles, which are stuck in the snow.
GUY LINES:
Do not depend upon staking alone to keep your tent secure during high
winds. Most tent models have built-in loops or rings at optimal guy out
locations. It’s important to put in the extra time guying out your tent.
Correctly done, it can save your tent during exceptional weather.
• Make sure that the top fly is securely attached to the tent frame. Ties, hook
and loop, or dog-bones and elastic loops are sewn to the underside of the
fly for this purpose.
• Attach parachute cord to the loops/rings and stake them in the ground
three or four feet from the edge of the tent. If staked too close to the tent,
wind can cause an upward pull that could dislodge the stakes.
• If your tent does not have loops or rings for guy outs, attach guy lines 1/3
to 1/2 of the way up the framework on the main sidewalls. This enables
the guy line to support the lower section of the pole, while the upper
pole can flex and deflect wind gusts. It is best to run two cords at an
angle from the side of the guy out. This prevents all movement, except
toward the anchor. The guy lines will work together through opposition.
See illustrations.
CONDENSATION & VENTING:
Through perspiration and breathing, an adult gives off about a pint of
water overnight. If it cannot escape, the water vapor condenses to liquid.
Most often, water found in the tent is a result of this condensation rather
than from the tent leaking. Condensation often forms where the sleeping
bag touches the side of the tent, under the sleeping pad, or on coated
surfaces such as the door flaps. A tent’s double wall construction allows
the vapor to escape through the roof to the outside, keeping the inside of
the tent dry.
Leave the windows partially open at night to provide cross ventilation and
further reduce condensation. Cross ventilation becomes more important
in very humid or extremely cold conditions when the permeable roof is
less effective. The features that enhance ventilation are windows,
short-sheeted flys (bottom venting), roof vents, and High/Low venting
doors. These are specific to each tent model.
Given the importance of proper ventilation, We use High/Low venting in
most of our tents. This allows cooler air in through the low vents and
warmer, moist air up and out through the high vents. High/Low venting is
accomplished within the inner tent via roof vents, doors and windows. It
is important to vent the vestibule. Unvented, it can inhibit airflow into the
tent. Our tent vestibules profit from the ability to “short sheet” by means
of zippers & toggles and staked vestibule pull outs create a bellowing
effect.
Most of our tents are equipped with a High/Low venting door. This design
allows increased airflow into the tent from the bottom. Open the low
vent/window to admit cool air, allowing the warmer air out through the
high roof vents. When rain and wind prevent the low vent from being
opened, the high door vent can still be used. Fly overhangs or vestibules
protect it.
ULTRAVIOLET LIGHT:
Ultraviolet light damage to tent fabric is caused by excessive exposure to
sunlight. While our fabrics are UV resistant, any synthetic fabric is
susceptible to UV degradation. UV damage will cause nylon and polyester
to become brittle and tear easily. We recommend that you use the rain fly
even on clear days. It acts as a sunscreen to the tent. A rain fly is both
easier and less expensive to replace if damaged. UV damage can be
minimized by erecting tents on shaded sites with low exposure to direct
sunlight.
GENERAL POLE CARE:
• Never let tent poles snap together as this can damage the pole end.
• Do not drop tent or pole bags on their ends and do not bounce a tent bag
on its end to get the tent out. These actions may cut the shock cord and
damage the pole ends.
• The aluminum frame may bend slightly and take a “set” through usage;
this normally does not affect the performance of the frame.
GENERAL TENT CARE:
• Sweep the tent floor daily to prevent damage from stones.
• Try not to wear shoes inside your tent.
• Use a ground cloth whenever possible.
• Do not keep food inside a tent. Hungry critters will chew through
tent fabric in search of food.
STORAGE:
• Make sure the tent is completely dry, then store loosely rolled, in a
dry, cool place. To prevent dust from collecting on the tent, cover it
with a cloth. This allows the nylon/polyester fabric to breathe.
• Ideally, the tent poles should be stored in their fully assembled state.
This reduces the tension on the shock cord, prolonging its life.
• The tent bag should be used only as a carry sack and not for storage.
COLOR TRANSFER:
• Do to the nature of tent fabrics, color can transfer from darker to
lighter fabrics when the two fabrics are in contact over time when
wet, damp or exposed to the combination of moisture and high
heat. This does not effect the tent's performance. To prevent /
minimize color transfer, always make sure your tent is completely dry
prior to packing and storage.
CLEANING:
• Clean the tent by setting it up and wiping it down with a mild soap
(liquid hand soap) and lukewarm water solution. Rinse thoroughly
and dry completely. Never use detergent, washing machines or
dryers because they can damage the tent’s protective coating and
seams. After cleaning, be sure the tent is completely dry, especially
the heavier, double-stitched areas such as the seams, before storing
or mold / mildew are likely to grow.
• Clean the tent poles with a cloth and lubricate them with silicone
spray. This is especially necessary after ocean side camping to
remove salt spray so the poles don’t corrode or stay gritty.
• Clean the zippers with a quick dip in water and then dry them off.
This is especially important if you’ve been camping in a location with
sand/dirt. If you don’t clean the zippers, the sliders will wear out and
eventually the teeth will become inoperable.
ALTERATIONS OR MODIFICATIONS:
DO NOT misuse, modify or alter this product in any way from its
condition at the time of sale. Alteration, modication or any use of
this product contrary to the accompanying written instructions shall
void the warranty. Moreover, any misuse, alteration or modication
of the product shall absolve Johnson Outdoors Gear LLC of any
liability for property damages or injuries sustained as a result of such
misuse, modication or alteration.
LIMITED WARRANTY:
What Is Covered: Johnson Outdoors Gear LLC
warrants to the original
purchaser that its products are free from defects in material and
workmanship, for the life of the product, except as qualified below. The
life of the product is determined from the date of purchase until such
time as the product is no longer serviceable due to normal wear and
tear.
What Is Not Covered:
Johnson Outdoors Gear LLC
shall not be responsible
for the natural breakdown of materials that occurs inevitably with
extended use (e.g., Ultra Violet (UV) light damage on tents, exhausted
zippers), or defects caused by accident, abuse, alteration, animal attack,
storm damage, misuse or improper care.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS
OF THIS LIMITED WARRANTY.
IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC
BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGES.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
What Johnson Outdoors Gear LLC Will Do: If after
inspection we find that a product failed due to a
manufacturing or material defect, we will repair or
replace the product, at our option, without charge.
How to Obtain Warranty Service: Return the product,
freight prepaid, to the Dealer from whom it was
purchased; or, contact our Customer Satisfaction
Department for return authorization: toll free
1-800-572-8822. Collect shipments or shipments without
return authorization cannot be accepted. The product
registration card packaged with our product need not
be returned for the warranty to be effective and for you
to receive warranty service.
Repairs: If your
Johnson Outdoors Gear LLC
product
needs service or repair due to normal wear and tear,
animal attack, accident or some other reason that is not
covered under the warranty we will provide the
necessary service for a reasonable charge, plus shipping
and handling. We require that products accepted for any
repair be properly cleaned according to our
recommended care instructions. Please send your
product or component that requires
repair (e.g., tent fly),
postage prepaid, along with a description of what needs
attention. For service and repairs, please contact our
Customer Satisfaction Department: toll free
1-800-572-8822
How State Law Relates To This Warranty: This warranty gives
you specific legal rights, and you may have other rights
that vary from state to state.
Our brands are part of the Johnson Outdoors
family of products. Visit all the brands at
johnsonoutdoors.com
We support the "Leave No Trace" Seven
Principles:
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7 . BE COURTEOUS OF OTHER VISITORS
JOHNSON OUTDOORS GEAR INC
WARNING:
KEEP ALL FLAME AND HEAT SOURCES
AWAY FOM THIS TENT!
This tent meets the ammability requirements of CPAI-84. The Fabric may burn
if continuous cntact with any ame source. Do NOT operate any device which
burns fuel inside your tent. This could lead to serious injury or death.
REV 082714
Especificaciones del producto
| Marca: | Eureka |
| Categoría: | Carpa |
| Modelo: | Spitfire 2 |
¿Necesitas ayuda?
Si necesitas ayuda con Eureka Spitfire 2 haz una pregunta a continuación y otros usuarios te responderán
Carpa Eureka Manuales
7 Octubre 2024
5 Octubre 2024
30 Septiembre 2024
23 Septiembre 2024
23 Septiembre 2024
17 Agosto 2024
15 Agosto 2024
15 Agosto 2024
13 Agosto 2024
11 Agosto 2024
Carpa Manuales
- Carpa IKEA
- Carpa Walker
- Carpa Bestway
- Carpa Crivit
- Carpa SereneLife
- Carpa De Waard
- Carpa Outwell
- Carpa Easy Camp
- Carpa Thule
- Carpa Vango
- Carpa Big Agnes
- Carpa Dometic
- Carpa Velleman
- Carpa Babymoov
- Carpa Vaude
- Carpa Nomad
- Carpa Fiamma
- Carpa Perel
- Carpa Skandika
- Carpa Black Diamond
- Carpa Wechsel
- Carpa Chinook
- Carpa Asaklitt
- Carpa Camp Master
- Carpa Zempire
- Carpa Trigano
- Carpa Mx Onda
- Carpa Hilleberg
- Carpa Isabella
- Carpa Wynnster
- Carpa Robens
- Carpa Cabanon
- Carpa Coleman
- Carpa Raclet
- Carpa Goldcamp
- Carpa Kelty
- Carpa Vrijbuiter
- Carpa Brunner
- Carpa MSR
- Carpa Dwt-Zelte
- Carpa LECO
- Carpa TOOLPORT
- Carpa Robinhood
- Carpa Gerjak
- Carpa High Peak
- Carpa Hamron
- Carpa Khyam
- Carpa Black Wolf
- Carpa Nordisk
- Carpa Grand Canyon
- Carpa San Hima
- Carpa Mountain Hardwear
- Carpa Gazebo Penguin
- Carpa Sojag
- Carpa Calima
- Carpa Yamazen
Últimos Carpa Manuales
27 Octubre 2024
23 Octubre 2024
8 Octubre 2024
7 Octubre 2024
2 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
30 Septiembre 2024